GREAT PLAINS Terra Max HT1100-20 Benutzerhandbuch

Manufacturing, Inc.

www.greatplainsmfg.com

ORIGINAL INSTRUCTIONS

Implement Command System

Manual

Terra Max

Read the operator’s manual entirely. When you see this symbol, the

subsequent instructions and warnings are serious - follow without

exception. Your life and the lives of others depend on it!

Illustrations may show optional equipment not supplied with standard unit.

ii Great Plains | 589-930M

Implement Command System

Machine Identification

Record your machine details in the log below. If you replace this manual, be sure to transfer this information to the new manual.

If you, or the dealer, have added Options not originally ordered with the machine, or removed Options that were originally

ordered, the weights and measurements are no longer accurate for your machine. Update the record by adding the machine weight

and measurements provided in the Specifications & Capacities Section of this manual with the Option(s) weight and

measurements.

Dealer Contact Information

Model Number

Serial Number

Machine Height

Machine Length

Machine Width

Machine Weight

Delivery Date

First Operation

Accessories

Name:

Street:

City/State:

Telephone:

Email:

WARNING: Cancer and reproductive harm - www.P65Warnings.ca.gov

California Proposition 65

Important Safety Information

12/22/2020 1

Important Safety Information

Look for Safety Symbol

The SAFETY ALERT SYMBOL indicates there is a potential

hazard to personal safety involved and extra safety precaution

must be taken. When you see this symbol, be alert and

carefully read the message that follows it. In addition to design

and configuration of equipment, hazard control and accident

prevention are dependent upon the awareness, concern,

prudence and proper training of personnel involved in the

operation, transport, maintenance and storage of equipment.

Be Aware of Signal Words

Signal words designate a degree or level of hazard seriousness.

DANGER indicates an imminently hazardous situation which,

if not avoided, will result in death or serious injury. This signal

word is limited to the most extreme situations, typically for

machine components that, for functional purposes, cannot be

guarded.

WARNING indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury, and

includes hazards that are exposed when guards are removed. It

may also be used to alert against unsafe practices.

CAUTION indicates a potentially hazardous situation which,

if not avoided, may result in minor or moderate injury. It may

also be used to alert against unsafe practices.

Use Adequate Lifting Means

The frame sections and gangs of this machine are

extremely heavy. If using multiple lifters, make sure each

is rated for at least its share of the load.

Prepare for Emergencies

Be prepared if a fire starts

Keep a first aid kit and fire extinguisher handy.

Keep emergency numbers for doctor, ambulance, hospital

and fire department near phone.

Be Familiar with Safety Decals

Read and understand the “Safety Decals” section of the

Operators Manual.

Read all instructions noted on the decals.

Keep decals clean. Replace damaged, faded and illegible

decals.

2 Great Plains | 589-930M

Implement Command System, Terra Max

Wear Protective Equipment

Wear protective clothing and equipment.

Wear clothing and equipment appropriate for the job.

Avoid loose-fitting clothing.

Because prolonged exposure to loud noise can cause

hearing impairment or hearing loss, wear suitable

hearing protection such as earmuffs or earplugs.

Because operating equipment safely requires your full

attention, avoid wearing entertainment headphones while

operating machinery.

Avoid High Pressure Fluids

Escaping fluid under pressure can penetrate the skin, causing

serious injury.

Avoid the hazard by relieving pressure before

disconnecting hydraulic lines.

Use a piece of paper or cardboard, NOT BODY PARTS, to

check for suspected leaks.

Wear protective gloves and safety glasses or goggles when

working with hydraulic systems.

If an accident occurs, seek immediate medical assistance

from a physician familiar with this type of injury.

Use Safety Lights and Devices

Slow-moving tractors and towed implements can create a

hazard when driven on public roads. They are difficult to see,

especially at night.

Use flashing warning lights and turn signals whenever

driving on public roads.

Use lights and devices provided with implement.

Keep Riders Off Machinery

Riders obstruct the operator’s view. Riders could be struck by

foreign objects or thrown from the machine.

Never allow children to operate equipment.

Keep all bystanders away from machine during operation.

Shutdown and Storage

Lower implement, put tractor in park, turn off engine, and

remove the key.

Secure Hydraulic Reel Attachment using blocks and

supports provided.

Detach and store Hydraulic Reel Attachment in an area

where children normally do not play.

Important Safety Information

12/22/2020 3

Tire Safety

Tire changing can be dangerous and should be performed by

trained personnel using correct tools and equipment.

When inflating tires, use a clip-on chuck and extension

hose long enough for you to stand to one side–not in front

of or over tire assembly. Use a safety cage if available.

When removing and installing wheels, use wheel-handling

equipment adequate for weight involved.

Safety At All Times

Thoroughly read and understand the instructions in this

manual before operation. Read all instructions noted on the

safety decals.

Be familiar with all machine functions.

Operate machinery from the driver’s seat only.

Do not leave machine unattended with tractor engine

running.

Do not stand between the tractor and machine during

hitching.

Keep hands, feet and clothing away from power-driven

parts.

Wear snug-fitting clothing to avoid entanglement with

moving parts.

Watch out for wires, trees, etc., when folding and raising

machine. Make sure all persons are clear of working area.

4 Great Plains | 589-930M

Implement Command System, Terra Max

Introduction

The Implement Command System has been designed with care

and built by skilled workers using quality materials. Proper

setup, maintenance, and safe operating practices will help the

customer get years of satisfactory use from this system.

Description of Unit

The new Implement Command system now gives Terra Max

owners access to more data and technology. The Implement

Command System gives producers the data needed to make

decisions about their fields, while making real-time

adjustments to improve yields and soil health. Available on

20'-40’ Terra Max models, the Implement Command

System (ICS) allows you to take command of all your

adjustment and monitoring needs right at your fingertips. Set,

adjust, and monitor your Terra Max right on your ISO-

compatible monitor in your tractor cab.

Using This Manual

This manual will familiarize you with

safety, assembly, operation,

adjustments, troubleshooting, and

maintenance. Read this manual and

follow the recommendations to help

ensure safe and efficient operation.

The information in this manual is current at printing. Some

parts may change to assure top performance.

Definitions

The following terms are used throughout this manual.

A crucial point of information related to the preceding topic.

Read and follow the directions to remain safe, avoid serious

damage to equipment and ensure desired field results.

Useful information related to the preceding topic.

Further Assistance

Great Plains Manufacturing, Inc. wants you to be satisfied

with your new Terra Max. If for any reason you do not

understand any part of this manual or are otherwise dissatisfies

with the product please contact:

Great Plains Service Department

1525 E. North St.

PO Box 5060

Salina, KS 67402-5060

Or go to www.greatplainsag.com and follow the contact

information at the bottom of your screen for our service

department.

Figure 1

Implement Command System

TP-69747

Assembly

12/22/2020 5

Assembly

Implement Command System

Refer to Figure 2

The Controller Assembly will be shipped in a container, with

the installation hardware and will need installed on the top of

the brace bar, on the left hand side of the center brace bar.

Implement Command Wiring Harness

The wiring may need to be routed and installed on the frame of

the machine. The wiring harness is labeled near each of the

connectors to indicate which sensor or solenoid it is to be

plugged into. See “Wiring Connections Layout” on page 20.

Refer to Figure 3 & 4

Plug-in the hitch harness into the tractor and the other end into

the ICS Control Box located on the front of the left hand side

of the machine. Be sure the ICS box orientation is correct, the

openings for the plugs will be facing the inside of the machine

as shown in the parts manual.

The frame harness will plug into the ICS Control box and then

run to the other connections on the rest of the machine. It will

run under the frame tube and over to the valves.

Figure 2

ICS Controller Assembly

TP-69568

Figure 3

ICS Hitch Harness

TP-69555

Figure 4

ICS Hitch Harness

TP-69556

6 Great Plains | 589-930M

Implement Command System, Terra Max

Refer to Figure 5 & 6

The cylinder that is located on the hitch will be connected to

the FAS1wire on the harness. The harness will run under the

cylinder, thru the “ears” that connect to the H-bracket and

towards the center frame.

Refer to Figure 7

The gang angle is located on the right hand side of the front

brace bar, the wiring harness is labeled as GAS this will route

along the rear of the tube and be connected using p-clamps to

the bolts that are welded to the frame.

You may have to install the sensor on to the gauge bracket, use

the #10 x 214 bolts and hardware to install as shown.

Install the sensor in orientation shown and the small white

dot must be positioned toward the angle gauge when it is

installed on to the bracket. If not the sensor will not

function correctly and may cause dame to the machine.

Figure 5

Hitch Cylinder

TP-69547

Figure 6

Hitch Wiring

TP-69553

Figure 7

Gang Angle

TP-69548

TP-69779

Assembly

12/22/2020 7

Refer to Figure 8

The Down Pressure Valve (1) (for the finisher down pressure) is plugged into Finisher DPT1, Finisher DPT3, Finisher and DPC1,

on the frame harness. The Down Pressure Valve (2) (for the wing down pressure) is plugged into DPT1, DPT3, and DPC1, on the

frame harness. The Depth Control Valve (3) is attached to DCC1 and DCC2 harness plugs. After being attached to the Down

Pressure (1 & 2) and Depth Control Valve (3) the hydraulic hoses and the wiring harness will be routed along the left side brace

bar and to the left side of the torque tube, See Wiring Connections Layout for routing. Be sure to keep any excess wiring away

from pinch points. Use hose wrap or zip ties if needed. Wiring harness will be labeled with connection names, match the labels on

the valves with the labels on the harness.

TP-69739

TP-69784

Figure 8

Down Pressure & Depth Control Valves

TP-69743

TP-69798

HT1100-40 HT1100-40

8 Great Plains | 589-930M

Implement Command System, Terra Max

Refer to Figure 9

The Splitter Valve is attached on the right hand side of the center

brace bar. The Splitter valve is attached to SVC1 and SVC2 on

the center frame harness.

Refer to Figure 10

If the machine does not have proximity sensors then there will

be jumper plugs that must be in place on those harness

connections. These will come installed in the harness, but

please note that they must be in place. This may be a trouble

shooting point if you have issues in the future.

If your machine has proximity sensors (installed on Models

HT1100-30 & HT1100-40) then the harness will route out along

the center frame following the hydraulic hose route, using zip

ties or p-clamps to secure it to the hydraulic hoses and connect

to the sensors. These plugs are labeled as ProxLH and ProxRH.

Be sure to run them out to the correct wings. If not already

installed, the proximity sensors may need to be installed into the

brackets on the wing hinges. See parts manual for proper

adjustment.

Figure 9

Splitter Valve

TP-69557

Figure 10

Wing Wiring Route

TP-69559

Andere Handbücher für Terra Max HT1100-20

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GREAT PLAINS Landwirtschaftliche Geräte Handbücher

GREAT PLAINS

GREAT PLAINS TSF1080 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS NO-TILL Air DRILL Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS PL5500 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Nutri-Pro NP30L Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Plains Plow Series II Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Nutri-Pro NP40A Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 3S-4010HDF Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Ultra-Till I 3030 Series Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Yield-Pro 3PYPA Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 2S-2600 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS CTA4000 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Terra Max HT1100-10 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 2SF24 Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS BD7600 Leitfaden

GREAT PLAINS

GREAT PLAINS Turbo-Max 6.0M Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Yield-Pro 3P4025AH Leitfaden

GREAT PLAINS

GREAT PLAINS 3S-5000 Series Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS Short Disk SD2600 Leitfaden

GREAT PLAINS

GREAT PLAINS Turbo Max 3.0M Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS 7323DH Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS SPARTAN II Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS VT1100 Turbo Max Bedienungsanleitung

GREAT PLAINS

GREAT PLAINS PL5500 PTO Handbuch

GREAT PLAINS

GREAT PLAINS Yield-Pro 3P3025AH Bedienungsanleitung

Beliebte Landwirtschaftliche Geräte Handbücher anderer Marken

GSi

GSi PNEG-2314 Bedienungsanleitung

Checchi & Magli

Checchi & Magli TEXDRIVE Bedienungsanleitung

Amazone

Amazone Cenius 4003-2TX Bedienungsanleitung

MASSEY FERGUSON

MASSEY FERGUSON MF 9313S Bedienungsanleitung

Cima

Cima BLITZ Bedienungs- und Wartungsanleitung

Amazone

Amazone CombiDisc 3000 Montageanleitung

HE-VA

HE-VA Disc-Roller XL Contour Bedienungsanleitung

AGT

AGT AGT-SSFM Bedienungsanleitung

Milestone

Milestone 72-84 Bedienungsanleitung

KUHN

KUHN Hector 3000 Bedienungsanleitung

Krone

Krone X-Disc 6200 Bedienungsanleitung

Eliet

Eliet DZC450 Bedienungsanleitung

Taarup

Taarup BIO+ B4000 Bedienungsanleitung

Garland

Garland SHAKER 310 DPG Bedienungsanleitung

stable comfort

stable comfort StableWall System Bedienungsanleitung

Raven

Raven AccuBoom Bedienungsanleitung

International

International 710 Bedienungsanleitung

Ashland

Ashland HDW-3217-14 Bedienungsanleitung