Graco 17B190 Bedienungsanleitung

ti24

093a

Instruction

Glass Bead Dispense Kits

For professional application of traffic marking reflective beads. Not approved for use in

European explosive atmosphere locations.

Models

17B190 Kit: Replaces 12” bead box with 16” bead box

26D112 Kit: Replaces 12” bead box with 18” bead box

Follow these instructions when removing a smaller bead box and installing the larger 16-inch (40cm) or 18-inch

(45cm) bead box on the ThermoLazer 300TC and ProMelt. Refer to the ThermoLazer Repair and Operation manuals

as needed for additional information.

Related Manuals

IMPORTANT SAFETY INSTRUCTIONS

Read all warnings and instructions in ThermoLazer Operation manual.

Be familiar with the controls and the proper usage of the equipment.

Save these instructions.

Manual in

English Description

3A1319 ThermoLazer Operation

3A1320 ThermoLazer Repair

334145B

Removal

2 334145B

Removal

Remove Gas Line

Close manual gas shut-off valve on propane tank.

1. Disconnect gas hose at the tee on the frame above

the drive axle. This hose assembly goes to the rear

screed burner manifold.

2. Disconnect gas tube (373) at valve fitting (151).

Discard the hose assembly.

Remove Shroud Door

1. Remove four screws (105) that secure die shroud

door (66) to die shroud. Remove and discard the

door.

ti24109a

ti24110a

ti24134a

373

151

66 105

ti24159a

Removal

334145B 3

2. Remove three screws that hold die support rod to

die shroud.

3. Remove die support rod. Save for reuse.

Remove Bead Box Assembly

1. Loosen bead hose retaining clamps (160) and

remove hose (189) from manifold (69a) and from

bead hopper. Discard the hose assembly.

2. Remove torch holder (204), mounting screw (141),

flatwasher (123), and locknut (97). Save for reuse.

3. Separate bead dispenser link from bead dispenser

box by removing clevis cotter hair pin (268). Save

for reuse.

4. Loosen screws (6) and slide bead dispenser

assembly off the mounting tube.

105

ti24165a

ti24167a

69a

160

189

ti24168a

141 204

123 97

141 204

123 97

268

ti24173a

ti24177a

Installation

4 334145B

Installation

Install Bead Box

1. Loosen screws and slide bead dispenser onto bead

box support tube. Align bead box drive wheel with

center of unit wheel.

2. Secure to the support tube using the bolts in the

two bead box clamps.

3. Install torch holder.

4. Slide hose clamps onto bead hoses.

5. Connect hoses to bead hopper and manifolds. Use

a screw driver to tighten hose clamps.

ti24189a

ti24200a

ti24201a

Installation

334145B 5

6. Connect bead dispenser link to bead dispenser box

by installing clevis cotter hair pin (268) removed

earlier.

7. Use a cable tie to secure outer bead hose to bead

dispenser link.

Install Shroud Door

1. Slide die support rod (34) removed earlier into die

shroud. Secure die support rod to die shroud with

three new screws (105) provided.

2. Position die shroud door (66) on die shroud and

secure with four new screws provided.

ti24203a

ti24204a

ti24185a

105

ti24208a

Installation

6 334145B

Install Screed Burner Gas Line

1. Apply pipe sealant to hose fitting.

2. Connect gas hose at the tee on the frame above

the drive axle.

3. Connect gas tube (373) to fittings at both ends.

Checks and Adjustments

Check gas lines and fittings for gas leaks. Use soap and

water mixture or LP-gas leak detector to detect gas

leaks.

Refer to Operation and Repair manuals for operation

and adjustments.

ti24209a

ti24210a

17B190 Parts

334145B 7

17B190 Parts

Ref. Part Description Qty.

1 17B254 BOX, bead, 16” (40 cm), complete 1

26D108 BOX, bead, 18” (45 cm), complete 1

2 15X765 WHEEL, drive, bead 1

3 100664 SCREW, set, sch 1

4 257399 CLAMP, beadbox 1

5 17B264 BRACKET, pivot, mount, 16” bead 1

26D113 BRACKET, pivot, mount, 18” bead 1

6 100101 SCREW, cap, hex hd 2

7 111195 SCREW, cap, flnghd 1

8 17B915 SCREW, cap, flnghd, 1/2-13 1

18F299 BOLT, socket head, 1/2-13 1

9 119547 NUT, hex, lock, nylon, thin 2

10 17B916 HOSE, bead 2

11 116789 CLAMP, hose 4

12 17B917 DOOR, chamber, die, 16” bead 1

18F263 DOOR, chamber, die, 18” bead 1

13 112798 SCREW, thread forming, hex hd (not

shown)

14 16J469 LABEL, rear burner lighting inst 1

15 16J468 LABEL, torch lighting inst 1

16 16H841 LABEL, instructions, SMARTDIE II 1

17 17B263 MANIFOLD, torch, die, rear, 16” 1

18F292 MANIFOLD, torch, di e, rear, 18” 1

18 555458 FITTING, 1/8M BSPT X 1/8F NPTF 5

19 16T921 FITTING, flow control, assembly 5

20 16W411 HOUSING, burner, GEN II 5

21 16H104 INDICATOR, burner 5

22 104765 PLUG, pipe headless 2

23 16H192 BRACKET, support, manifold, rear, L 1

24 16H107 BRACKET, support, manifold, rear, R 1

25 113958 RING, retaining, external 2

26 101550 SCREW, cap, sch 4

27 159840 ADAPTER 1

28 16Y844 TUBE, formed, gas 1

29 118484 FITTING, connector 2

30 113093 CONNECTOR, pipe 1

31 125064 VALVE, needle, gas, 1/4 NPT 1

32 16Y249 HOSE, gas, die back 1

33 26D622 BRACKET, torch 1

34 802127 SCREW, cap, hex hd 2

35 104541 NUT, lock 2

Ref. Part Description Qty.

All written and visual data contained in this document reflects the latest product information available at the time of publication.

Graco reserves the right to make changes at any time without notice.

Original instructions. This manual contains English. MM

Graco Headquarters: Minneapolis

International Offices: Belgium, China, Japan, Korea

GRACO INC. AND SUBSIDIARIES • P.O. BOX 1441 • MINNEAPOLIS MN 55440-1441 • USA

www.graco.com

Revision B, May 2022

17B254 Parts

225

521

2019

ti24105a

Ref. Part Description Qty.

1 17B256 HOUSING, dispenser, 16” (40 cm) 1

18F257 HOUSING, dispenser, 18” (45 cm) 1

2 SHAFT, knurled (not sold separately) 1

3 16H293 BRACKET, left, bead dispenser 1

4 16H292 BRACKET, right, bead dispenser 1

5 123304 BEARING, sealed 2

6 17B258 GATE, poly, 16” 1

18F256 GATE, poly, 18” 1

7 17B259 GATE, backer bar, 16” 1

18F252 GATE, backer bar, 18” 1

8 110631 SCREW, socket head 8

9 17B260 ADJUSTER, bead dispenser, 16” 1

18F255 ADJUSTER, bead dispenser, 18” 1

10 123481 SCREW, shoulder, 1/4-20 2

11 16U612 PLATE, slide, 1-inch 16

13 112310 SCREW, cap sch 5

15 17B261 MANIFOLD, assembly 2

16 112788 SCREW, cap sch 8

17 121112 SCREW, cap socket head 2

18 16U614 BRACKET, bead box linkage 1

19 295709 SCREW, cap, socket head 1

20 15X282 HANDLE, adjuster 1

21 114797 GASKET 2

22 123261 SCREW, thumb 1

23 104034 WASHER, flat 32

24 114708 SPRING, compression 16

25 119872 SCREW, shoulder 16

Ref. Part Description Qty.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Industrieanlagen Handbücher

Graco

Graco PrecisionFlo XL Bedienungsanleitung

Graco

Graco Therm-O-Flow 5 Bedienungsanleitung

Graco

Graco 25M777 Bedienungsanleitung

Graco

Graco 15H874 Bedienungsanleitung

Graco

Graco SaniForce STU Bedienungsanleitung

Graco

Graco Reactor A Series Bedienungsanleitung

Graco

Graco PR70 Series Bedienungsanleitung

Graco

Graco 918478 Bedienungsanleitung

Graco

Graco 24Y326 Handbuch

Graco

Graco HFRL Bedienungsanleitung

Graco

Graco 234413 Bedienungsanleitung

Graco

Graco ExactaBlend AGP Bedienungsanleitung

Graco

Graco 970086 Bedienungsanleitung

Graco

Graco Therm-O-Flow 200 Stücklistenhandbuch

Graco

Graco XM PFP Stücklistenhandbuch

Graco

Graco ProMix 2KS Bedienungsanleitung

Graco

Graco 950 Series Bedienungsanleitung

Graco

Graco 24A431 Bedienungsanleitung

Graco

Graco Reactor 2 E-30 Gebrauchs- und Pflegehandbuch

Graco

Graco ProMix PD2K Bedienungsanleitung

Graco

Graco Ultra Max II ProContractor Handbuch

Graco

Graco 255703 Stücklistenhandbuch

Graco

Graco 970196 Bedienungsanleitung

Graco

Graco THERM-O-FLOW 234239 Bedienungsanleitung

Beliebte Industrieanlagen Handbücher anderer Marken

ABB

ABB Unifix AD Handbuch

Mark 7

Mark 7 Evolution Bedienungsanleitung

Husky

Husky HyPET Bedienungsanleitung

bora

bora PM-1800 Bedienungsanleitung

Grizzly

Grizzly T32428 Bedienungsanleitung

Siemens

Siemens 8MF1 Series Bedienungsanleitung

ABB

ABB HT610965 Bedienungsanleitung

ABB

ABB SafeLink Bedienungsanleitung

Phoenix

Phoenix PHX-150 Bedienungsanleitung

ABB

ABB A165-L32 Bedienungsanleitung

ABB

ABB HT842936 Bedienungsanleitung

Hermetica

Hermetica 10 Series Bedienungsanleitung

HORNER

HORNER OEE Solution Bedienungsanleitung

Hammerhead

Hammerhead HG375 Bedienungsanleitung

SCHUNK

SCHUNK VERO-S NSE-A3 138 Gebrauchsanweisung

ABB

ABB HT566657 Bedienungsanleitung

Webasto

Webasto GSE CAN Bedienungsanleitung

ABB

ABB HT614003 Bedienungsanleitung