GRAUPNER GR-16 HoTT Bedienungsanleitung

No. 33508

2.4 GHz 8 channel receiver

GR-16 HoTT

Manual

2 / 16 33508_sh_V1

3 / 16

33508_sh_V1

Index

Introduction .............................................................................. 4

Service centre............................................................................ 4

Intended use.............................................................................. 5

Target group....................................................................................5

Package content ........................................................................ 5

Technical data............................................................................ 6

Symbol description .................................................................... 6

Safety notes............................................................................... 6

For your safety by handling the transmitter and the receiver.......7

For your safety by handling the batteries ......................................8

Installation ................................................................................ 8

Connections............................................................................... 8

Power supply...................................................................................8

binding ...................................................................................... 9

Display and adjusting the receiver settings ................................ 9

Special features of the GR-16 HoTT receiver ...............................10

Firmware update ..................................................................... 12

Declaration of conformity........................................................ 14

Notes on environmental protection ......................................... 14

Care and maintenance............................................................. 14

Warranty ................................................................................. 15

4 / 16 33508_sh_V1

Introduction

Thank you very much for purchasing the Graupner receiver GR -16

HoTT.

Read this manual carefully to achieve the best results with your HoTT

system and first of all to safely control your models. If you experience

any trouble during operation, take the instructions to help or ask

your dealer or Graupner Service Centre.

Due to technical changes, the information may be changed in this

manual without prior notice. Be always updated by checking period-

ically on our website, www.graupner.de to be always uptodate with

the products and firmwares.

This product complies with national and European legal require-

ments.

To maintain this condition and to ensure safe operation, you must

read and follow this user manual and all the safety notes before

using the product!

Note

This manual is part of that product. It contains important informa-

tion concerning operation and handling. Keep these instructions for

future reference and give it to third person in case you gave the

product.

Service centre

Graupner Central Service

Graupner/SJ GmbH

Henriettenstraße 96

D-73230 Kirchheim/Teck

Servicehotline



(+49) (0)7021/722-130

Monday- Thursday:

9:15 am- 4:00 pm

Friday:

9:15 am- 1:00 pm

service@graupner.de

Graupner USA

3941 Park Dr Suite 20-571

El Dorado Hills, CA 95762

Website: www.graupnerusa.com

Phone: +1 855-572-4746

Email:[email protected]om

Graupner in Internet For the service centers outside Germany please refer to our web site

www.graupner.de.

5 / 16

33508_sh_V1

Intended use

The receiver only be used for the purpose specified by the manu-

facturer for operation of remote control models without passengers.

Any other type of use is impermissible and may damage the system

and cause significant property damage and/or personal injury. No

warranty or liability is therefore offered for any improper use not

covered by these provisions.

In addition, it is explicitly pointed out that you must inform yourself

about the laws and regulations applicable at your respective starting

point before starting the remote control operation. Such conditions

may differ from state to state, but this must be followed in every

case.

Note

Read through this entire manual before you attempt to install or use

the transmitter.

Target group

The item is not a toy. It is not suitable for children under 14. The

installation and operation of the receiver must be performed by

experienced modellers. If you do not have sufficient knowledge

about dealing with radio-controlled models, please contact an expe-

rienced modeller or a model club.

Package content

• 8 channel receiver GR-16 HoTT 2.4 GHz

• Manual

6 / 16 33508_sh_V1

Technical data

Antenna 2x cable 145 mm,

of which last 30 mm active

Operating voltage (2.5) 3.6 ... 8.4 V

Frequency range 2400 ... 2483.5 MHz

Modulation 2.4 GHz FHSS

Number of controls 8

Current consump-

tion approx. 70 mAh

Temperature range -15 … +70°C

Dimensions approx. 46 x 21 x 14 mm

Weight approx. 12 g

Symbol description

Always observe the information indicated by these warning

signs. Particularly those which are additionally marked with the

words CAUTION or WARNING.

The signal word WARNING indicates the potential for serious injury,

the signal word CAUTION indicates possibility of lighter injuries.

The signal word Note indicates potential malfunctions.

Attention indicates potential damages to objects.

Safety notes

These safety instructions are intended not only to protect the prod-

uct, but also for your own and other people’s safety. Therefore please

read this section very carefully before using the product!.

• Do not leave the packaging material lying around, this could be a

dangerous toy for children.

• Persons, including children, with reduced physical, sensory or

mental capabilities, or lack of experience or knowledge, or not

capable to use safely the receiver must not use the receiver with-

out supervision or instruction by a responsible person.

• Operation and use of radio-controlled models needs to be learnt!

If you have never driven such a model, then start extra carefully

and make sure to be familiar with the reactions of the model to

the remote control commands. Proceed responsibly.

7 / 16

33508_sh_V1

• First, always perform a range and function test on the ground (to

do so, hold your model tight), before you use your model. Repeat

the test with running motor and with short throttle bursts.

• Only use the components and spare parts that we recommend.

Always use matching, original Graupner plug-in connections of

the same design and material.

• Make sure that all of the plug-in connections are tight. When dis-

connecting the plug-in connections, do not pull the cables.

• Protect the receiver from dust, dirt, moisture and foreign parts.

It must be protected from vibration as well as excessive heat or

cold. The models may only be operated remotely in normal out-

side temperatures such as from-10°C to +55°C.

• Always use all your HoTT components only with the latest firm-

ware version.

• If you have questions which cannot be answered by the operat-

ing manual, please contact us or another expert in the field.

For your safety by handling the transmitter and the receiver

WARNING

Also while programming the transmitter, make sure that a con-

nected motor cannot accidentally start. Disconnect the fuel sup-

ply or drive battery beforehand.

CAUTION

Avoid every kind of short-circuit in all sockets of the transmitter!

Risk of fire! Use only the suitable connectors. In no case the elec-

tronic component of the transmitter or of the receiver may be

changed or modified. Due to licensing reasons, any reconstruction

and/or modification of the product is prohibited.

Note

During transport protect the model and the transmitter from dam-

ages.

8 / 16 33508_sh_V1

For your safety by handling the batteries

CAUTION

• Protect the batteries from dust, dirt, moisture, heat and vibra-

tions. Only use in dry locations.

• Do not use any damaged battery.

• Batteries may not be heated, burned, short-circuited.

• If handled improperly, there is a danger of fire, explosion, irri-

tation and burns.

• Leaked electrolyte is caustic and should not be touched or

come into contact with your eyes. In case of emergency, rinse

with a large quantity of water and consult a Med. Doctor.

• Stock the batteries in dry and fresh conditions.

• Dispose of the battery in the proper disposal centers.

Installation

The receiver must be protected against dust, exhaust gases, splash

water, etc. in the model. When you install your receiver, make sure

that it is not excessively airtight to prevent it from overheating during

operation.

Servo cables may not be wound around antennas or run next to

them. Make sure that the cables cannot shift to lie directly adjacent

to antennas during flight.

In the case of carbon fibre fuselage, at least the last 35 mm of the

antennas shall be routed from the fuselage.

Connections

Connect the devices that have to be connected to the receiver to the

row of sockets on one end of the receiver. The servo connections of

the Graupner-HoTT receiver are numbered.

The polarity of the plug-in system cannot be reversed. Do not apply

force.

Power supply

For the battery connection are designated the ports 1 and 6, they

are also provided with an additional "B". In principle, however, you

can connect a battery to any free socket. By V- or Y-cable, but also

with any remote control component. We recommend that you con-

nect the power supply to the socket(s) close to the servos already

connected to the receiver. If you wish to connect multiple separate

batteries, the batteries must be of the same nominal voltage and

capacity.

9 / 16

33508_sh_V1

Never connect different battery types or batteries with strongly dif-

ferent charges since this can cause an effect similar to a short circuit.

In such cases for safety reasons, insert voltage stabilizing elements

such as PRX-5A (No. 4136) receiver power supplies between the bat-

teries and receiver.

Attention

When selecting and connecting a power supply, be aware that

although the operating range of the receiver ranges from 3.6 to 8.4

V. However, practically all of the previously marketed servos, speed

controllers, gyros, etc. as well as many which are offered today have

a permissible operating voltage range of 4.8 to 6 V.

binding

To establish a connection with the transmitter, the Graupner HoTT

receiver must first be "bound" to at least one model memory in "its"

Graupner HoTT transmitter. This process is generally called "bind-

ing".

Binding step by step

1. Prepare the transmitter to be bound according to its instructions

for binding.

2. Switch the receiver power supply on.

The LED of the GR-16 HoTT receiver blinks in red with a slow

rhythm.

3. Push and hold for about three seconds the SET button on the

receiver.

After this time has elapsed, the LED flashes red and green simul-

taneously for a further approx. three seconds. During this time,

the receiver is in bind mode.

4. Start the transmitter-side binding according to the instructions

of the transmitter.

5. If the LED of the receiver starts to light constantly green within

approximately three seconds, the binding process has been com-

pleted successfully.

Your transmitter/receiver combination is ready for operation.

If the LED flashes slowly red, the "binding" has failed. Change the

positions of the associated antennas and try the entire proce-

dure again.

Display and adjusting the receiver settings

The settings of the receiver can be displayed with a suitable HoTT

transmitter or the SMART-BOX and some can also be changed. Refer

to the "Telemetry" section for detailed descriptions.

TELEMETRIE

EINSTELLEN,ANZEIGEN

SENSOR

ANZEIGE HF STATUS

AUSWAHL ANSAGEN

RX DATA EIN

ALARMEINSTELLUNG

10 / 16 33508_sh_V1

Special features of the GR-16 HoTT receiver

Connection 6

6CH FUNCTION

Depending on the settings in the "6CH FUNCTION" line of the "RX

DATAVIEW" page of the telemetry menu, the output 6 can be used

to connect RC components or a circuit for voltage measurement.

Carry out the changeover as described in the instructions for the

transmitter or the SMART-BOX.

• SERVO

The connection 6 is suitable for the operation of RC components.

• BATT V

After switching as described before, a DC voltage off max. 25,5 V

can be displayed instead of the receiver voltage. This way it is

possible to monitor the main battery voltage without using exter-

nal sensors. The ESCs S3082 and S3083 have this switch already

included.

s + –

50 mm

100nF

2k7Ω

22kΩ

max. 25,5 V =

100 mm

–

Attention

Never connect a power supply with an output voltage higher than

8,4 V directly to a connection port of the receiver! The receiver and

all connected devices would be immediately destroyed.

RX DATAVIEW V6.39

S–STR100% R–TEM.+28°C

L PACK TIME 00010msec

R-VOLT :05.0V

L.R-VOLT:04.5V

S–QUA100%S–dBM–030dBM

6CH FUNCTION:SERVO

Inhaltsverzeichnis

Andere GRAUPNER Empfänger Handbücher

GRAUPNER

GRAUPNER 23608 Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12L HoTT Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12L HoTT Bedienungsanleitung

GRAUPNER

GRAUPNER GR-8 HoTT Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12SH+ Bedienungsanleitung

GRAUPNER

GRAUPNER GR-18 Series Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12SC+ Bedienungsanleitung

GRAUPNER

GRAUPNER mz-24 HOTT Bedienungsanleitung

GRAUPNER

GRAUPNER XR -12DXT IFS Einrichtungshandbuch

GRAUPNER

GRAUPNER HoTT GR-18 Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12L HoTT Bedienungsanleitung

GRAUPNER

GRAUPNER GR-24PRO Bedienungsanleitung

GRAUPNER

GRAUPNER HoTT GR-18 Bedienungsanleitung

GRAUPNER

GRAUPNER mz-24 HOTT Bedienungsanleitung

GRAUPNER

GRAUPNER mz-24 HOTT Bedienungsanleitung

GRAUPNER

GRAUPNER HoTT GR-18 Bedienungsanleitung

GRAUPNER

GRAUPNER GR-10C Bedienungsanleitung

GRAUPNER

GRAUPNER HoTT GR-12L S1012 Bedienungsanleitung

GRAUPNER

GRAUPNER 33505 Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12 Bedienungsanleitung

GRAUPNER

GRAUPNER 33516 Bedienungsanleitung

GRAUPNER

GRAUPNER GR-12L SUMD+T Bedienungsanleitung

GRAUPNER

GRAUPNER 33575 Bedienungsanleitung

GRAUPNER

GRAUPNER 33575 Bedienungsanleitung

Beliebte Empfänger Handbücher anderer Marken

Garmin

Garmin GA 23 Bedienungsanleitung

Aiphone

Aiphone PS-12F Bedienungsanleitung

IMES

IMES TCS-01CA-PMI Bedienungsanleitung

BWI Eagle

BWI Eagle AIR-EAGLE SR Handbuch

AMIMON

AMIMON AMN12310 WHDI Bedienungsanleitung

Dual

Dual DMCPA79BT Betriebsanleitung

Sound Associates

Sound Associates SA652P Bedienungsanleitung

Sherwood

Sherwood NewCastle R-772 Bedienungsanleitung

Audio

Audio A10-RX Series Bedienungsanleitung

AllSee

AllSee PushShare PSRV1.1 Bedienungsanleitung

DEMAG

DEMAG DRC-DR D2 Bedienungsanleitung

Teleco

Teleco TVRCL868A02 Bedienungsanleitung

Bosch

Bosch RF3222E Bedienungsanleitung

Kramer

Kramer 631R Bedienungsanleitung

Xpress

Xpress xmc10 Bedienungsanleitung

JVC

JVC KD-MR1BTS Bedienungsanleitung

Omega Engineering

Omega Engineering UWTC-REC3 Bedienungsanleitung

e-survey

e-survey E300 Pro Bedienungsanleitung