GRAUPNER AMIGO IV Bedienungsanleitung

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Order No. 9546

Instructions

AMIGO IV

Model glider

for

bungee launch, slope soaring and electric flying

This model requires at least a two-function radio control system.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Specification

Wingspan approx. 2000 mm

Overall length approx. 1115 mm

Wing section NACA 4409

Tailplane section l Clark Y

Wing area approx. 62.47

Tailplane area approx. 7.5

Total surface area approx. 69.97

All-up weight according to

fittings, min. approx. 1110 g

Longitudinal dihedral approx. 1.5°- 2°

Centre of Gravity approx. 110 mm aft of the root leading edge,

measured on both sides of the fuselage

Notes on building the model

It is essential to read right through these instructions before starting to build the

model. Please be aware of the hazards involved in the use of tools.

Remove all traces of grease from the joint surfaces of components which are to be

glued. A good method is to sand lightly before wiping with a non-greasy liquid deter-

gent solution. Before gluing any GRP parts, and GRP fuselages in particular, the joint

surfaces must be sanded thoroughly with fine-grit abrasive paper before de-greasing

with a solvent such as acetone. This is the only method of obtaining durable glued

joints involving GRP parts.

Tools required to build the AMIGO IV

Pencil (HB lead), felt-tip pen, setsquare, tape measure or metre rule, Lexan shears,

Order No. 26, sharp, narrow-bladed knife, e.g. balsa knife, Order No. 980, small

electric drill, set of twist drills.

Gluing different materials

The following table provides a few examples of typical glued joints.

It is just a guide, and is not intended to be comprehensive.

Material Typical glued joint Adhesive

Order No.

Wood to Fin to UHU wood glue express

wood fuselage 958.60

UHU hart

534.35

Note:

Please observe the instructions provided by the adhesive manufacturers when using

their products. For more information on adhesives refer to the main FS catalogue.

Solvent-based adhesives should always be used in a well ventilated room.

Observe the manufacturer’s instructions and warnings.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Radio control system

We particularly recommend: mc-12 computer system or better

Recommended servos:

Function Type Order No.

For rudder and DES 675 BB 7940

elevator

For the receiver and transmitter batteries we recommend rechargeable packs, which

should be maintained carefully before and after each flying session. Please note that

batteries of this type do not reach full capacity until they have been charged and dis-

charged (cycled) several times.

We deliberately recommend rechargeable batteries for the receiver and transmitter,

as these types provide the widest margin of safety.

Please see the main FS catalogue for details of suitable battery chargers.

You will also need foam rubber for protecting the receiver from shock damage.

Motor pylon accessories

Item Order No.

Motor pylon 2910

INLINE 470 motor 6605

CAM PROP 1360.20.10

Precision spinner 1385.383

COMPACT FLY 25 BEC 7221

Assembling the AMIGO IV

Do not start building the model until you have studied the kit contents, and are

familiar with the components and the individual stages of construction. If you believe

you have grounds for complaint about any part, inform the model shop from whom

you purchased the kit in the first instance.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Fin and tailplane

Use your fingertips to locate the fin slot, the pushrod exits, and the openings for the

ON / OFF switch, the wing retaining dowels and the towhook. Melt the film over them

using the tip of a hot soldering iron.

Fit the fin in the exposed slot, pushing it down until it rests on the support plate

inside the fuselage. Mark the outline of the fuselage on both sides of the fin using a

felt-tip pen. Remove the fin and run a hot soldering iron along the edge of a steel

ruler positioned just below the marked line, then peel the covering film from the joint

areas.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Mark a centreline on the rudder hinges using a pencil, as shown in the photo, then

push the hinges into the slits in the fin to a depth of around 1 mm.

Push the hinges into the fin as far as the pencil-line, and glue them in place with

cyano-acrylate (“cyano”). It is best to use a syringe to apply the adhesive between

the hinge and the wood on both sides, as shown in the picture.

Allow the glue to set hard, then insert the hinges in the slits in the rudder to a depth

of about 1 mm once more.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Apply a drop of cyano on both sides of each hinge, and quickly push the rudder onto

the hinges, leaving a gap about 0.5 mm wide along the hinge-line.

The fin can now be glued in the slot in the fuselage using UHU hart or UHU wood

glue: apply glue to the support plate in the fuselage and to both sides of the fin, then

push the panel into the slot until it rests squarely on the support plate. Check that the

fin is exactly vertical, and tape it in position as shown while the glue is drying.

Drill 2 mm Ø holes for the rudder horn at the marked points on the rudder, and fix

the horn in place using two pan-head screws and the plastic spreader plate.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Use your fingertips to locate the holes for the tailplane retaining screws on both

sides of the tailplane, and melt the film over them with a hot soldering iron.

Temporarily fix the tailplane to the fuselage using the M3 x 16 socket-head screws

provided. Slip the elevator pushrod into the guide tube, working from the tail end of

the fuselage. Screw the locknut and clevis on the threaded end, and connect the

clevis to the elevator horn as shown.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Position the horn on the elevator in such a way that the linkage hole for the clevis

lines up with the elevator hinge pivot axis; mark the screw-holes on the elevator.

Fix the horn to the elevator using two pan-head screws and the spreader plate.

Use side-cutters to snip off the excess length of the horn retaining screws, and file

the ends back flush with the spreader plate.

Installing the towhook

The towhook is attached to the fuselage using two socket-head machine screws and

the plastic spreader plate provided. Don’t overtighten the screws: tighten them just to

the point where the hook is fixed securely to the fuselage, and cannot shift.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Installing the servos and the ON / OFF switch

Locate the rubber grommets and metal spacer sleeves supplied in the servo

accessory packs, and press them into the servo mounting lugs. Note that the flange

of the spacers must be at the bottom.

Fit the servos in the servo plate and drill 1.5 mm Ø pilot-holes through the

grommets. Fix the servos in place using the retaining screws supplied with them.

Cut down the servo output levers to the shape shown in the photo below.

GRAUPNER GmbH & Co. KG D-73230 KIRCHHEIM/TECK GERMANY

Modifications reserved. No liability for printing errors 12.2010

Set the servos to centre from the transmitter - check that the trims are exactly at

centre - before fitting the output arms on the output shafts. Use a felt-tip pen to mark

the position of the linkage holes on the pushrods.

Use a pair of flat-nose pliers to bend the pushrods up at right-angles at the marked

points. Snip off excess pushrod material at a point around 8 mm above the bend.

Connect the pushrods to the outermost holes in the servo output arms from the

underside, and push the plastic keepers into place to prevent them working loose.

The wings are retained on the fuselage by rubber bands stretched between

transverse aluminium tubes. Locate the dowel holes in the fuselage sides with your

fingertips, melt away the covering film using a hot soldering iron, and push the

aluminium tubes through; they should project by equal amounts on both sides.

Andere Handbücher für AMIGO IV

Andere GRAUPNER Spielzeug Handbücher

GRAUPNER

GRAUPNER SKY HERO III Bedienungsanleitung

GRAUPNER

GRAUPNER AMIGO V Bedienungsanleitung

GRAUPNER

GRAUPNER Yak 55 M Gernot Bruckmann Design Bedienungsanleitung

GRAUPNER

GRAUPNER THEODOR HEUSS model boat Bedienungsanleitung

GRAUPNER

GRAUPNER Skalar Bedienungsanleitung

GRAUPNER

GRAUPNER EXTRA 300S Bedienungsanleitung

GRAUPNER

GRAUPNER Husky 1800S Bedienungsanleitung

GRAUPNER

GRAUPNER der mini uhu 4315 Bedienungsanleitung

GRAUPNER

GRAUPNER EXTRA 300 HP Bedienungsanleitung

GRAUPNER

GRAUPNER micro NH90 indoor Bedienungsanleitung

GRAUPNER

GRAUPNER Race copter alpha 250 Q Bedienungsanleitung

GRAUPNER

GRAUPNER DIAMANT Bedienungsanleitung

GRAUPNER

GRAUPNER ALTONA Bedienungsanleitung

GRAUPNER

GRAUPNER EXTRA 300 SHP Indoor Bedienungsanleitung

GRAUPNER

GRAUPNER PITTS S12 Bedienungsanleitung

GRAUPNER

GRAUPNER 65 Bedienungsanleitung

GRAUPNER

GRAUPNER micro 47G indoor Bedienungsanleitung

GRAUPNER

GRAUPNER HYDROPOWER Bedienungsanleitung

GRAUPNER

GRAUPNER GL-39 ALBATROS Bedienungsanleitung

GRAUPNER

GRAUPNER SPEED Bedienungsanleitung

GRAUPNER

GRAUPNER MDM-1 FOX 4559 Bedienungsanleitung

GRAUPNER

GRAUPNER WIESEL Bedienungsanleitung

GRAUPNER

GRAUPNER ELEKTRO-UHU Bedienungsanleitung

GRAUPNER

GRAUPNER 9397 Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Handbuch

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

Meccano

Meccano 15103 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung