Graco Husky 2150e Bedienungsanleitung

Operation

Husky™ 2150e

Electric-Operated Diaphragm Pump 3A4068E

2–Inch pumps with electric drive for ﬂuid transfer applications.

Not approved for use in explosive atmospheres or hazardous locations unless otherwise stated. See

Approvals page for more information. For professional use only.

Important Safety Instructions

Read all warnings and instructions in this manual and in your Husky

2150e Repair/Parts manual.

Save these instructions.

Maximum Working Pressure: 100 psi

(0.69 MPa, 6.9 bar)

See page 7 for approvals.

PROVEN QUALITY. LEADING TECHNOLOGY.

Contents

Related Manuals ................................................ 2

Warnings ........................................................... 3

onﬁguration Number Matrix............................... 6

Ordering Information........................................... 8

Installation.......................................................... 9

General Information ..................................... 9

Tighten Fasteners........................................ 9

Tips to Reduce avitation............................. 9

Mount the Pump .......................................... 12

Ground The System..................................... 13

Air Line........................................................ 14

Fluid Supply Line ......................................... 14

Fluid Outlet Line........................................... 14

Electrical onnections.................................. 15

Leak Sensor Wiring...................................... 17

ompressor Wiring ...................................... 18

Operation........................................................... 19

Tighten Fasteners........................................ 19

Initial onﬁguration (A with VFD)................ 19

Flush the Pump Before First Use .................. 19

Transfer Mode Vs. Low Pulsation

Mode ............................................. 19

Start and Adjust the Pump............................ 19

Pressure Relief Procedure............................ 20

Pump Shutdown .......................................... 20

VFD Operation ................................................... 21

VFD ontrol Panel....................................... 21

Adjust the Speed ......................................... 21

Maintenance ...................................................... 22

Maintenance Schedule................................. 22

Lubrication................................................... 22

Tighten Threaded onnections..................... 22

Flushing and Storage ................................... 22

Torque Instructions............................................. 23

Torque sequence......................................... 23

Performance harts............................................ 25

Dimensions........................................................ 29

Technical Data ................................................... 38

Graco Standard Husky Pump Warranty................ 44

elated Manuals

Manual Number Title

3A5131 Husky™ 2150e Electric-Operated Diaphragm Pump, Repair/Parts

3A4068E

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The

exclamation point symbol alerts you to a general warning and the hazard symbols refer to procedure-speciﬁc

risks. When these symbols appear in the body of this manual or on warning labels, refer back to these

Warnings. Product-speciﬁc hazard symbols and warnings not covered in this section may appear throughout

the body of this manual where applicable.

WARNING

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can

cause electric shock.

• Turn off and remove power before disconnecting any cables and before servicing or installing

equipment. For cart-mounted models, unplug the power cord. For all other units, disconnect

power at the main switch.

• onnect only to grounded power source.

• All electrical wiring must be done by a qualiﬁed electrician and comply with all local codes

and regulations.

• Wait ﬁve minutes for capacitor discharge before opening equipment.

FIRE A D EXPLOSIO HAZARD

Flammable fumes, such as solvent and paint fumes, in

work area

canigniteorexplode.Paint

or solvent ﬂowing through the equipment can cause static sparking. To help prevent ﬁre and

explosion:

• Use equipment only in well ventilated area.

• Eliminate all ignition sources; such as pilot lights, cigarettes, portable electric lamps, and

plastic drop cloths (potential static arc).

• Ground all equipment in the work area. See

Grounding

instructions.

• Keep work area free of debris, including solvent, rags and gasoline.

• Do not plug or unplug power cords, or turn power or light switches on or off when ﬂammable

fumes are present.

• Use only grounded hoses.

•

Stop operation immediately

if static sparking occurs or you feel a shock

Do not use

equipment until you identify and correct the problem.

• Keep a working ﬁre extinguisher in the work area.

Static charge may build up on plastic parts during cleaning and could discharge and ignite

ﬂammable vapors. To help prevent ﬁre and explosion:

• lean plastic parts only in well ventilated area.

• Donotcleanwithadrycloth.

• Do not operate electrostatic guns in equipment work area.

3A4068E 3

Warnings

WARNING

PRESSURIZED EQUIPME T HAZARD

Fluid from the equipment, leaks, or ruptured components can splash in the eyes or on skin

and cause serious injury.

• Follow the

Pressure Relief Procedure

when you stop spraying/dispensing and before

cleaning, checking, or servicing equipment.

• Tighten all ﬂuid connections before operating the equipment.

• heck hoses, tubes, and couplings daily. Replace worn or damaged parts immediately.

EQUIPME T MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the inﬂuence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated

system component. See

Technical Data

in all equipment manuals.

• Use ﬂuids and solvents that are compatible with equipment wetted parts. See

Technical Data

in all equipment manuals. Read ﬂuid and solvent manufacturer’s warnings. For complete

information about your material, request Safety Data Sheet (SDS) from distributor or retailer.

• Turn off all equipment and follow the

Pressure Relief Procedure

when equipment is not in use.

• heck equipment daily. Repair or replace worn or damaged parts immediately with genuine

manufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modiﬁcations may void agency approvals

and create safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. all your distributor for information.

• Route hoses and cables away from trafﬁc areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• omply with all applicable safety regulations.

PRESSURIZED ALUMI UM PARTS HAZARD

Use of ﬂuids that are incompatible with aluminum in pressurized equipment can cause serious

chemical reaction and equipment rupture. Failure to follow this warning can result in death,

serious injury, or property damage.

• Do not use 1,1,1-trichloroethane, methylene chloride, other halogenated hydrocarbon

solvents or ﬂuids containing such solvents.

• Do not use chlorine bleach.

• Many other ﬂuids may contain chemicals that can react with aluminum. ontact your material

supplier for compatibility.

43A4068E

Warnings

WARNING

THERMAL EXPA SIO HAZARD

Fluidssubjectedtoheatinconﬁnedspaces,includinghoses,cancreatearapidriseinpressure

due to the thermal expansion. Over-pressurization can result in equipment rupture and serious

injury.

• Openavalvetorelievetheﬂuidexpansionduringheating.

• Replace hoses proactively at regular intervals based on your operating conditions.

PLASTIC PARTS CLEA I G SOLVE T HAZARD

Many solvents can degrade plastic parts and cause them to fail, which could cause serious

injury or property damage.

• Use only compatible water-based solvents to clean plastic structural or pressure-containing

parts.

•See

Technical Data

in this and all other equipment instruction manuals. Read ﬂuid and

solvent manufacturer’s Safety Data Sheet (SDS) and recommendations.

TOXIC FLUID OR FUMES HAZARD

Toxic ﬂuids or fumes can cause serious injury or death if splashed in the eyes or on skin,

inhaled, or swallowed.

• Read Safety Data Sheet (SDS) to know the speciﬁc hazards of the ﬂuids you are using.

• Store hazardous ﬂuid in approved containers, and dispose of it according to applicable

guidelines.

BUR HAZARD

Equipment surfaces and ﬂuid that’s heated can become very hot during operation. To avoid

severe burns:

• Do not touch hot ﬂuid or equipment.

PERSO AL PROTECTIVE EQUIPME T

Wear appropriate protective equipment when in the work area to help prevent serious injury,

including eye injury, hearing loss, inhalation of toxic fumes, and burns. This protective

equipment includes but is not limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the ﬂuid and solvent

manufacturer.

3A4068E 5

Conﬁguration Number Matrix

heck the identiﬁcation plate (ID) for the

onﬁguration Number of your pump. Use the

following matrix to deﬁne the components of your

pump.

Sample Conﬁguration umber:

2150A-E,A04AA1TPTPTP- -

2150 AEA04 AA1 TP TP TP --

Pump

Model Wetted

Section

Material

Drive Center

Section

Material

Gear Box

and Com-

pressor

Motor Fluid Covers and

Manifolds Seats Balls Diaphragms Manifold

O-Rings

OTE:

Some combinations are not possible. Please refer to Ordering Information, page 8 .

Pump Wetted Section

Material Drive TypeCenter Section

Material Gearbox and

Compressor Motor

2150 A

Aluminum

Electric

Aluminum

No Gearbox or

ompressor

Standard

Induction Motor

onductive

Polypropylene

Stainless Steel

High Speed Gear

Ratio

ATEX Induction

Motor

PVDF

High Speed

Gear Ratio/120V

ompressor

Flameproof

Induction Motor

ast Iron

High Speed

Gear Ratio/240V

ompressor

No Motor

Polypropylene

Mid Speed Gear

Ratio

Stainless Steel

Mid Speed

Gear Ratio/120V

ompressor

Mid Speed

Gear Ratio/240V

ompressor

Low Speed Gear

Ratio

Low Speed

Gear Ratio/120V

ompressor

Low Speed

Gear Ratio/240V

ompressor

63A4068E

Conﬁguration Number Matrix

Fluid Covers and

Manifolds Seat Material Ball Material Diaphragm Material Manifold

O-Rings

Aluminum, npt

Geolast

Acetal

Geolast

––

Model does

not use o-rings

Aluminum, bsp

Polypropy-

lene

Polychloroprene

Weighted

PTFE/EPDM

2–Piece

PTFE

onductive

polypropylene,

end ﬂange

PVDF

Geolast

Santoprene

PVDF, end

ﬂange

Santoprene

PTFE

TPE

Polypropylene,

end ﬂange

316 Stainless

Steel

440 Stainless

Steel

Stainless steel,

npt

TPE

Santoprene

Stainless steel,

bsp

TPE

S5-1

Stainless steel,

center ﬂange,

horizontal outlet

S5-2

Stainless steel,

center ﬂange,

vertical outlet

ast Iron,

standard ports,

npt

ast Iron,

standard ports,

bsp

Approvals

✦ Aluminum, cast iron, conductive

polypropylene, and stainless steel pumps with

motor code are certiﬁed to: II 2 G Ex h d IIB T3 Gb

✚ Aluminum, cast iron, conductive

polypropylene, and stainless steel pumps with

motor code Garecertiﬁedto: II2GExhIIBT3Gb

★ Motors coded Darecertiﬁedto: lass I, Div 1, Group D, T3B

lass II, Div 1, Group F & G, T3B

All Models (except gearbox and compressor

codes 05, 15, and 25, or motor code D)are

certiﬁed to:

3A4068E 7

Ordering Information

To Find Your Nearest Distributor

1. Visit www.graco.com.

2. lick on

Where to Buy

and use the

Distributor Locator.

To Specify the Conﬁguration of a New Pump

Please call your distributor.

Use the

Online Diaphragm Pump Selector Tool at www.graco.com.

Go to the

Process Equipment Page.

To Order Rep acement Parts

Please call your distributor.

83A4068E

Installation

Installation of this equipment involves potentially

hazardous procedures. Only trained and qualiﬁed

personnel who have read and who understand

the information in this manual should install this

equipment.

• All electrical wiring must be done by a qualiﬁed

electrician and comply with all local codes and

regulations

Genera Information

The Typical Installation shown is only a guide for

selecting and installing system components. ontact

your Graco distributor for assistance in planning a

system to suit your needs. Always use Genuine

Graco Parts and accessories. Be sure all accessories

are adequately sized and pressure rated to meet the

system’s requirements.

Reference letters in the text, for example (A), refer to

the callouts in the ﬁgures.

Tighten Fasteners

Before mounting and using the pump for the ﬁrst time,

check and retorque all external fasteners. Follow

Torque Instructions, page 23, or see the torque

tag on your pump. After the ﬁrst day of operation,

retorque the fasteners.

Tips to Reduce Cavitation

avitation in a double diaphragm pump is the

formation and collapse of bubbles in the pumped

liquid. Frequent or excessive cavitation can cause

serious damage, including pitting and early wear of

ﬂuid chambers, balls, and seats. It may result in

reduced efﬁciency of the pump. avitation damage

and reduced efﬁciency both result in increased

operating costs.

avitation depends on the vapor pressure of the

pumped liquid, the system suction pressure, and the

velocity pressure. It can be reduced by changing any

of these factors.

1. Reduce vapor pressure: Decrease the

temperature of the pumped liquid.

2. Increase suction pressure:

a. Lower the installed position of the pump

relative to the liquid level in the supply.

b. Reduce the friction length of the suction

piping. Remember that ﬁttings add friction

length to the piping. Reduce the number of

ﬁttings to reduce the friction length.

c. Increase the size of the suction piping.

OTE:

Be sure the inlet ﬂuid pressure does not

exceed 25% of the outlet working pressure.

3. Reduce liquid velocity: Slow the cyclic rate of

the pump.

Pumped liquid viscosity is also very important but

normally is controlled by factors that are process

dependent and cannot be changed to reduce

cavitation. Viscous liquids are more difﬁcult to pump

and more prone to cavitation.

Graco recommends taking all the above factors

into account in system design. To maintain pump

efﬁciency, supply only enough power to the pump to

achieve the required ﬂow.

Graco distributors can supply site speciﬁc

suggestions to improve pump performance and

reduce operating costs.

3A4068E 9

Installation

Figure 1 Typical Installation for pumps without a

compressor

System Components Accessories/Components ot Supplied

B Fluid inlet port A* Power cord to VFD

Fluid outlet port F* Grounded, ﬂexible air supply line

DMounting feet G Bleed-type master air valve

E Air inlet port H Air ﬁlter/regulator assembly

PPump Ground JMaster air valve (for accessories)

Renter section regulator K* Grounded, ﬂexible ﬂuid supply line

LFluiddrainvalve(mayberequiredforyour

pump installation)

MFluid shutoff valve

N* Grounded, ﬂexible ﬂuid outlet line

* Required. Supplied by customer.

10 3A4068E

Andere Handbücher für Husky 2150e

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco 232437 Bedienungsanleitung

Graco

Graco Husky 715 Bedienungsanleitung

Graco

Graco GH 130 Betriebsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

Graco

Graco LubePro A4000 Bedienungsanleitung

Graco

Graco King B Series Bedienungsanleitung

Graco

Graco ChemSafe 307 Bedienungsanleitung

Graco

Graco Dyna-Star 200:1 Bedienungsanleitung

Graco

Graco President 232204 Bedienungsanleitung

Graco

Graco Python XL-DA25 Series Stücklistenhandbuch

Graco

Graco PRESIDENT HYDRA-CAT 231657 Bedienungsanleitung

Graco

Graco Dura-Flo XL 1000cc Leitfaden

Graco

Graco G-Mini 25R800 Bedienungsanleitung

Graco

Graco 205394 Bedienungsanleitung

Graco

Graco RoadLazer A Series Bedienungsanleitung

Graco

Graco ChemSafe 1590 Stücklistenhandbuch

Graco

Graco ChemSafe 205 Stücklistenhandbuch

Graco

Graco Dyna-Star 236753 Datenblatt

Graco

Graco G3 Pro Bedienungsanleitung

Graco

Graco President B Series Datenblatt

Graco

Graco VPM Series Bedienungsanleitung

Graco

Graco Check-Mate 2100 A Series Bedienungsanleitung

Graco

Graco Hydra-Clean 1040 Bedienungsanleitung

Graco

Graco C Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung