GHM DeltaOHM LPUVA02 Bedienungsanleitung

Operating manual

UVA Radiometer

LPUVA02

www.deltaohm.com

English

Keep for future reference.

LPUVA02

- 2 -

V2.0

TABLE OF CONTENTS

INTRODUZIONE .................................................................................................... 3

WORKIN PRINCIPLE ........................................................................................... 4

INSTALLATION ..................................................................................................... 5

ELECTRICAL CONNECTIONS .................................................................................. 8

4.1

LPUVA02

CONNECTIONS

....................................................................................... 8

4.2

LPUVA02AC

CONNECTIONS

................................................................................... 9

4.3

LPUVA02AV

CONNECTIONS

................................................................................... 9

MEASUREMENT ................................................................................................... 10

5.1

LPUVA02 ...................................................................................................... 10

5.2

LPUVA02AC ................................................................................................... 10

5.3

LPUVA02AV ................................................................................................... 10

MAINTENANCE .................................................................................................... 11

TECHNICAL SPECIFICATIONS ............................................................................. 12

SAFETY INSTRUCTIONS ...................................................................................... 13

ACCESSORIES ORDERIN CODES ....................................................................... 14

LPUVA02

- 3 -

V2.0

1 INTRODUCTION

The LPUVA02 radiome er measures he global irradiance in he UVA spec ral range

on a fla surface (W/m

). Measured irradiance is he resul of he sum of direc solar

irradiance and of diffuse irradiance.

The radiome er can also be used for moni oring indoor UVA emissions.

Available in he following versions:

•LPUVA02: PASSIVE

•LPUVA02AC: ACTIVE wi h 4..20 mA CURRENT ou pu (0…200 W/m

)

•LPUVA02AV: ACTIVE wi h 0..1 or 0..5 or 0..10 V VOLTAGE ou pu o be de-

fined when ordering (0…200 W/m

Each radiome er is individually calibra ed a he fac ory and is dis inguished by i s own

calibra ion fac or. The calibra ion is performed by comparison wi h he primary s and-

ard of he Del a OHM me rology labora ory, using he emission line a 365 nm of a

sui ably fil ered Xe-Hg lamp.

Note: there is no international standard for the calibration of UVA radiometers; there-

fore, when considering the value of the calibration coefficient, the method by which it

was obtained must be taken into account; the same radiometer calibrated with differ-

ent procedures can have different calibration factors

LPUVA02

- 4 -

V2.0

2WORKIN PRINCIPLE

LPUVA02 radiome er is based on a solid s a e sensor, he spec ral ma ch wi h he de-

sired curve is ob ained using a special fil er. The rela ive spec ral response is repor ed

on figure 2.1.

Fig. 2.1

The radiome er is provided wi h a 50 mm ex ernal diame er dome in order o supply a

sui able pro ec ion of he sensor o he wea her agen s.

The response in accordance wi h he cosine law has been ob ained hanks o he par-

icular shape of he diffuser and of he housing. The devia ion be ween he heore ical

response and he measured one is shown in he Fig. 2.2.

Angle

Fig. 2.2

The excellen rela ion be ween he response of he radiome er and he cosine law al-

lows using he ins rumen also when he sun has a very low raising ( he UVA diffuse

radia ion increases as he sun moves away from he zeni h, herefore he error on he

direc radia ion, due o he imperfec response according o he cosine law, becomes

negligible on he measuremen of he global radia ion).

Rela ive spec

ral response

% devia ion from heore ica

l response

LPUVA02

- 5 -

V2.0

3INSTALLATION

Before ins alling he radiome er, refill he car ridge con aining silica-gel crys als. Silica

gel absorbs humidi y in he dome chamber and preven s, in par icular clima ic condi-

ions, condensa ion on he in ernal walls of he domes and measuremen al era ion.

Do no ouch he silica gel crys als wi h your hands while refilling he car ridge. Carry

ou he following ins ruc ions in an environmen as drier as possible:

1. Loosen he hree screws ha fix he whi e shade disk.

2. Unscrew he silica gel car ridge using a coin.

3. Remove he car ridge perfora ed cap.

4. Open he sache con aining silica gel (supplied wi h he radiome er).

5. Fill he car ridge wi h he silica gel crys als.

6. Close he car ridge wi h i s own cap, paying a en ion ha he sealing O-ring be

properly posi ioned.

7. Screw he car ridge o he radiome er body using a coin.

8. Check ha he car ridge is screwed igh ly (if no , silica gel life will be reduced).

9. Posi ion he shade disk and screw i wi h he screws.

10. The radiome er is ready for use.

The figure below shows he opera ions necessary o fill he car ridge wi h he silica gel

crys als.

Fig. 3.1: filling the silica-gel cartridge

Silica-gel

cartridge

Perforated cap

Sealed s

achet

of silica-gel crystals

Filling Closing the cartridge

LPUVA02

- 6 -

V2.0

•The radiome er mus be moun ed in an easy- o-reach loca ion in order o clean he

dome regularly and carry ou main enance. A he same ime, make sure ha no

buildings, cons ruc ions, rees or obs ruc ions exceed he horizon al plane where

he radiome er lies. If his is no possible, selec a si e where obs ruc ions in he

pa h of he sun from sunrise o sunse do no exceed 5 degrees of eleva ion.

•The radiome er mus be loca ed far from any kind of obs ruc ion, which migh re-

flec sunligh (or sun shadow) on o he radiome er i self.

•For fixing, use he holes on he radiome er body (remove he shade disk o access

he holes and reposi ion i af er moun ing) or he sui able accessories (see he fig-

ures below). In order o allow an accura e horizon al posi ioning, he radiome er is

equipped wi h a levelling device: he adjus men is made by means of he wo lev-

elling screws ha allow adjus ing he radiome er inclina ion. The mas heigh does

no exceed he radiome er plane o avoid measuremen errors caused by any re-

flec ion or shadow of he mas i self.

•I is preferably o hermally insula e he radiome er from i s moun ing bracke en-

suring, a he same ime, a good elec rical con ac o ground.

Fig. 3.2: fixing holes and levelling device

Fixing holes ∅ 6 mm

Levelling

device

LPUVA02

- 7 -

V2.0

HD2003.79K

HD2003.77C

HD2003.83

HD2003.83.1

HD2003.85K

Fig. 3.3: fixing accessories

LPUVA02

- 8 -

V2.0

4ELECTRICAL CONNECTIONS

LPUVA02… has a 4-pole connec or and uses he CPM12AA4... optional cables.

The metallic housing of the radiometer should preferably be

grounded ( ) locally. In this case, do not connect the wire of the

cable corresponding to the housing to prevent ground loops.

Only if it is not possible to ground locally the metallic case of the

radiometer, connect the wire of the cable corresponding to the

housing to ground. No e: in LPUVA02AV he housing is no connec ed

o he connec or.

4.1 LPUVA02

CONNECTIONS

The radiome er LPUVA02 is passive and does no require power supply. I is o be

connec ed ei her o a millivol me er or o a da a acquisi ion sys em. Typically, he ra-

diome er ou pu signal does no exceed 50 mV. In order o be er exploi he radiome-

er fea ures, he readou ins rumen should have 1 µV resolu ion.

Connector Function Color

1 +Vou Red

2 -Vou Blue

3 Housing (C) Whi e

4 Cable shield (SH) Black

+Vout

-Vout

Fig. 4.1: LPUVA02 connections

CPM12AA

…

ble

Radio

me er M12

male connec or

Da alogger or

conver er/amplifier

wi h V or mA ou pu

Connect to ground only if it is not possible to

ground locally the housing of the radiometer

LPUVA02

- 9 -

V2.0

4.2 LPUVA02AC

CONNECTIONS

The radiome er LPUVA02AC has 4…20 mA ou pu and requires 10…30 Vdc ex ernal

power supply. I is o be connec ed o a power supply and an ins rumen wi h 4…20

mA inpu as shown in fig. 4.2. The load resis ance of he ins rumen reading he signal

mus be ≤ 500 Ω.

Connector Function Color

1 Posi ive (Iin) Red

2 Nega ive (Iou ) Blue

3 Housing (C) Whi e

4 Cable shield (SH) Black

4...20 mA

34SH

Iin

Iout

Fig. 4.2: LPUVA02AC connections

4.3 LPUVA02AV

CONNECTIONS

The radiome er LPUVA02AV has 0…1 V, 0…5 V or 0…10 V ou pu (depending on he

ordered ou pu ) and requires ex ernal power supply: 10…30 Vdc for 0…1 V and

0…5 V ou pu s, 15…30 Vdc for 0…10 V ou pu . I is o be connec ed o a power sup-

ply and an ins rumen wi h vol age inpu as shown in fig. 4.3. The load resis ance of

he ins rumen reading he signal mus be

≥

100 kΩ.

Connector Function Color

1 Ou pu posi ive (+Vou ) Red

2 Ou pu nega ive

Power supply nega ive (GND) Blue

3 Power supply posi ive (+Vdc) Whi e

4 Cable shield (SH) Black

GND

+Vdc

+Vout

Fig. 4.3: LPUVA02AV connections

CPM12AA

…

ble

Radio

me er M12

male connec or

Power supply

Connect to ground only if it is not possible to

ground locally the housing of the radiometer

Ins rumen wi h

4…20 mA inpu

CPM12AA

…

ble

Radio

me er M12

male connec or

Power supply

Ins rumen

wi h

vol age inpu

LPUVA02

- 10 -

V2.0

5MEASUREMENT

Below are he ways o calcula e he irradiance.

5.1 LPUVA02

Each radiome er is dis inguished by i s own sensi ivi y (or calibra ion fac or) S ex-

pressed in µV/(Wm

-2

) and shown in he label on he radiome er (and in he calibra ion

repor ).

The irradiance E

is ob ained by measuring wi h a mul ime er he difference of po en ial

DDP a he ends of he sensor and applying he following formula:

= DDP / S

where:

is he irradiance expressed in W/m

;

DDP is he difference of po en ial expressed in µV measured by he mul ime er;

S is he sensi ivi y of he radiome er expressed in µV/(Wm

-2

5.2 LPUVA02AC

The 4…20 mA ou pu signal corresponds o 0…200 W/m

irradiance range.

The irradiance E

is ob ained by measuring wi h a mul ime er he curren I

out

absorbed

by he sensor and applying he following formula:

= 12.5

•

out

– 4mA)

where:

is he irradiance expressed in W/m

;

out

is he curren expressed in mA absorbed by he radiome er.

5.3 LPUVA02AV

The ou pu signal (0…1 V, 0…5 V or 0…10 V depending on he version) corresponds o

0…200 W/m

irradiance range.

The irradiance E

is ob ained by measuring wi h a mul ime er he ou pu vol age V

out

he sensor and applying he following formula:

= 200

•

out

for he version 0…1 V

= 40

•

out

for he version 0…5 V

= 20

•

out

for he version 0…10 V

where:

is he irradiance expressed in W/m

;

out

is he ou pu vol age expressed in V measured by he mul ime er.

Inhaltsverzeichnis

Andere GHM Messgerät Handbücher

GHM

GHM GREISINGER G 1500 Bedienungsanleitung

GHM

GHM GREISINGER G 1910 Series Bedienungsanleitung

GHM

GHM Delta OHM PYRAsense LPS03 Series Bedienungsanleitung

GHM

GHM DeltaOHM LPPYRA-Lite Bedienungsanleitung

GHM

GHM DeltaOHM HD2301.0 Bedienungsanleitung

GHM

GHM Delta OHM HD3405.2 Bedienungsanleitung

GHM

GHM GREISINGER RS PRO RS MH 3161-002-ex Bedienungsanleitung

GHM

GHM Delta OHM PYRAsense LPS02 Series Bedienungsanleitung

GHM

GHM GREISINGER G 1111 Bedienungsanleitung

GHM

GHM GREISINGER GMH 3331 Bedienungsanleitung

GHM

GHM GREISINGER G 1910 Series Bedienungsanleitung

GHM

GHM GREISINGER G 1000 Series Bedienungsanleitung

GHM

GHM Delta OHM HD2304.0 Bedienungsanleitung

GHM

GHM Martens BA 24N2 Series Bedienungsanleitung

GHM

GHM Delta OHM PYRAsense LPS10 Series Bedienungsanleitung

GHM

GHM GREISINGER GMI 15 plus Bedienungsanleitung

GHM

GHM Delta OHM LPPYRA12 Bedienungsanleitung

GHM

GHM G 1410 Bedienungsanleitung

GHM

GHM Delta OHM HD32.3TC Bedienungsanleitung

GHM

GHM GREISINGER G 1110 Bedienungsanleitung

GHM

GHM Delta OHM LPPYRA11 Bedienungsanleitung

GHM

GHM DeltaOHM LPPHOT01 Bedienungsanleitung

GHM

GHM Delta OHM HD2114P.0 Bedienungsanleitung

GHM

GHM Delta OHM HD2303.0 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung