GREAT PLAINS 3P1006NT Bedienungsanleitung

Read the operator manual entirely. When you see

this symbol, the subsequent instructions and

warnings are serious - follow without exception.

Your life and the lives of others depend on it!

Illustrations may show optional equipment not

supplied with standard unit.

Table of Contents

Original Instructions 151-144B

Great Plains

MATERIAL RATE MANUAL

MODELS 3P1006NT

NO-TILL DRILL

means, including photocopying, recording, or other electronic or mechanical methods, without the prior written

permission of the publisher, except in the case of brief quotations embodied in critical reviews and certain other

noncommercial uses permitted by copyright law.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, DrillCommand, Max-Chisel, Row-Pro, Singulator

Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land

Pride, MeterCone, Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-

Trill, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and produce names that appear and are owner by others are trademarks of their respective owners.

For permission requests, write to the publisher at the address below.

Great Plains Mfg.

1525 E. North St.

P.O. Box 5060

Salina, KS 67402

You can also visit our website at www.greatplainsag.com/en/manuals/905/product-manuals for a full catalog of this

and other manuals.

Ordering Information:

Quantity sales. Special discounts are available on quantity purchases by corporations, associations, and others. For

details, contact the publisher at the address above.

Orders for personal, non-commercial use. Please contact our service department by mail or our website

www.greatplainsag.com.

3P1006NT Cover

Great Plains | 151-144B | 2019/03/14 i

Table of Contents

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Safety Information . . . . . . . . . . . . . . . . . . . . . . . . 1

Calibration Overview . . . . . . . . . . . . . . . . . . . . . 2

Calibration Crank . . . . . . . . . . . . . . . . . . . . . . . . . 2

General Calibration Procedure. . . . . . . . . . . . . . . 2

Calibration Preparation for S/N A1211W+ . . . 3

Calibration Crank Revolutions . . . . . . . . . . . . 3

Main and Dual Seed . . . . . . . . . . . . . . . . . . . . . . 5

Drive Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Seed Rate Handle . . . . . . . . . . . . . . . . . . . . . . . . 5

Seed Cup Door Settings . . . . . . . . . . . . . . . . . . . 6

Row Shutoff . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Seed Rate Chart Overview . . . . . . . . . . . . . . . . . 7

Seed Rate Calibration . . . . . . . . . . . . . . . . . . . . . 8

Calibration Procedure . . . . . . . . . . . . . . . . . . 8

Seed Rate Charts. . . . . . . . . . . . . . . . . . . . . . . . 10

Native Grass . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Native Grass Rate Calibration . . . . . . . . . . . . . . 22

Calibration Procedure . . . . . . . . . . . . . . . . . 22

Native Grass Meter Shaft Rates . . . . . . . . . . . . 25

Standard Rates . . . . . . . . . . . . . . . . . . . . . . 25

Rates with Rate Reduction Kit . . . . . . . . . . . 25

Seed Lubricant . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Brome Grass Seeding . . . . . . . . . . . . . . . . . . . . 26

Brome Rate Charts . . . . . . . . . . . . . . . . . . . . . . 28

Standard Brome Rates. . . . . . . . . . . . . . . . . 28

Reduced Brome Rates. . . . . . . . . . . . . . . . . 28

Small Seeds . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Small Seeds Rate Calibration . . . . . . . . . . . . . . 29

Calibration Procedure . . . . . . . . . . . . . . . . . 29

Small Seeds Row Shut-Off . . . . . . . . . . . . . . . . 30

Small Seeds Rate Charts. . . . . . . . . . . . . . . . . . 31

Fertilizer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Adjusting for Density . . . . . . . . . . . . . . . . . . . . . 33

Density Conversion Chart . . . . . . . . . . . . . . 33

Adjustment Procedure . . . . . . . . . . . . . . . . . 33

Fertilizer Rate Calibration. . . . . . . . . . . . . . . . . . 34

Calibration Procedure . . . . . . . . . . . . . . . . . 34

Fertilizer Rate Chart . . . . . . . . . . . . . . . . . . . 35

Cover

3P1006NT Table of Contents Introduction

Great Plains | 151-144B | 2019/03/14 1

Introduction

This Material Rate Manual assists in the proper

setting of seeding and fertilizer rates for the

3P1006NT drill.

Independent mechanisms drive the main seed,

native grass, dual seed, small seeds, and fertilizer

applications.

The rates in the charts are approximate. To assure

the most accurate seeding, it is recommended that

the drill be calibrated for the desired seed at the time

of planting.

Some setup, operation, and adjustment material in

this manual may be repeated from the drill operator

manual. You need to be thoroughly familiar with drill

operations and adjustments before applying the

information from this manual.

Many factors can affect rates including foreign

material, seed treatment, seed size, seed weight,

field conditions, humidity, tire pressure, and tire

slippage.

Safety Information

The safety symbol indicates a potential safety

hazard to persons operating or near the

machine and advises on how to avoid it.

The notice symbol indicates a potential for

machine or property damage from operator

error and advises on how to avoid misuse.

The information symbol indicates useful - but

not crucial - information for machine

operation, assembly, or adjustment.

Review the safety information in the operator manual

before calibrating or making any adjustments to the

drill.

Great Plains | 151-144B | 2019/03/14 2

3P1006NT Table of Contents Calibration Overview

Calibration Overview

Detailed calibration steps vary with each box. Some

general information applies to all boxes, and is

explained here.

Calibration Crank

The calibration crank is stored at either the top front

frame for older drills, or on the inside of the left-hand

3-point hitch for newer drills.

The retaining pin used for storage can also secure

the crank to the jackshaft.

The following table shows what is being calibrated,

serial number range, and where to locate the crank

for calibrating.

A drill with serial number A1067W and above has a

shared jackshaft connecting both gearboxes, but the

revolutions per area are different for the left and

optional right drive systems. ranking operates all

meters across the drill.

A drill with serial number A1066W and below has

independent left and optional right drive systems.

Cranking operates all meters on that side.

General Calibration Procedure

Perform the calibration with the drill hitched and

raised. Install lift-assist cylinder lock. Calibration with

the drill lowered is not recommended, as the drive

tires in contact with the ground prevent drive

operation.

Operate the crank in the tire rotation direction:

left end of drill or shaft - counterclockwise

right end of drill or shaft - clockwise

A wide range of cranking speeds produce accurate

calibrations. For reference, at 10 kph (6 mph) field

speed, jackshaft rpm is 65 (about 1 revolution per

second).

On boxes not being calibrated, empty the boxes, set

rate handles to zero, or remove a drive chain to

prevent undesired meter operation.

Serial Number

Range Use Crank At

Main

Seed

A1067W+ Left lower jackshaft

A1066W- Left upper jackshaft

Dual

Seed

A1211W+ Right lower calibration

shaft

A1067W-A1210W Right lower jackshaft

A1066W- Right upper jackshaft

Fertilizer A1067W+ Left lower jackshaft

A1066W- Left upper jackshaft

Native

Grass

A1211W+ Right lower calibration

shaft

A1067W-A1210W Right lower jackshaft

A1066W- Right upper jackshaft

Small

Seeds

A1067W+ Left lower jackshaft

A1066W- Left upper jackshaft

3P1006NT Table of Contents Calibration Overview

Great Plains | 151-144B | 2019/03/14 3

Calibration Preparation for S/N A1211W+

These instructions are for preparing to calibrate a

dual seed or native grass option.

1. Unpin the coupler (1) and slide out of the way to

disconnect the two jackshafts.

2. Make sure the 42 pitch chain (2) is installed on

the right-hand gearbox. The chain must be

routed around the 12 tooth sprocket on the

gearbox and around the 22 tooth sprocket on the

left end of the calibration shaft. Tighten the chain

with the idler.

3. Place the calibration crank (3) on the right end of

the calibration shaft (4).

Calibration Crank Revolutions

Left side cranking for S/N A1067W+

The table below applies to the main seed, optional

fertilizer, and optional small seeds. The crank

revolutions per area are independent of gearbox

drive type.

Right side cranking for S/N A1211W+

Place the calibration crank on the end of the

calibration shaft as shown.

Left Calibration Crank Revolutions

Standard Rate Acre Hectare

Full Area 310 766

1/10th Area 31 77

Right Calibration Crank Revolutions

Standard Rate Acre Hectare

Full Area 310 766

1/10th Area 31 77

Great Plains | 151-144B | 2019/03/14 4

3P1006NT Table of Contents Calibration Overview

Right side cranking for S/N A1067W - A1210W

The following charts apply to the dual seed and

native grass options. The shaft being cranked is on

the output side of the gearbox, so the cranks per

area vary with gearbox drive type.

Crank counts below 10 are not recommended.

Sample sizes may be too low.

Left and right side cranking for S/N A1066W-

Place the crank on either end of a main jackshaft at

the appropriate gearbox. See "Calibration Crank”

on page 2.

If weight brackets are installed, there is not

enough clearance at the left end of the left

side shaft. An electronic acremeter may also

be installed there.

Right Calibration Crank Revolutions

Drive

Type

Hectare Acre

Full 1/10th Full 1/10th

1169.8 17 68.7 --

2346 34.6 140.2 14.0

3520 52.0 210.4 21.0

4848 84.8 343 34.3

Reduced Rate (Native Grass Only)

Drive

Type

Hectare Acre

Full 1/10th Full 1/10th

198.4 -- 39.8 --

2200.8 20.1 81.3 --

3301.3 30.1 121.9 12.2

4491.5 49.1 198.9 19.9

Revolutions for Crank Tire

Full acre 568.7 1013.8

1/10th acre 56.9 101.4

Full Hectare 1405.3 2505.1

1/10th Hectare 140.5 250.5

3P1006NT Table of Contents Main and Dual Seed

Great Plains | 151-144B | 2019/03/14 5

Main and Dual Seed

To get the desired seed population requires four

steps:

1. selecting one of four drive types

2. setting the seed rate handle

3. positioning the seed cup door

4. checking the seeding rate

The seed rate charts are based on cleaned,

untreated seed of average size and test weight, and

on factory-supplied tires inflated to factory

specification.

The seed rate charts list the proper drive type and

seed rate handle settings for various seeds and

seeding rates.

Use the charts only as a starting point. Minor

adjustments may be required. Set and check the

seeding rate using the procedures beginning on

page 8, then adjust the rate as necessary.

Drive Types

The charts list drive types as 1, 2, 3 or 4. Drive type

is set using the handle (1) on the gearbox cover:

at left front of drill for the main seed box, and

at right front of drill for the dual seed and native

grass options.

Move the handle until the drive type number appears

in the handle window (2).

Each drive type corresponds to a specific gear ratio.

Seed Rate Handle

The seed rate handle controls the percentage of

engagement of the seed sprocket in each feed cup.

The initial setting of the handle is given by the seed

rate chart.

You can temporarily stop the main seed flow

(such as for adjusting level/depth) with the

handle set to zero.

There are separate seed rate handles for the

standard main seed and the dual seed option.

To set the handle:

1. Loosen the wing nut (1) under the handle.

2. Move the indicator (2) from the current setting to

about 10 higher than the new value, then back to

the new value.

3. Tighten the wing nut.

Drive Type Relative Speed

1Slowest

22.06 times faster than drive type 1

3 3.08 times faster than drive type 1

45.02 times faster than drive type 1

Great Plains | 151-144B | 2019/03/14 6

3P1006NT Table of Contents Main and Dual Seed

Seed Cup Door Settings

At each main seed tube, adjust the feed cup door

handle (1) for the seed size.

The handle has the following settings:

(A) Smallest seeds - wheat and similar small seeds.

(B) Soybeans and similar larger seeds.

cracking with setting B.

(D) Used for clean-out, not planting. If set to this

position with seed loaded, it may be difficult to reset

to a normal operating position.

Row Shutoff

If alternate row spacings are desired, the unused

rows can be shut off with optional feed cup plugs.

To install feed cup plugs:

1. Clean out seed. The seed box must be empty

before inserting the feed cup plugs.

2. Insert one plug at each row to be shut off. Verify

the seed hose path before inserting the plug as

some hoses do not make a vertical drop to their

row units.

3. Review seed rate settings before planting.

Perform calibration calculations with the active

row count.

Andere Handbücher für 3P1006NT

Inhaltsverzeichnis

Andere GREAT PLAINS Landwirtschaftliche Geräte Handbücher

GREAT PLAINS

GREAT PLAINS MC5109 Max-Chisel Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS BD7600 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS PL5700 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 7000 Series Leitfaden

GREAT PLAINS

GREAT PLAINS NP2540 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 1510HDP Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS NTA607HD Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Yield-Pro 3P3025AH Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Turbo Max VT1110-7.5M Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 3P606NT Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Yield-Pro Air-Pro YP2425A Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS VT1510 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Terra Max HT1100-20 Leitfaden

GREAT PLAINS

GREAT PLAINS 2SF24 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS PL5200 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Simba SL700 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS CPH Produkthandbuch

GREAT PLAINS

GREAT PLAINS 5109 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Ultra-Till I 3030 Series Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 706NT Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 3S-4000HD Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Short Disk SD2600 Leitfaden

GREAT PLAINS

GREAT PLAINS HT1110-6.0M Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS CTA4000 Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung