GeoVision GV Series Bedienungsanleitung
GV-Surround Video IP Camera
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use. SV48000-QG-A
Quick Start Guide
© 2019 GeoVision, Inc. All rights reserved.
Under the copyright laws, this manual may not be copied, in whole or in part,
without the written consent of GeoVision.
Every effort has been made to ensure that the information in this manual is
accurate. GeoVision, Inc. makes no expressed or implied warranty of any kind
and assumes no responsibility for errors or omissions. No liability is assumed
for incidental or consequential damages arising from the use of the information
or products contained herein. Features and specifications are subject to
change without notice.
Note: No memory card slot or local storage function for Argentina.
GeoVision, Inc.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: +886-2-8797-8377
Fax: +886-2-8797-8335
http://www.geovision.com.tw
Trademarks used in this manual: GeoVision, the GeoVision logo and GV
series products are trademarks of GeoVision, Inc. Windows is the registered
trademark of Microsoft Corporation.
November 2019
Contents
Note for Connecting to GV-VMS ..........................................................iii
Note for Recording................................................................................iii
Note for Installing Camera....................................................................iv
Note for Silica Gel Bags........................................................................iv
Optional Accessories.............................................................................v
1. Introduction......................................................................................1
1.1 Packing List ............................................................................................................1
1.2 Overview.................................................................................................................2
2. Installation........................................................................................3
3. Connecting the Camera ..................................................................6
4. Accessing GV-SV48000...................................................................8
4.1 Web Browser ..........................................................................................................8
4.2 Checking the Dynamic IP Address .........................................................................9
4.3 Configuring the IP Address...................................................................................10
5. The Integrated Web Interface .......................................................12
5.1 Expansive Mode ...................................................................................................12
5.2 Camera Settings...................................................................................................13
6. Upgrading System Firmware ........................................................14
7. Restoring to Factory Default ........................................................15
7.1 Using the Web Interface.......................................................................................15
7.2 Directly on the Camera.........................................................................................15
Note for Connecting to GV-VMS
The GV-SV48000 is designed to work with GV-VMS, a video management system. Note the
following when the camera is connected to GV-VMS:
1. By default, the images are recorded to the memory card inserted in GV-SV48000.
2. Once the camera is connected to the GV-VMS, the resolution set on the GV-VMS will
override the resolution set on the camera’s Web interface. You can only change the
resolution settings through the Web interface when the connection to the GV-VMS is
interrupted.
Note for Recording
1. By default, the images are recorded to the memory cards inserted in the GV-SV48000.
Make sure the Record to the local storage always as a secondary backup option is
enabled in Monitoring Settings. If this option is disabled, the camera will stop recording
to the memory card while the live view is accessed through Web browsers or other
applications.
2. Mind the following when using a memory card for recording:
•Recorded data on the memory card can be damaged or lost if the data are accessed
while the camera is under physical shock, power interruption, memory card
detachment or when the memory card reaches the end of its lifespan. No guarantee is
provided for such causes.
•The stored data can be lost if the memory card is not accessed for a long period of
time. Back up your data periodically if you seldom access the memory card.
•Memory cards are expendable and their durability varies according to the conditions
of the installed site and how they are used. Back up your data regularly and replace
the memory card annually.
•To avoid power outage, it is highly recommended to apply a battery backup (UPS).
•Replace the memory card when its read/write speed is lower than 6 MB/s or when the
memory card is frequently undetected by the camera.
•It is recommended to use Micro SD card of MLC NAND flash, Class 10 for optimal
performance.
i
Note for Installing Camera
When installing GV-SV48000, be sure that:
1. The camera is set up above the junction box to prevent water from entering the camera
along the cables.
2. Any PoE, power, audio and I/O cables are waterproofed using waterproof silicon rubber
or the like.
3. The screws are tightened and the cover is in place after opening the camera cover.
Note for Silica Gel Bags
1. The silica gel bag loses its effectiveness when the dry camera is opened. To prevent the
lens from fogging up, use the supplied adhesive tape and replace the silica gel bag every
time you open the camera, and conceal the gel bag in the camera within 2 minutes of
exposing to open air.
2. When the camera is shipped, a silica gel bag will be included inside the camera. For
first-time users, replace the silica gel bag prior to the installation to avoid foggy live view.
ii
iii
Optional Accessories
Optional devices can expand the capabilities and versatility of your camera. Contact our sales
representatives for more information.
Name Details
GV-PA901
Power over Ethernet (PoE)
Adapter
The GV-PA901 is a Power over Ethernet (PoE) adapter
designed to provide power to the IP device through a single
Ethernet cable to the GV-SV48000 camera.
GV-Mount Accessories The GV-Mount Accessories provides a comprehensive lineup
of accessories for installation on ceiling, wall and pole. For
details, see GV-Mount Accessories Installation Guide online.
1. Introduction
Welcome to the GV-SV48000 Quick Start Guide. In the following sections, you will learn the
basic installations and configurations of GV-SV48000. For the settings on the Web interface
of GV-SV48000, see GV-IP Camera Firmware Manual.
1.1 Packing List
1
•GV-SV48000
•GV-Mount103-1 (Bracket, Cap, Tube)
•RJ-45 Connector
•Hex Wrench
•Silica Gel Bag
•Download Guide
•Warranty Card
1.2 Overview
4
2
1
6
3
5
No. Name Function
1 Lens Receives image input.
2 Infrared LED Flashes red upon successful load default.
3 Default button Push and hold to load default. See section 7.2 Directly on the
Camera.
4 SD card slot Inserts a Micro SD card to store recording data.
5 Silica Gel Bag Keeps the camera dry.
6 Camera number Label for each individual camera.
2
2. Installation
GV-SV48000 can be mounted on the ceiling using the supplied Straight Tube Mount:
GV-Mount103-1. Make sure the ceiling has enough strength to support the camera and the
mount.
Required items:
•Screws for ceiling x 4 (Self-prepared)
•Micro SD card x 4 (Self-prepared)
•Screwdriver x 1 (Self-prepared)
Optionally extend with:
•GV-Mount702
1. Assemble GV-Mount103-1 by rotating the supplied mounting bracket, tube and mounting
cap together.
3
2. Make sure the tubes are properly screwed. Tighten the screws using the 2 mm hex key.
3. On the back of the camera, use a screwdriver to remove the 5 screws on the back plate
and remove the plate.
4. Insert a Micro SD card to each of the SD card slots. The labels correspond to the camera
numbers labeled on the back of the camera.
5. Replace 2 Silica Gel Bags in the marked area.
6. Close and secure the back plate.
7. Secure the safety lock to the back of the camera.
4
8. Thread the camera wires through the hole in the center of the mounting cap.
Andere Handbücher für GV Series
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere GeoVision Sicherheitskamera Handbücher
GeoVision
GeoVision GV-IP Speed Dome Bedienungsanleitung
GeoVision
GeoVision GV-SD2322-IR Bedienungsanleitung
GeoVision
GeoVision GV-EBD Series Bedienungsanleitung
GeoVision
GeoVision GV-IP Speed Bedienungsanleitung
GeoVision
GeoVision GV-FER12700 Bedienungsanleitung
GeoVision
GeoVision GV-IPCamera Series Bedienungsanleitung
GeoVision
GeoVision GV-BL8714 Bedienungsanleitung
GeoVision
GeoVision GV-BX2802 Bedienungsanleitung
GeoVision
GeoVision GV-IP Bedienungsanleitung
GeoVision
GeoVision GV-PTZ010D Bedienungsanleitung
GeoVision
GeoVision GV-EBD2702: GV-EBD4700 Bedienungsanleitung
GeoVision
GeoVision GV-EFER3700 Series Bedienungsanleitung
GeoVision
GeoVision GV-FD5300 Bedienungsanleitung
GeoVision
GeoVision GV-Hybrid LPR Camera 20R Bedienungsanleitung
GeoVision
GeoVision GV-EBX1100 Series Gebrauchs- und Pflegehandbuch
GeoVision
GeoVision GV-BX120D series Bedienungsanleitung
GeoVision
GeoVision GV Series Handbuch
GeoVision
GeoVision GV-LPR2800-DL Bedienungsanleitung
GeoVision
GeoVision GV-Fisheye GV-FE2301 Bedienungsanleitung
GeoVision
GeoVision GV-LPR Bedienungsanleitung
