Graco Angelcare 1750296 Bedienungsanleitung

Micro.

Tic/Alarm

Low Batt.

Movement Sensor With Sound Monitor

OWNER'S MANUAL

KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

This device is designed to aid in the

monitoring of your child. When using the

monitor, you must still provide the supervision

necessary for the continued safety of your

child. This product is not designed

or intended for use as a medical monitor.

Always be sure that both the transmitter and

receiver are working properly and are within

range of each other.

• STRANGULATION HAZARD. Keep the

adapter cords out of the reach of children.

Do not use with extension cords.

• DO NOT place the Nursery Unit or its cord

within your child’s reach. Do not put the

Nursery Unit inside a crib or playard.

• Use ONLYwith 110-120 voltAC electrical

outlets.

• Protect theAC adapter cords. Place them

so they are not walked on or pinched by

furniture or other items.

•Allow for proper ventilation when units are in

use. Do not cover the Nursery Unit or

Parent Unit with any object such as a

blanket. Do not place it in a drawer or in any

location which would mufﬂe the sound or

interfere with the normal ﬂow of air.

•DO NOT immerse any part of the Nursery

Unit or Parent Unit in water. Clean only with a

dry cloth.

• DO NOT place unit near water and

moisture. Do not use the Nursery Unit

outdoors. Do not use the Nursery Unit near

possible wet areas, such as a bathtub,

shower, wash basin, sink, laundry tub,

swimming pool, wet basement, etc.

• Keep Nursery Unit away from heat sources,

such as ﬁreplaces, radiators, stoves, and TVs

or other appliances. Heat can damage the

case or electrical parts.

WARNING: This product is not a toy.

• Do not use the Nursery Unit if:

• The adapter cords or plugs have been

damaged.

• The unit has been exposed to liquids.

• Unit has been dropped or is damaged.

• DO NOT OPEN THE NURSERY UNIT,

PARENT UNIT ORADAPTERS.

No user-serviceable parts inside. Risk of

electrical shock, ﬁre or death.

• The antenna used for this transmitter must

be installed to provide a separation distance

of at least 20 cm (7.9”) from all persons and

must not be co-located or operating in

conjunction with any other antenna or

transmitter.

Charge the batteries for 15 hours prior to ﬁrst

use. Be sure to have the monitor in the OFF

position during this period. Only use theAC

adapters included with your monitor.

DO NOT use these adapters with any other

equipment.

• When unplugging theAC adapter from the

nursery unit, be sure it is switched to the off

position. If it isn’t, the unit will revert to

battery mode if batteries are installed.

• You can use rechargeable batteries in

the Nursery Unit, however, they will not be

recharged by plugging in theAC adapter.

To recharge, remove the batteries and use an

external charger.

Failure to follow these warnings and the assembly instructions

could result in serious injury or death.

• This product is NOTa substitute for direct

supervision of your baby. Check your baby’s

activities at regular intervals. Monitoring of

premature babies, or those considered to be

at risk, should always be carried out under

the supervision of a health professional.

•Always place both the Nursery Unit and

Parents’Unit on a ﬂat surface in an upright

position and allow for proper ventilation.

•Avoid damage to the Sensor Pad cord and

to the adapter cords. Route cords so that

they are not likely to be walked on or pinched

by items placed on or against them.

• Route sensor pad cord only below crib

matress and out of reach of children.

• Use ONLYAAA(LR03) batteries (not

included) and/or theAC adapters provided for

the Parents’Units.

• During long periods of non-use remove all

batteries from their compartments and unplug

theAC adapters.

• This monitor uses public airwaves to

transmit signals. The Parents’Unit may pick

up signals or interference from other nursery

monitors in your area. Your monitor may even

be picked up by other households. To protect

your privacy, make sure both units are turned

off when not in use. If you experience

interference, change the channel on both

units.

• When the monitor is in use, do not use a

crib mobile or other crib accessories that may

produce vibrations. Other sources of

vibrations may include fans, washing

machines, loud music, etc. These sources of

vibration may interfere with the performance

of yourAngelcare® monitor and the alarm

will not sound if it continues to detect any

movement other than your baby’s. Be sure all

vibration sources are eliminated before using

the monitor.

• You may experience false alarms for

several reasons. The most common reason is

the Nursery Unit has not been turned off after

you have removed your baby from the crib.

Another reason is the Sensor Pad has not

been placed under the mattress properly. Be

sure the Sensor Pad is on a ﬂat, ﬁrm surface

with the turquoise side facing up.

The sensitivity level may also need to be

adjusted. Refer to the Movement Sensitivity

Adjustment section on Pg. 11.

•Always be sure to immediately check on

baby whenever an alarm sounds.

• Your monitor can be used in any crib that is

stationary and designed to safely hold a baby.

If your crib has a spring or slat base you will

need to place a piece of Masonite board

under the Sensor Pad. This support must be

at least 13 inches long on all four sides and

1/4 inch thick. Only use yourAngelcare®

monitor in a stationary sleeping environment

such as a crib where the Sensor Pad can rest

on a completely ﬂat, ﬁrm surface.

WARNING

Modiﬁcations not authorized by the

manufacturer may void users authority to

operate this device.

NOTE: This equipment has been tested and

found to comply with the limits for a Class B

digital device, pursuant to Part 15 of the FCC

Rules.

These limits are designed to provide

reasonable protection against harmful

interference in a residential installation. This

equipment generates, uses and can radiate

radio frequency energy and, if not installed

and used inaccordance with the instructions,

may cause harmful interference to radio

communications.

However, there is no guarantee that

interference will not occur in a particular

installation. If this equipment does cause

harmful interference to radio or television

reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference

by one or more of the following measures:

• Reorient or relocate the receiving

antenna.

• Increase the separation between the

equipment and receiver.

• Connect the equipment into an outlet on a

circuit different from that to which the receiver

is connected.

• Consult the dealer or an experienced radio/

TV technician for help.

This device complies with part 15 of the FCC

Rules. Operation is subject to the following

two conditions:

(1) This device may not cause harmful

interference, and

(2) This device must accept any interference

received,including interference that may

cause undesired operation.

Volume

Control

Antenna

Power Indicator (Solid Green)

Low Battery Indicator (Flashes Orange)

Power Switch/Channel Selector

Sound Lights

Speaker

Battery Compartment

AC Adapter Jack

FRONT

BACK

Antenna

Microphone

Movement Indicator (Flashes Green)

Alarm Indicator (Flashes Red)

Poor Movement Indicator

(Flashes Orange)

Power Switch/

Channel Selector

Power Indicator (Solid Green)

Low Battery Indicator

(Solid Orange)

Movement Sensitivity

Adjustment

Sensor Pad Jack

AC Adapter Jack Battery

Compartment

Alarm Sounder

Function Selector

FRONT

BACK

Features

Parent Unit

Nursery Unit

AC ADAPTER

AC ADAPTER Extra Parent Unit

and adapter

(On certain models)

Installing Batteries in Parent Unit

To insert batteries, remove the battery cover on the bottom of

the unit.

Parents Unit

Unité des parents

The Parents’ Unit requires four AAA (LR03)

batteries (not included). To insert batteries, remove the battery

cover on the back of the unit and insert the batteries matching

positive (+) to positive (+) and negative (-) to negative (-) and

replace the battery cover.

Replace the batteries when the Low Battery Indicator

flashes and turns orange instead of green.

IMPORTANT: Charge the batteries for 15 hours prior to first

use. Be sure to have the monitor in the OFF position during

this period.

Only use the AC adapters included with your monitor. Do not

use these adapters with any other equipment.

Insert the AC adapter into the jack marked “9V (6LR61)” and

plug the adapter into an electrical outlet. Unit will run off of the

AC adapter unless there is a power outage, in which case the

unit will begin using the batteries.

IMPORTANT: Use only the AC adapters included with your

monitor. Do not use these adapters with any other

equipment.

















































































Sound &

Movement

Sound

Only

Tic O

Sensor Pad

Sensitivity

Nursery

Unit

Model #AC201

Installing Batteries in Nursery Unit

Replace the battery cover. Replace the batteries when the Low

Battery Indicator turns orange and a rapid ticking is heard. If

the batteries are not replaced, the light will eventually turn red

and the monitor will stop working.

The Nursery Unit requires four AAA (LR03) alkaline or

rechargeable batteries (not included). Rechargeable batteries

can be used but they will NOT be recharged in the Nursery

Unit by plugging in the AC adapter. They will have to be

removed and recharged in an external charger.

To insert batteries, remove the battery cover on the back of the

unit.

Insert the batteries matching positive (+) to positive (+) and

negative (-) to negative (-) Replace the battery cover.

Insert the AC adapter into the jack marked “9V” and plug the

adapter into an electrical outlet. Unit will run off of the AC

adapter unless there is a power outage, in which case the unit

will begin using the batteries.

IMPORTANT: Use only the AC adapters included with your

monitor. Do not use these adapters with any other equipment.

IMPORTANT: Only use the AC adapters included with your monitor. Do not use these adapters with any

other equipment. Movement Sensitivity Control. The movement sensitivity control is on the back of the

Nursery Unit. The level has been preset to 2.5 (see fig. 3). Do not adjust this unless you receive false

alarms. Refer to the Movement Sensitivity Adjustment section on Pg. 11 for more information. It is extremely

important to follow our instructions for setting the sensitivity level.

Now plug the Sensor Pad cord into the jack on the back of the Nursery Unit marked “Sensor Pad.”

Turn the Nursery Unit on using the switch on the left. The green Power Indicator will light up.

CORRECT

Sensor Pad Centered Turquoise Side Up

INCORRECT

Sensor Pad Off Center

INCORRECT

Sensor Pad Turquoise Side Down

POSITION OF SENSOR PAD UNDER MATTRESS (Top Down View of Crib)

Sensor Pad Sensor Pad

CORRECT INCORRECT

PLACEMENT OF SENSOR PAD CORD

Figure 1

fig. 2

SENSOR PAD (See figs. 1 and 2)

Place the Sensor Pad under the center of the crib mattress with the blue side facing up. Do not place any loose bedding

or linen between the crib mattress and the Sensor Pad. The Sensor Pad must rest on a flat, firm surface. If your crib has

a spring or slat base, place a piece of Masonite board under the Sensor Pad. This support must measure at least 13

inches long on all four sides and 1/4 inch thick. (You may order a Masonite board directly from us.

Call Graco at 1-800-345-4109). If your crib has a plywood base, your mattress support is firm enough to use the monitor

properly. Only use your Angelcare® monitor in a stationary sleeping environment such as a crib where the Sensor Pad

can rest on a flat, firm surface. Be sure to place the turquoise side of the Sensor Pad facing up.

CAUTION: To avoid potential strangulation accidents resulting from loose cords or wires in the crib, make sure the

Sensor Pad cord passes underneath the mattress entirely. After positioning the Sensor Pad under the mattress, bring the

cord to the corner of the crib and secure it to the top and bottom of the leg of the crib, or wind it around the leg

(see fig. 1).

Setting Up Your Monitor

fig. 3

fig. 1

Movement Sensitivity Control.

Micro.

Tic / Alarm

Low Batt. / Power

Sound &

Movement

Sound

Only

Tic O

Sensor Pad

Sensitivity

Nursery

Unit

Model #AC201

Activating Units

Sound Only

Always test your monitor before using it the first time and then on a periodic basis.

Before testing your monitor, complete the setup process as described above.

On the back of the Nursery Unit select one of the following three functions:

• Sound & Movement: You will be able to hear your baby's sounds, see sound lights, and hear a “Tic” sound with

every movement your baby makes. If no movement is detected, the “Tic” will stop and after 20 seconds the alarm

will sound.

• Tic Off: In this mode you will not hear a “Tic” with every movement. You will still hear your baby's sounds and

see sound lights, and your baby's movement is still being detected. The default setting is “Tic Off.”

• Sound Only: The Movement Sensor is disabled but you will still be able to hear your baby's sounds and see

sound lights. Your Angelcare® works like a regular sound monitor when set to “Sound Only.”

Turn the Parents' Unit ON by selecting either channel "A" or "B". Make sure

it is set to the same channel as the Nursery Unit. The green power indicator

light will light up. Choose the channel that gives you the best reception.

Select "Sound Only" as shown.

Adjust the volume to the desired level as shown.

Sound &

Movement

Sound

Only

Tic O

Sensor Pad

Sensitivity

Nursery

Unit

Model #AC201

Sound & Movement

• Sound & Movement: You will be able to hear your baby's

sounds, see sound lights, and hear a “Tic” sound with every

movement your baby makes. If no movement is detected, the

“Tic” will stop and after 20 seconds the alarm will sound.

NOTE: Make Sure your Sensor Pad is set up before proceeding with this section. If you haven't set up your

Sensor Pad please go to Pg.8 for instructions on how to properly set up the Sensor Pad.

Switch the Nursery Unit to the "Sound & Movement" function. Turn the Parents' Unit ON by selecting either

channel "A" or "B". Make sure it is set to the same channel as the Nursery Unit. The Movement Indicator Light on

the Nursery Unit will flash red, green, and then emit a single "Tic" sound. Gently pat your hand on the mattress.

The green Movement Indicator Light will continue to flash with every movement. The Nursery Unit will also tick with

every movement.

Remove your hand from the mattress. Due to no movement, the ticking will stop, the Movement Indicator Light will

stop flashing, and a pre-alarm beep will sound after 15 seconds. Five seconds later the alarm will sound and the

red Alarm Indicator Light will flash continuously.

Tic Off

You can also test for movement with the Nursery Unit set to the “Tic Off” position. In this case, you will not hear a

constant ticking when you touch the mattress. When you remove your hand from the mattress the Movement

Indicator Light will stop flashing, a pre-alarm beep will sound after 15 seconds, and five seconds later the alarm will

sound and the red Alarm Indicator Light will flash continuously.

To turn off the alarm, turn the Nursery Unit off or pat your hand lightly on the mattress so the Sensor Pad will

redetect movement. The red Alarm Indicator Light on the Nursery Unit will continue to flash for one minute and it

will then revert to green.

If the alarm does not sound when you are not touching the mattress, the Sensor Pad may be detecting a

continuous vibration from another source from inside and/or outside your baby's room. Common sources of this

interference are crib mobiles, fans, washing machines, or even loud music. Therefore, it is very important to make

sure all vibration sources are eliminated before using the monitor. Place the crib near a solid supporting

wall and away from strong air currents. Do not use crib mobiles or accessories that may cause vibrations. Avoid

contact with the crib when the monitor is in use. If you find the alarm will still not sound when you are not touching

the mattress or crib, the monitor is on, and you have removed all external sources of vibration, the sensitivity level

may need to be decreased. Please refer to the Movement Sensitivity Adjustment section on page 11.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Graco Babyphone Handbücher

Graco

Graco iMonitor 2797 Bedienungsanleitung

Graco

Graco iMonitor 2791 Bedienungsanleitung

Graco

Graco 2M15 Bedienungsanleitung

Graco

Graco 2770 Bedienungsanleitung

Graco

Graco iMonitor Vibe 2M22VIB Bedienungsanleitung

Graco

Graco Flat Panel LCD Video & Sound Monitor Bedienungsanleitung

Graco

Graco imonitor Bedienungsanleitung

Graco

Graco Ultra Clear vibe Bedienungsanleitung

Graco

Graco Ultra Clear 2L01VIB Bedienungsanleitung

Graco

Graco Direct Connect 2M17 Bedienungsanleitung

Graco

Graco SoundSleep Bedienungsanleitung

Graco

Graco UltraClear 2755 Bedienungsanleitung

Graco

Graco 2L00 Simple Sounds Bedienungsanleitung

Graco

Graco Direct Connect 2M17 Bedienungsanleitung

Graco

Graco Ultraclear Bedienungsanleitung

Graco

Graco 2797DIG - iMonitor Digital Color Video Baby... Bedienungsanleitung

Graco

Graco Secure Coverage 2M19VIB Bedienungsanleitung

Graco

Graco Sound Sleep Bedienungsanleitung

Graco

Graco True Focus 2V00 Bedienungsanleitung

Graco

Graco Ultraclear Bedienungsanleitung

Graco

Graco 2L03 Sound Select Bedienungsanleitung

Graco

Graco PD160479 Bedienungsanleitung

Graco

Graco PD191608 Bedienungsanleitung

Graco

Graco Ultra Clear 1750483 Bedienungsanleitung

Beliebte Babyphone Handbücher anderer Marken

Philips

Philips SCD 469 Bedienungsanleitung

Oricom

Oricom Babysense 7 Bedienungsanleitung

Levana

Levana TW502 Bedienungsanleitung

Luvion

Luvion Essential Bedienungsanleitung

Philips

Philips AVENT SCD841 Bedienungsanleitung

NUK

NUK Eco Control Video Display 550VD Bedienungsanleitung

Lorex

Lorex sweet peek mini Bedienungsanleitung

Mondevices

Mondevices MonBaby 2 Bedienungsanleitung

Famidoc

Famidoc FDBB-V2 Bedienungsanleitung

babymoov

babymoov High Care A014001 Bedienungsanleitung

Ramili

Ramili RV1000 Bedienungsanleitung

Philips

Philips SBC SC364 Bedienungsanleitung

Swann

Swann SW231-FLO Bedienungsanleitung

Badabulle

Badabulle Baby Online 300 m+ Bedienungsanleitung

Philips AVENT

Philips AVENT SCD526/00 Bedienungsanleitung

Uniden

Uniden Guardian UBR223 Bedienungsanleitung

Summer

Summer Day & Night 28470A Bedienungsanleitung

Ivation

Ivation Wireless Monitoring System Bedienungsanleitung