Grandview GRIP084V Bedienungsanleitung

IP SMART SCREEN

USER MANUAL

* Note: Warranty does not cover un-installing

or re-installing unit.

Product Code:

GRIP084/100/120/140/150/180V

GRIP092/102/120/130/140/150/160180/200H

GRIP094/103/110/120/130/140/150/160/180/200C

ambertech.com.au

Protecting your Screen:

To ensure long lasting viewing enjoyment keep

the screen rolled up when not in use. Check both

the front and back surfaces before retracting

into the case to make sure it is free of dust, dirt,

insects or other foreign matter. Use a soft brush

or cloth to lightly remove any foreign particles.

Cleaning your Screen:

Use warm water with a mild detergent to remove

any marks on the surface (only dab, do not rub)

or screen casing. Immediately dry the screen with

a soft cloth or towel. Do not leave it to air dry.

Never use any solvents, chemicals or abrasive

cleaners on the screen surface as they can

permanently damage the screen surface.

RS-232 Control Protocol

Baud Rate: 2400

Data Bits: 8

Stop Bits: 1

Parity: None

Codes below are hexadecimal. No Carriage return is required.

Important: In some cases you may need to enable the RS-232

control by sending hex command: FF EE EE EE AA

(This will only need to be sent once during commissioning,

the setting will remain through subsequent power cycles)

Screen Up: FF EE EE EE DD

Screen Stop: FF EE EE EE CC

Screen Down: FF EE EE EE EE

Excessive Motor Use

The motor will switch off if the screen is used continuously

for more than three minutes. Allow the motor to cool for

30 minutes before using again.

If you do not expect to use your screen for some time,

please disconnect the power.

1800 251 367

or[email protected]

Imported and distributed in Australia by

To the owner

Congratulations on purchasing a Grandview IP

Smart Screen. This screen is designed to produce

the sharpest, most pleasing pictures with

maximum convenience.

Before you start

• Use the correct tools: a level, a measuring tape and a

pencil to mark with.

• Measure the bracket position accurately before

attaching to the wall or ceiling.

• Do not mount the brackets the full width of the casing,

allow at least 100mm at each end for horizontal picture

alignment.

Wall mount

Mount the brackets ﬁrmly eg: into wall studs or bricks.

Ensure the brackets are in level.

Limit settings

The screen is ﬁtted with 2 limits. The limits automatically

stop the screen in the fully UP (top limit) and fully Down

(bottom limit) positions. You can adjust the bottom limit

to set your viewing height.

You may also search for Grandview Limit Setting in

YouTube to view the limit setting technique.

Setting the top limit

Adjusting the top limit may damage your screen and void

your warranty. For this reason the top limit screw is covered

by a warning sticker.

Do not adjust the top limits under any circumstance.

Setting the bottom limit

Caution: Setting the bottom limit beyond the black

leader may render your screen inoperable and void

your warranty.

The bottom limit switch is accessible through a

grommeted hole on the left side of the casing.

Lower the screen to the operating position then insert

the supplied Hex key into the white coloured screw.

Turn it clockwise to raise the screen or turn it anti-

clockwise to lower the screen.

When lowering the bottom limit the screen will move

as you adjust it.

When raising the bottom limit please lift and lower the

screen with the remote or side buttons to see the new

limit setting.

Using close contact WIRING MAP

Locking scre

wLocking piece

Slide the screen onto the brackets and snap into the

groove and tighten the screw.

Up groove

Down

groove

Ceiling installation

Attach the ceiling brackets as shown. Slide the screen and lock

Using 12V Trigger:

Connect the projector and screen with the jack plug cable

provided. Turn “ON” the projector and choose 12V from the

menu, the screen will lower. When the projector is turned

“OFF” the screen will retract into the casing.

Alternatively you may also use the external IR receiver cable

and sensor.

Plug the IR receiver cable into the IR socket on the casing and

mount the sensor in line of sight with the remote.

Now use the remote to lower and retract the screen.

Ensure the wall bracket is

secured to the casing of the

screen before hanging.

Caution:

Before operating the screen you must remove the adhesive

tape which holds the dropper bar to the screen case.

Electrical installation

Grandview IP Smart Screens come with an Australian

standard plug. Simply plug in and your screen is

ready to use.

Operating Instructions

Using IR Remote

Your remote control comes with a battery installed.

To operate your remote:

Press  to lift the screen

Press  to stop the screen

Press  to lower the screen

The Micro switch is used for retracting

or lowering screen in small increments.

Dieses Handbuch passt für folgende Modelle

Andere Grandview Projektionsfläche Handbücher

Grandview

Grandview CB-Pxx Bedienungsanleitung

Grandview

Grandview Fast Fold Bedienungsanleitung

Grandview

Grandview Edge R3 PE-L Series Bedienungsanleitung

Grandview

Grandview Ultimate PP-G Series Bedienungsanleitung

Grandview

Grandview Liberty Flash Series Bedienungsanleitung

Grandview

Grandview FC-FHP-MF Series Bedienungsanleitung

Grandview

Grandview CN Series Bedienungsanleitung

Grandview

Grandview FC-FHMF Series Bedienungsanleitung

Grandview

Grandview CB-MIRC Bedienungsanleitung

Grandview

Grandview GVFA100V Bedienungsanleitung

Grandview

Grandview DIAS DI-M Series Bedienungsanleitung

Grandview

Grandview PT-L Series Bedienungsanleitung

Grandview

Grandview Sky-Show Bedienungsanleitung

Grandview

Grandview Cyber Series CB-MIxx Bedienungsanleitung

Grandview

Grandview Fantasy Series FA-Mxx Bedienungsanleitung

Grandview

Grandview Large Stage MBII Bedienungsanleitung

Grandview

Grandview PE-Y (R7)15 Series Bedienungsanleitung

Grandview

Grandview LF-PU Series Bedienungsanleitung

Grandview

Grandview LEGACY Series Bedienungsanleitung

Grandview

Grandview Motorised Rising Screen Bedienungsanleitung

Grandview

Grandview Edge R7 Bedienungsanleitung

Grandview

Grandview Smart Screen Bedienungsanleitung

Grandview

Grandview Fantasy FC-FHMI Series Bedienungsanleitung

Grandview

Grandview Tripod Bedienungsanleitung

Beliebte Projektionsfläche Handbücher anderer Marken

FART PRODUKT

FART PRODUKT Standard SCREEN Bedienungsanleitung

Draper

Draper E Series Handbuch

Elite Screens

Elite Screens Elite Tripod Series Bedienungsanleitung

Laarhoven

Laarhoven Companion II Bedienungsanleitung

Renogy

Renogy RMS-LFPS-US Bedienungsanleitung

Da-Lite

Da-Lite ExecutiveElectrol Bedienungsanleitung

Samsung

Samsung S*H65* Bedienungsanleitung

FONESTAR

FONESTAR PPTR-43100-FA Bedienungsanleitung

Slide Clear

Slide Clear Varro XL Bedienungsanleitung

Elite Screens

Elite Screens M85XWS1-SRM Bedienungsanleitung

OS РХ-090Н Bedienungsanleitung

Niko

Niko 10-845 Bedienungsanleitung

Speaka Professional

Speaka Professional 2357532 Betriebsanleitung

Sima

Sima XL-72 Bedienungsanleitung

Jasic

Jasic EVO 2.0 ET-200P Bedienungsanleitung

Elite Screens

Elite Screens Starling 2 Series Bedienungsanleitung

InFocus

InFocus SC-WALL GRY-92H Handbuch

Barco

Barco OverView MVL-615 Bedienungsanleitung