Global Sat GB-1000 Bedienungsanleitung
1.
Power On/O
(hold 3 sec.)
or Backlight
4.
OK/Setup or
Pause (in training)
2.
Page Down
3.
Page Up
GB-1000 User Manual
v2.0
4.
O
K
/
Pa
u
Q1. How to start training and check your training data?
[Power On]
3 sec. [OK]
current timeof day
* AVERAGE SPEED TOTAL ACCUMULATED DISTANCE * TRIP DISTANCE TRIP TIME
* MAXIMUM SPEED CALORIES
** MAXIMUM CADENCE ** AVERAGE CADENCE ** CURRENT CADENCE
The satellite icon will flash while locating.
BLUE arrow means [Page Up]
RED arrow means [Page Down]
* If speed/cadence combo sensor is not connected, speed and distance will be calculated by GPS.
** only when speed/cadence combo sensor is connected
Q2. How to configure and pair your device?
[OK]
3 sec. [OK]
[Page Down] or [Page Up] to
select gender
[OK]
[Page Down] or [Page Up] to
adjust height
[OK]
[Page Down] or [Page Up] to
adjust age
[OK]
[OK]
[OK]
[Page Down] or [Page Up] to
switch time mode
[Page Down] or [Page Up] to
select language
[OK]
[Page Down] or [Page Up] to
adjust weight
[Page Down] or [Page Up] to
swap unit system.
[Page Down] or [Page Up]
to adjust time zone [OK]
[Page Down] or [Page Up] to adjust
wheel size
Metric: mm
English: inch
[OK]
Please enter configuration
mode at START page.
[Page Down] / [Page Up]
[OK]
Speed/Cadence icon will flash while
pairingSpeed/Cadence sensor.
Speed/Cadence
combo sensor pairing
success?
Yes
No
[OK]
[OK]
Go back
to START
page
[OK]
Speed/Cadence
combo sensor
pairing process
When turning on, device will discover and connect previous paired
Speed/Cadence automatically.
[Page Down]
3 sec.
No
waypoint can only be saved when GPS is located
Yes
[Page Down] /
[Page Up]
[OK] [OK]
You cannot save one waypoint
if GO-TO function is in use.
A3 Step 1: Save Waypoint
A3 Step 2: Guide to Waypoint (GO-TO function)
save waypoint?
Yes
[Page Up]
3 sec.
No Yes
[Page Down] /
[Page Up]
[OK]
[Page Down] /
[Page Up]
[OK]
cancel Go-To
exit Go-To
No
activate GO-TO function
Q3.1. What does GO-TO function mean?
A3.1: GO-TO function can guide you to the saved waypoint by pointing the direction.
When you are close enough to the saved waypoint (within 20 m), device will show
“GOAL ARRIVED ”.
GPS fixed ?
You can save only “one” waypoint on this device and previous waypoint will be replaced by
new waypoint.
Q3. How to use GO-TO function?
skip waypoint saving?
[OK]
return to Go-To mode
Waypoint
exists?
Go-To
in use?
[OK]
[Page Down]
& [Page Up]
3 sec.
[OK/Setup] to
re-confirm
Total Distance
Reset
[Page Down] / [Page Up]
[OK/Setup]
to reset
Total Distance
to zero
[OK/Setup]to
re-confirm Factory Reset
[Page Down]
[Page Down]
[Page Down] / [Page Up]
[OK/Setup] to
cancel reset
action and
go back
Start page
Press
“OK/Setup”
to do
Factory Reset
[Page Down]
[Page Down] and go
back to Total
Distance Reset
[OK/Setup]to exit and go
back to Start page
You can only reset
at start page.
Q4.1. What does total distance reset mean?
A4.1: “TOTAL DISTANCE RESET” will reset the total accumulated distance to zero.
Q4.2. What dose factory reset mean?
A4.2: “FACTORY RESET” will reset all settings to original factory values.
TOTAL DISTANCE RESET?
FACTORY RESET?
[OK/Setup] to
cancel reset
action and
go back
Start page
Q4. How to do total distance reset and factory reset?
[OK/Setup]to
re-confirm
Total Distance
Set
[OK/Setup]
to set
TotalDistance
TOTAL DISTANCE SET?
[OK/Setup] to
cancel set
action and
go back
Start page
[Page Down] / [Page Up]
[OK/Setup]
to do Total
DistanceSet
[Page Down] /
[Page Up] to
adjust Total
Distance
Q6. Other questions
A5: Hold [Power On/Off] for 8 seconds to do hardware shutdown and then turn on again to
reboot the device.
Q5. How to reboot the device?
Q6.1. How to pause during your training?
A6.1: Just press [OK/Setup] when you are in training and current training status
will be held. When system is pausing, the upper speed area will show “
P” and you can still check current training status by pressing [Page Down]
/ [Page Up].
Q6.2. How to save training data?
A6.2: Training data will be saved while turning off the device. You must turn on
the device to start a new training.
Q6.3. How to activate compass function?
A6.3: To activate compass function, device must be in motion with GPS located.
(When GO-TO function is in use, compass function will be disabled and
the “N” character in compass area will not be shown.)
Q6.4. How to charge your device?
A6.4: You can charge your device by plugging in USB/Power cable and display
will show “FULL” when charging completes. While plugging in USB/Power
cable, you will be forced to leave training mode and your training data will
be saved immediately.
Connect to PC
via USB Cable
Trip will be saved automatically.
After communicating
with PC software
Any Mode
Q7. Where to download the “Training Gym Pro” PC software?
Q8. How to connect device to PC software?
A7: You can visit our official website “http://www.globalsat.com.tw/” and search “GB-1000” to
download from product page.
Q7.1. What can PC software do?
A7.1: PC software can help you check your training data by showing training files, training
information, data graphs...etc.
Please make sure you have installed the USB driver before connecting to PC software. (Please
check our official website “http://www.globalsat.com.tw/” and search “GB-1000” for details about
USB driver installation. )
Training Gym Pro PC Software Screenshot
[Page Down] / [Page Up]
[OK/Setup]to
re-confirm
Total Distance
Reset
Start PC
software
Connect
device and PC
via USB cable
Choose “Configuration /
Firmware Upgrade” in PC
SW to start the process
device is off UPGRADE FIRMWARE?
PC MODE
[OK]
Q9. How to upgrade system firmware?
Q10.
How do I know how long the recording time remains?
Q11. How to check firmware version?
[OK/Setup]to
re-confirm
Total Distance
Reset
Turn on device by
holding [Page Up] & [OK]
then [Power On]
unplug USB cable
when process completes
9.1 You can leave firmware upgrade process by pressing [Power On/Off] for 3 sec. before PC
software starts “Configuration / Firmware Upgrade”.
9.2 If you encounter any interruption during firmware upgrade process, please press [Power
On/Off] for 3 sec. to turn off the device. Then, press [Page Up], [OK] & [Power On] to redo
firmware upgrade process.
9.3 Your training files, system configuration and total distance will be kept after firmware upgrade.
A10: System will show the recording time remaining in HOUR : MINUTE
format when you turn on/off the device. (ex: 2 hours and 11 minutes
left) Besides, you can also press [Page Up] in “START”page to see
the recording time remaining (keep pressing [Page Up] three times in
this page to go back to “START”page). Moreover, when there is no
memory space left, system will show “NO MEMORY”every one
minute to warn you while you are in training.
A11: Press [Page Up] two times in “START”page and you can see the
firmware version. (ex: version 1308261) You can go back to
“START”page by pressing [Page Up] two times in this page.
GB-1000
Andere Global Sat GPS Handbücher
Global Sat
Global Sat ET-212 Betriebshandbuch
Global Sat
Global Sat TR-600 Bedienungsanleitung
Global Sat
Global Sat TR-151 Bedienungsanleitung
Global Sat
Global Sat GD-101 Bedienungsanleitung
Global Sat
Global Sat TR-151A Bedienungsanleitung
Global Sat
Global Sat ND-100S Bedienungsanleitung
Global Sat
Global Sat ET-318 Bedienungsanleitung
Global Sat
Global Sat GD-102 Bedienungsanleitung
Global Sat
Global Sat BT-821C Bedienungsanleitung
Global Sat
Global Sat ER-506 Bedienungsanleitung
Global Sat
Global Sat GV-370 Bedienungsanleitung
Global Sat
Global Sat ST-100 Series Bedienungsanleitung
Global Sat
Global Sat GV-201 Bedienungsanleitung
Global Sat
Global Sat LW-360HR Bedienungsanleitung
Global Sat
Global Sat BTT-100 Bedienungsanleitung
Global Sat
Global Sat ET-314AC Bedienungsanleitung
Global Sat
Global Sat ET-112 Bedienungsanleitung
Global Sat
Global Sat BU-353 Bedienungsanleitung
Global Sat
Global Sat ND-105X Bedienungsanleitung
Global Sat
Global Sat BR-355 Bedienungsanleitung
