Graco LubePro A4000 Bedienungsanleitung

Instructions

Grease or Oil A4000

Reciprocating

LubePro™ Pump 3A5266G

For pumping non-corrosive and non-abrasive lubricants only. For professional use only.

Models: Page 2

4000 psi (27.58 MPa, 275.8 bar) Maximum Working

Pressure

Related Manuals

406900 - Air Motor Repair Kit

Important Safety Instructions

Read all warnings and instructions in

this manual. Save these instructions.

Contents

2 3A5266G

Contents

Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Typical Installation: Injector System . . . . . . . . . . 5

Typical Installation: Divider Valve System . . . . . . 6

Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Low Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Air and Fluid Line Accessories . . . . . . . . . . . . . . 8

Electric Vent Valve Kit . . . . . . . . . . . . . . . . . . . . . 8

Fill Reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Priming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Set System Pressure . . . . . . . . . . . . . . . . . . . . . 11

Pressure Relief Procedure . . . . . . . . . . . . . . . . 11

Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Pump . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Shut Down . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Remove Air Motor . . . . . . . . . . . . . . . . . . . . . . . 14

Pump Lower Disassembly . . . . . . . . . . . . . . . . 14

Pump Lower Reassembly . . . . . . . . . . . . . . . . . 16

Parts: Grease Models . . . . . . . . . . . . . . . . . . . . . . 18

Parts: Grease Models . . . . . . . . . . . . . . . . . . . . . . 19

Parts: Oil Models . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Parts: Oil Models . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Repair Air Valve . . . . . . . . . . . . . . . . . . . . . . . . . 22

Replace Pilot Valves . . . . . . . . . . . . . . . . . . . . . 24

Repair Air Motor . . . . . . . . . . . . . . . . . . . . . . . . 24

Air Motor Installation . . . . . . . . . . . . . . . . . . . . . 27

Air Motor Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Air Motor Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Complete Air Valve Replacement Kit . . . . . . . . 30

Air Valve Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Pump Kits Parts . . . . . . . . . . . . . . . . . . . . . . . . 32

Additional Pump Kits . . . . . . . . . . . . . . . . . . . . . 32

Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Grease Pump Dimensions and Mounting . . . . . . 34

Oil Pump Dimensions and Mounting . . . . . . . . . . 35

Performance Curve . . . . . . . . . . . . . . . . . . . . . . . . 36

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Graco Standard Warranty . . . . . . . . . . . . . . . . . . . 38

Models

Pneumatic

Vent Valve

Series

Progressive

Electric Vent

Valve

Low Level

Detection Fluid

Reservoir

Size Ratio

Pressure

PSI Bar

17U217 - - • Grease 12 lbs (6 L)

40:1 4000 275.8

17P750 17T176 17T193 6 lbs (3 L)

17P751 17T177 17T194 •

17P752 17T178 17T195 Oil 12 pints

(5.5 L)

17P753 17T179 17T196 •

Warnings

3A5266G 3

Warnings

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbols refer to procedure-specific risks. When

these symbols appear in the body of this manual or on warning labels, refer back to these Warnings. Product-spe-

cific hazard symbols and warnings not covered in this section may appear throughout the body of this manual

where applicable.

WARNING

SKIN INJECTION HAZARD

High-pressure fluid from dispensing device, hose leaks, or ruptured components will pierce skin. This

may look like just a cut, but it is a serious injury that can result in amputation. Get immediate surgical

treatment.

• Do not point dispensing device at anyone or at any part of the body.

• Do not put your hand over the fluid outlet.

• Do not stop or deflect leaks with your hand, body, glove, or rag.

• Follow the Pressure Relief Procedure when you stop dispensing and before cleaning, checking,

or servicing equipment.

• Tighten all fluid connections before operating the equipment.

• Check hoses and couplings daily. Replace worn or damaged parts immediately.

PRESSURIZED EQUIPMENT HAZARD

Over-pressurization can result in equipment rupture and serious injury.

• Do not exceed the maximum air input pressure.

• Fill slowly to avoid over pressurizing reservoir.

• Use tubing, hoses and other components with pressure ratings equal to or higher than the pump

rating.

PLASTIC PARTS CLEANING SOLVENT HAZARD

Many cleaning solvents can degrade plastic parts and cause them to fail, which could cause serious

injury or property damage.

• Use only compatible solvents to clean plastic structural or pressure-containing parts.

• See Technical Specifications in all equipment manuals for materials of construction. Consult the

solvent manufacturer for information and recommendations about compatibility.

Warnings

4 3A5266G

ELECTRIC SHOCK HAZARD

This equipment must be grounded. Improper grounding, setup, or usage of the system can cause

electric shock.

• Turn off and disconnect power at main switch before disconnecting any cables and before

servicing or installing equipment.

• Connect only to grounded power source.

• All electrical wiring must be done by a qualified electrician and comply with all local codes and

regulations.

EQUIPMENT MISUSE HAZARD

Misuse can cause death or serious injury.

• Do not operate the unit when fatigued or under the influence of drugs or alcohol.

• Do not exceed the maximum working pressure or temperature rating of the lowest rated system

component. See Technical Specifications in all equipment manuals.

• Use fluids and solvents that are compatible with equipment wetted parts. See Technical Specifi-

cations in all equipment manuals. Read fluid and solvent manufacturer’s warnings. For complete

information about your material, request Safety Data Sheets (SDSs) from distributor or retailer.

• Turn off all equipment and follow the Pressure Relief Procedure when equipment is not in use.

• Check equipment daily. Repair or replace worn or damaged parts immediately with genuine man-

ufacturer’s replacement parts only.

• Do not alter or modify equipment. Alterations or modifications may void agency approvals and cre-

ate safety hazards.

• Make sure all equipment is rated and approved for the environment in which you are using it.

• Use equipment only for its intended purpose. Call your distributor for information.

• Route hoses and cables away from traffic areas, sharp edges, moving parts, and hot surfaces.

• Do not kink or over bend hoses or use hoses to pull equipment.

• Keep children and animals away from work area.

• Comply with all applicable safety regulations.

PERSONAL PROTECTIVE EQUIPMENT

Wear appropriate protective equipment when in the work area to help prevent serious injury, including

eye injury, hearing loss, inhalation of toxic fumes, and burns. Protective equipment includes but is not

limited to:

• Protective eyewear, and hearing protection.

• Respirators, protective clothing, and gloves as recommended by the fluid and solvent manufac-

turer.

CALIFORNIA PROPOSITION 65

This product contains a chemical known to the State of California to cause cancer, birth defects or

other reproductive harm. Wash hands after handling.

WARNING

Installation

3A5266G 5

Installation

Typical Installation: Injector System

(grease model pump shown)

Key:

A Main Air Supply

A1 Switched Air Supply

A2 Vent Valve Air Supply

B Filter/Regulator/Lubricator Assembly

B1 - Air Filter

B2 - Air Regulator

B3 - Air Lubricator

C Air solenoid valve (3-way)

D Pump Module

E Pump Outlet

F Bleed-type Master Air Valve (required)

G High Pressure Lubricant Supply Lines

H Injector

J Lubricator Controller

K Pump Reservoir

L Ground

M Vent Valve

N Low Level Switch (not installed on all pump models)

P Tee-fitting to Vent Valve

R Pump Air Inlet

S Pressure Switch

T Air Motor

FIG. 1: Typical Installation

Power to

Controller

Installation

6 3A5266G

Typical Installation: Divider Valve System

(oil model pump shown)

Key:

A Main Air Supply

A1 Switch Air Supply Line

B Filter/Regulator/Lubricator Assembly

B1 - Air Filter

B2 - Air Regulator

B3 - Air Lubricator

C Air Solenoid Valve (3-way)

D Pump Module

E Pump Outlet

F Bleed-type Master Air Valve (required)

G High Pressure Lubricant Supply Lines

J Lubricator Controller

K Pump Reservoir

L Ground

R Pump Air Inlet

T Air Motor

U Cycle Switch

V Divider Valve

FIG. 2: Typical Installation

Power to

Controller

Installation

3A5266G 7

Grounding

Secure ground wire to grounding screw (66) as shown

in FIG. 3.

Mounting

Install the pump in a location that will adequately sup-

port the weight of the pump when filled with lubricant

and also provides easy operator access to the pump air

controls. See Technical Data, page 35 for pump weight

information and the Dimensions and Mounting layout,

page 28.

1. Secure wall bracket (39) to mounting location. (User

must provide mounting hardware.)

2. Install pump bracket (38) to wall bracket (39).

Secure pump bracket to wall bracket using wash-

ers (60) and nuts (44).

Low Level

For models equipped with a low level switch, connec-

tion is made to pins 1 and 2 for normally closed opera-

tion or pins 1 and 3 for normally open operation. See

FIG. 4.

Grounding is required if a low level switch and/or

an air valve using voltages above 30 VAC or 42

VDC are attached to the pump. Improper ground-

ing can cause electric shock. Grounding reduces

the risk of electric shock by providing an escape

wire for the electric current in the event of malfunc-

tion or breakdown.

FIG. 3

Mount the pump securely so that it cannot move

around during operation. Failure to do so could result

in injury or equipment damage.

FIG. 4

Installation

8 3A5266G

Air and Fluid Line Accessories

Refer to FIG. 1 and FIG. 2, pages 5 and 6, for the follow-

ing instructions.

Install the air line accessories in the order shown in FIG.

1 and FIG. 2, pages 5 and 6.

1. Install an air line filter (B1) to remove harmful dirt

and contaminants from the compressed air supply

2. Install the air regulator (B2) to control pressure.

3. Install an air line lubricator (B3) to lubricate the air

cylinder.

4. Install a bleed-type master air valve (F) to relieve air

trapped between it and the pump. Install the valve

in a location that is easily accessible and located

downstream of the air regulator.

5. Install the(3-way) air solenoid valve (C) for control of

the pump strokes.

6. Connect the vent valve (M).

-Pneumatic Vent Valve

Connect the air powered vent valve to the

pump supply air (A1).

a. Install a t-fitting (P) at the pump inlet.

b. Install a hose between the t-fitting and vent

valve.

-Electric Vent Valve

Connect to pump air control valve power.

a. Install a DIN connector into the vent valve.

b. Connect the leads to the controller output

that signals the pump to turn on.

7. To use the air regulator reading to determine the

fluid output pressure, multiply the ratio of the pump

(40:1) by the air pressure shown on the regulator

gauge; i.e., 40 psi x 40 = 1600 psi (2.75 bar x 40 =

110 bar; 0.27 MPa, x 40 = 10.8 MPa).

8. Limit the air pressure to the pump so that no air line

or fluid line component or accessory is over pres-

surized.

Electric Vent Valve Kit 129713

Grease Models 17T193 and 17T194; Oil

Models 17T195 and 17T196

1. Stop pump. Relieve pressure. See Pressure Relief

Procedure, page 11.

2. Disconnect air line from pump.

3. Remove plug (57) from pump base (2) (FIG. 5).

4. Install valve cartridge (68) in pump base (FIG. 5).

Torque coil nut (a) to 4 to 5 ft-lbs (5.42 to 6.78

N•m). Torque cartridge nut (b) to 16 to 20 ft-lbs

(21.69 to 27.12 N•m).

Trapped air can cause the pump to cycle unexpect-

edly, which could result in serious injury from splash-

ing or moving parts. An air shut off valve (bleed-type

master air valve) is required for the system to protect

you from injury when you are adjusting or repairing

the pump. The air bleed device relieves air trapped

between it and pump after the air supply is shut off.

The maximum working pressure of each component

in the system may not be the same. To reduce the

risk of over-pressurizing any part of the system,

know the maximum working pressure rating of each

component and its connected components. Never

exceed the maximum working pressure of the lowest

rated components connected to a particular pump.

FIG. 5

57 68

Installation

3A5266G 9

Fill Reservoir

Oil Models

1. Open oil fill cap (32) on the top of the reservoir.

NOTE: A filter (33) is installed at the oil fill cap (32) to

prevent lubricant contamination (FIG. 6).

a. Inspect filter (33) before filling reservoir.

b. When needed, remove filter (33) and clean it

thoroughly.

c. If removed in Step b, install filter (33) prior to

adding lubricant.

2. Slowly add oil (ol) until reservoir is filled to capacity

(FIG. 7). Take care to not fill reservoir too quickly

and overflow the reservoir capacity.

3. Close oil fill cap (32) to prevent contamination and

spillage (FIG. 7).

Grease Models

1. Remove dust cap (42) (FIG. 8) from fill stud (26).

2. Connect the quick connect fitting on the fill pump

to the fill stud (26) on the reservoir.

FIG. 6

FIG. 7

FIG. 8

Installation

10 3A5266G

3. Slowly dispense grease from the fill pump into the

reservoir until the grease in the reservoir lifts the fol-

lower plate (45) above the reservoir vent hole (vh)

and air is expended from under the follower plate

(FIG. 9). A small amount of grease may come out of

the vent hole at this time.

Care must be taken not to overfill the reservoir. An

over filled reservoir will vent the excess grease out

of the vent hole (vh) until enough grease is expelled

for the follower plate (45) to block the vent hole.

Overfilling the reservoir could also cause the reser-

voir to rupture due to over-pressurization.

NOTE: The vent hole (vh) is located toward the back

right side of the reservoir and cannot be seen in FIG. 9.

The approximate location of the vent hole is identified

as vh in the illustration.

4. Disconnect the fill pump from the fill stud (26, FIG.

8).

5. Secure dust cap (42) over fill stud (26) (FIG. 8).

Priming

Refer to FIG. 1 and FIG. 2, pages 5 and 6, for the follow-

ing instructions.

NOTE:

• Prime the pump before connecting the outlet to

supply line (G).

• Before priming the pump, the reservoir must be

filled with lubricant (see Fill Reservoir instructions,

page 8).

Run the pump until lubricant, free of air, comes out of

the pump outlet (E). It may take up to 20 pump strokes

to expel the air from the pump and deliver a continuous

flow of lubricant. This will depend on the viscosity of the

lubricant and temperature.

Supply Lines

1. Run the pump until the oil (ol), free of air, comes out

of the pump outlet (E). Connect the supply line (G)

to the pump outlet (E).

2. If there are multiple pumps on the air line, close the

air regulators and bleed-type master air valves to all

but one of the pumps. If there is only one pump,

open its air regulator and bleed-type master air

valve.

3. Open the master air valve from the compressor.

4. Set the air pressure to each pump at the lowest

pressure needed to get the desired results.

Feeder Lines

Fill each feeder line with lubricant prior to connecting

feeder lines to the injector outlet or divider valve.

Injectors

1. Check each injector for proper operation. The injec-

tor stem should move when lubricant is discharged.

2. Adjust the injector output if needed to ensure that

the output volume discharged is sufficient.

Over-pressurization can result in equipment rupture

and serious injury. Fill slowly to avoid over pressuriz-

ing reservoir.

FIG. 9

(vh) (gr)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Graco Wasserpumpe Handbücher

Graco

Graco Mongoose Series Stücklistenhandbuch

Graco

Graco Series A Stücklistenhandbuch

Graco

Graco EGP 25T817 Bedienungsanleitung

Graco

Graco TRITON 1030HP Bedienungsanleitung

Graco

Graco Viscount I 3000 Bedienungsanleitung

Graco

Graco Husky 2150 Bedienungsanleitung

Graco

Graco Mini Fire-Ball 246775 Bedienungsanleitung

Graco

Graco 244195 Betriebsanleitung

Graco

Graco 06529 Bedienungsanleitung

Graco

Graco Series A Stücklistenhandbuch

Graco

Graco Xtreme 116MCN Bedienungsanleitung

Graco

Graco 25C837 Stücklistenhandbuch

Graco

Graco SoloTech i6 Gebrauchs- und Pflegehandbuch

Graco

Graco 198466 Bedienungsanleitung

Graco

Graco GH 733 HYDRA-SPRAY Bedienungsanleitung

Graco

Graco Series A Bedienungsanleitung

Graco

Graco 24R968 Bedienungsanleitung

Graco

Graco G3-G-24NC-8LTA00-0D00L000 Bedienungsanleitung

Graco

Graco Hydra-Clean 1040 Gebrauchs- und Pflegehandbuch

Graco

Graco 247888 Bedienungsanleitung

Graco

Graco Husky 2200 Gebrauchs- und Pflegehandbuch

Graco

Graco SaniForce STU Series Bedienungsanleitung

Graco

Graco Husky Sanitary Series Bedienungsanleitung

Graco

Graco Therm-O-Flow Plus HM55-D Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung