GOEBEL GO-BR1 Bedienungsanleitung
User Manual
innovative fastener solutions
GO - BR1
GO - BR2
GO - TR1
Cordless Blind Rivet Battery Tool
2| Deutsch1| English
User Manual: GO-BR1 / GO-BR2 / GO-TR1
Table of contents
www.goebel-group.com
Page
Safety precautions 2 - 4
Daily maintenance & environmental protection 4
1. Machine overview
1.1 Capacity
1.1 Technical parameters
1.2 Conguration/ Accessories (see g. A)
1.3 Parts List (see g. B)
1.4 GO-BR series tool parts list
4
5
5
5 - 6
7
8
2. Preparation of the tool
2.1 Changing the mouthpiece
2.2 Changing the jaws
2.3 Other spare parts
2.4 Battery check
2.5 Checking the tool
9
9
9
10
10
10
3. Function settings
3.1 Setting the stroke
3.2 Setting the riveting mode
11
11
11
4. Tool operation
4.1 Riveting in conventional mode (D)
4.2 Rivets in self-locking mode (S)
12
12
12
5. Charger & Batteries
5.1 Technical parameters
5.2 Charger usage
5.3 Battery usage
13
13
13
13
6. FAQ (Questions / Answers) 14
7. Troubleshooting
7.1 Failfunction
7.2 Probable cause
7.3 Correction of defects
14
14
14
14
8. Protection conditions & CE certication 15
Deutsch | 2English | 2
To reduce the risk of electric shock, personal injury, re and property damage, be sure
to observe the following safety precautions.
Description of the symbols:
www.goebel-group.com
Safety precautions
Danger
Indicates imminent hazards which, if not avoided will result in serious injury or death
Warning
Indicates potential hazards which, if not avoided could result in serious injury or death
Caution
Indicates potential hazards which, if not avoided may result in minor injury or loss of property
The following characters are used to classify and describe the types of description to
be followed.
This sign is used to alert the user to the prohibited action steps.
This sign is used to draw users' attention to the operating steps that must be
carried out to use the appliance.
• This tool is limited to riveting holes and must not be used for percussion or other
purposes, such as a hammer.
• Please do not carry out riveting without sheet material! Make sure to mount and
tighten the remaining rivet mandrel catcher to prevent remaining rivet mandrels from
ying out and causing injuries!
• Do not overload the riveting tool. Please use it within the range specied in the Set-
tings function (see P10).
• Do not block the venting of the motor. Do not insert any objects into the vent.
• It is recommended to wear safety glasses and personal protective equipment when
using this tool e.g. gloves, hard hat, safety shoes, noise-insulating earplugs and fall
protection devices and other necessary protective measures.
Please keep the packaging boxes and accessories and handle them with care.
• The tool and accessories should be placed in the plastic case, stored in a dry place
and out of the reach of children.
Caution
2| Deutsch3| English
Safety precautions
www.goebel-group.com
Use of the battery
• Do not charge damaged, contaminated or wet batteries.
• Batteries must not be thrown into water or re at any time, and used batteries must
not be disposed of at will.
• Do not charge when the ambient temperature is below 0°C or above 45°C.
Use of the charger
• The original battery and the manufacturer's charger must be used for charging.
• The battery must not be charged with a damaged, dirty or damp charger.
• Do not place metal objects in the charging area as a short circuit may occur.
• This charger must not be used by persons with disabilities, mental disabilities or
persons without training or knowledge unless a safety ofcer is on site to supervise
or instruct them in the use of the charge.
Danger
• Do not use the riveting tool in a damp environment or near ammable liquids and
gases. Risk of explosion!
• Do not point the riveting tool at yourself, others or animals.
• Do not load in a damp environment, near an open re or in an environment with
ammable, highly combustible gases that can easily be detonated.
Warning
• Tools should be placed so that they do not fall down to avoid unnecessary damage
and safety accidents.
• When installing the battery, make sure to x its position. An audible "click" sound will
indicate that the battery is in place.
• When servicing this riveting tool, the battery must be removed.
• Before charging, check that the charger and its power supply equipment are in good
condition.
• Use a power supply unit that matches the charger.
• Plugs, power cords and chargers should be checked regularly. If a problem is found, it
should be repaired by qualied maintenance personnel.
• Maintenance personnel must have professional skills; only qualied professionals
can carry out repairs. If in doubt, please return the unit to the authorised dealer or
manufacturer for repair.
• Original spare parts must be used during maintenance.
Deutsch | 2English | 4
www.goebel-group.com
Maintenance
• Regular maintenance prolongs the life of tools with a lithium battery and should be
carried out by an authorised dealer or manufacturer. In case of more frequent use, it
is recommended to carry out maintenance in advance.
• Maintenance of the riveting tool is limited only to replacement of worn parts and
quick wear parts. (see Pg.8 for replacement accessories).
• To keep the tools in good working condition, please check the wear parts of the tools
frequently. In case of wear or damage, please contact the dealer for purchase.
Repair
• The warranty period is 1 year from the date of sale. Excluded from this are quick wear
parts noted on page 8.
• Failure to comply with the relevant installation and commissioning instructions or
failure to follow the operating procedures may void the warranty.
Environmental protection and resource recovery
• When replacing lithium batteries used in this product, be sure to observe the following
points:
• If your country or region has regulations, please be sure to take the old battery to a
professional company for disposal.
• Do not throw old batteries into the trash, re or water!
1. Machine overview
1
2
3
4
5
6
7
8
9
10
1
2
3
4
5
6
7
8
9
10
Component name
Screw cap
Nosepiece
Front Sleeve Set
Function display
Battery
Mandrel collector
Tool body
LED light
Trigger
Charger
2| Deutsch5 | English
www.goebel-group.com
1.1 Capacity / Technical Parameters
260
1057.6599
21.5
GO-BR1 / GO-TR1 GO - BR2
9.72 10.2 2.17
9.8
2.68
1.46
3.62
2.36
0.9
1.77
3.62
2.52
2.52
1.89
0.85
Model GO-BR1 GO-BR2 GO-TR1
Motor 18V Brushless motor
Noise level < 78dB
Traction power 2700lbft 4000lbft 2700lbft
Stroke 0.83" 1.0" 1.0"
Net weight (incl. battery) 3.17 lbs 3.53 lbs 3.17 lbs
Capacity Ø 1/8" - 3/16" Ø 5/32" - 1/4" Ø 3/16", 1/4", 9/32"
Material specication All materials Blind rivets All materials High Strength
Blind Rivet
Aluminium
Triple Claw Blind Rivet
1.2 Conguration / Accessories (g. A)
(g. A)
1.77
Deutsch | 2English | 6
www.goebel-group.com
1.2 Conguration / Accessories (g. A)
NO Parts description Code Spec Qty. NO Parts description Code Spec Qty.
2Screw cap
2277010210
1 14 ABS case
2277013310
1
3Rubber ring
2277010310
1 15
Battery Li-Ion 18V 2.0 Ah
2277012410
2
10 Mandrel Collector
2277011610
1 16 Battery Charger
2277012510
1
13 Wrench
2277012310
1
NO Parts description Code Spec Qty. NO Parts description Code Spec Qty.
1Nosepiece D 3/16"
2277010110
Ø 3/16" 1 8 Push Pin Set
2277010810
1
4Front Sleeve Set
2277010410
1 9
Battery Li-Ion 18V 2.0 Ah
2277012410
1
5Clamping Sleeve
2277010510
1 11 Nosepiece B 1/8"
2277012210
Ø 1/8" 1
63-jaw set
2277010610
1 12 Nosepiece C 5/32"
2277012110
Ø 5/32" 1
7
Clamping jaw pusher
2277010710
1
GO - BR1 Conguration
NO Parts description Code Spec Qty. NO Parts description Code Spec Qty.
1a Nosepiece F .236"
2277010120
Ø .236" 1 17 Nosepiece E 1/4"
2277012620
Ø 1/4" 1
4b Front Sleeve Set
2277010410
1 *18 Nosepiece K for
H-Lock 1/4"
2277012720
Ø 1/4" 1
5Clamping Sleeve
2277010510
1 *19 Nosepiece J for
M-Lock 1/4"
2277012820
Ø 1/4" 1
6a large 3-jaw set
2277010620
1 *20 Nosepiece H for
H-Lock 3/16"
2277012920
Ø 3/16" 1
7
Clamping jaw pusher
2277010710
1 *21 Nosepiece G for
M-Lock 3/16"
2277013020
Ø 3/16" 1
9Push-pin spring
2277010910
1 *22 3-jaw set
2277010610
1
12 Nosepiece C 5/32"
2277012110
Ø 5/32" 1Important note: Serial numbers 18-22 are optional accessories.
GO - BR2 Conguration
NO Parts description Code Spec Qty. NO Parts description Code Spec Qty.
1b Nosepiece for
TRE-GO 9/32"
2277020110
Ø 9/32" 1 8 Push Pin Set
2277010810
1
4Front Sleeve Set
2277010410
1 9 Push-pin spring
2277010910
1
5Clamping Sleeve
2277010510
111a Nosepiece for TRE-
GO 3/16"
2277022110
Ø 3/16" 1
6large 3-jaw set
2277010620
112a Nosepiece for TRE-
GO 1/4"
2277022210
Ø 1/4" 1
7
Clamping jaw pusher
2277010710
1
GO - TR1 Conguration
* General conguration
2| Deutsch7| English
www.goebel-group.com
Fig. B
1.3 Parts List (g. B)
Deutsch | 2English | 8
www.goebel-group.com
1.4 GO-BR series tool parts list Fig.B
NO Standard Code Parts description Qty. NO Standard Code Parts description Qty.
2 2277010210 Screw cap 1 18 2277011810 Trigger 1
3 2277010310 Rubber ring 1 19 2277011910 Trigger spring 1
13 2277011310 Tool body screw 1 23 2277012310 Wrench 1
14 2277011410 Tool Body GO-BR 1 24 2277012410 Battery Li-Ion 18V 2.0 Ah 1
15 2277011510 Mandrel release component 1 25 2277012510 Battery Charger Set 1
16 2277011610 Mandrel Collector 1
*Please note that the shaded parts in the list are wear parts, serial numbers 11, 12, 17 are structural parts, the. Serial Nos. a, b are
their own exclusive parts for tools, and the rest are general parts. Serial numbers *27-*31 are optional accessories.
List of common parts: GO-BR1, GO-BR2, GO-TR1
NO Standard Code Parts description Qty. NO Standard Code Parts description Qty.
1 2277010110 Nosepiece D 3/16" 1 10 2277011010 Spring Sleeve Set 1
4 2277010410 Front Sleeve Set 1 11 2277011110 Gear Box Set 1
5 2277010510 Clamping Sleeve 1 12 2277011210 Brushless Motor 1
6 2277010610 3-jaw Set 1 17 2277011710 PCB-Set 1
7 2277010710 Clamping jaw sleeves 1 20 2277012010 Function display/setting 1
8 2277010810 Push Pin Set 1 21 2277012110 Nosepiece C 5/32" 1
9 2277010910 Push-pin Spring 1 22 2277012210 Nosepiece B 1/8" 1
GO-BR1 parts list
NO Standard Code Parts description Qty. NO Standard Code Parts description Qty.
1a 2277010120 Nosepiece F .236" 1
17b
2277011720 PCB-Set 1
4b 2277020310 Front Sleeve Set 1 20 2277012010 Function display/setting 1
5 2277010510 Clamping Sleeve 1 21 2277012110 Nosepiece C 1
6a 2277010620 Large 3-jaw set 1 26 2277012620 Nosepiece E 1
7 2277010710 Clamping jaw sleeves 1 *27 2277012720
Nosepiece K (Premium/ H-Lock 1/4")
1
9 2277010910 Push-pin spring 1 *28 2277012820 Nosepiece J for M-Lock 1/4" 1
10 2277011010 Spring Sleeve Set 1 *29 2277012920
Nosepiece H (Premium/ H-Lock 3/16")
1
11b
2277011120 Gear Box Set 1 *30 2277013020 Nosepiece G for M-Lock 3/16" 1
12a
2277011220 Brushless Motor 1 *31 2277010610 3-jaw Set 1
15b
2277022010 Mandrel release component 1
GO-BR2 parts list
NO Standard Code Parts description Qty. NO Standard Code Parts description Qty.
1b 2277020110 Nosepiece for TRE-GO 9/32" 1 10 2277011010 Spring Sleeve Set 1
4 2277020310 Front Sleeve Set 1 11 2277020210 Gear Box Set 1
5 2277010510 Clamping Sleeve 1 12 2277011210 Brushless Motor 1
6 2277010610 3-jaw Set 1
15b
2277022010 Mandrel release component 1
7 2277010710 Clamping jaw sleeves 1 17 2277011710 PCB-Set 1
8 2277010810 Push Pin Set 1
21a
2277022110 Nosepiece for TRE-GO 3/16" 1
9 2277010910 Push-pin spring 1
22a
2277022210 Nosepiece for TRE-GO 1/4" 1
GO-TR1 parts list
2| Deutsch9| English
www.goebel-group.com
2. Tool preparation
Danger
Before replacing the damaged parts, such as the nosepieces or clamping jaws, you
must rst remove the battery from the tool.
Failure to remove the battery rst may result in injury or property damage.
Select a nosepiece that meets the rivet specication or other parts that need to be
replaced (see the following illustration).
Read the following special tips carefully before using the riveting tool:
• Make sure that the battery has been removed from the tool as shown.
2.1 Changing the mouthpiece
• According to gure ➀ , loosen the nosepiece with a wrench in the direction of the arrow
and unscrew the nosepiece.
• According to the illustration ➅ , screw the nosepiece that needs to be replaced with a
wrench in the direction of the arrow and tighten the nosepiece.
2.2 Changing the jaws
• According to gure ➁, loosen the screw cover with a wrench in the direction of the
arrow and unscrew the screw cover. According to gure ➂, loosen the clamping sleeve
with a spanner in the direction of the arrow and unscrew the clamping sleeve.
• Replace the three clamping jaws and other parts as shown in the following gure.
• According to gure ➃,➄, turn the clamping sleeve and screw cap in the direction of the
arrow and tighten them with a spanner, then simply charge the battery.
Andere Handbücher für GO-BR1
1
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere GOEBEL Nietwerkzeuge Handbücher
