Greenheck Sure-Aire 384986 Bedienungsanleitung

Installation, Operation and Maintenance Manual

Please read and save these instructions for future reference. Read carefully before attempting to assemble,

install, operate or maintain the product described. Protect yourself and others by observing all safety

information. Failure to comply with instructions could result in personal injury and/or property damage!

Sure-Aire™ Flow Monitoring System

General Information

This instruction manual provides installation, operating,

maintenance, and parts information for Sure-Aire™

Series Differential Pressure Controllers.

WARNING

Improper installation, adjustment, alterations, service

or maintenance can cause injury and property

damage, as well as possible voiding of factory

warranty. No person may install, operate, or maintain

the Sure-Aire Differential Pressure Controller(s)

and transmitters without ﬁrst being fully trained

and qualiﬁed in the installation, operation and

maintenance, and carefully reading and understanding

the contents of this manual. If you have any

questions about these instructions, contact your local

representative.

CAUTION

Risk of electrical shock! More than one disconnect

switch may be required to de-energize the equipment

before servicing.

Differential Pressure Controller Features:

• NEMA-4 and IP56 enclosure rating

• Factory calibrated

• 24 Vdc or 24 Vac input voltage

• Pressure ranges:

0-8.30 inches W.C.

0-22.14 inches W.C.

0-41.52 inches W.C.

0-83.04 inches W.C.

0-138.40 inches W.C.

• Selectable isolated output transmitter linear to

differential pressure

4-20 mA

2-10 Vdc

• LCD display with user-friendly touch panel interface

• Temperature compensation

• Remote duct temperature sensor

• Programmable elevation

• English or metric readings

• Simple installation

Table of Contents

General Information . . . . . . . . . . . . . . . . . . 1

Differential Pressure Controller Features. . . . . . . . 1

Installation . . . . . . . . . . . . . . . . . . . . . . . 2

Dimensions and Hole Mounting Patterns . . . . . . 2

Wiring and System Components . . . . . . . . . . 2

Label and Order Information . . . . . . . . . . . . 2

Sure-Aire Controller Part Number . . . . . . . . . . 2

Display Setting Options and Setup . . . . . . . . . 3-4

4-20 mA Transmitter Calibration Procedure . . . . . . 5

2-10 Vdc Transmitter Calibration Procedure. . . . . . 6

Temperature Sensor . . . . . . . . . . . . . . . . . . 7

Speciﬁcations . . . . . . . . . . . . . . . . . . . . . 7

Maintenance Log. . . . . . . . . . . . . . . Backcover

Our Commitment. . . . . . . . . . . . . . . Backcover

Document 476092

Sure-Aire™ Flow Monitoring System

User and Service Manual

2Sure-Aire™ Flow Monitoring System

Installation

1. Mount the controller in the vertical plane using four

#8-32 screws. Open the front cover by unscrewing

the two captive thumb screws to gain access to the

four mounting locations pictured at right.

Note: Mount the Sure-Aire controller within 75 feet

of the termination plate on the fan.

2. Use 1/4-inch nylon tubing to connect the

corresponding high and low, 1/4-inch quick connect,

pressure ports of the Sure-Aire controller to the high

and low pressure ports of the termination plate on

the fan.

3. Remove terminal block TB1 and perform wiring for

the pins listed below. For liquid tight applications,

use only 1/2-inch liquid tight conduit.

Terminal Block TB1: Input Power

Pin 1 = 24V, AC or DC (+ or -)

Pin 2 = 24V, AC or DC (+ or -)

Pin 3 = Earth Ground

4. Provide power to the controller to turn it on.

5. Select the desired Output Signal of the controller

for the Building Automation System. Use the touch

screen to select the 4-20 mA or 2-10 Vdc output

signal via the controller’s setup menu. (Refer to

Display Setting Options and Setup section, Output

Signal, pages 3 and 4).

6. Wire TB2 appropriately for the selected Output

Signal in Step 5.

Terminal Block TB2: Transmitter/Temperature

Sensor

Pin 1 = 4-20 mA or 2-10 Vdc (+) (output)

Note: 4 to 20 mA requires a load resistor

200-900 ohms

Pin 2 = 4-20 mA or 2-10 Vdc (-) (output)

Pin 3 = Shield

Pin 4 = Remote Temperature Sensor (input)

Pin 5 = Remote Temperature Sensor (input)

Note: Signal isolator may be required when two or

more output signals share a common connection at

the PLC/controller.

7. If temperature compensation is desired, mount the

provided temperature sensor in contact with the

airstream. Wire the temperature sensor into TB2

and change Temperature Comp to “Yes” via the

controller’s setup menu.

8. When the above steps are completed, make sure the

front cover is properly aligned to the housing and the

two captive thumb screws are securely tightened.

Part Number Description

384986 CNTRL,SURE-AIRE,0-8.3

384987 CNTRL,SURE-AIRE, 0-22.14

384988 CNTRL,SURE-AIRE, 0-41.52

384989 CNTRL,SURE-AIRE, 0-83.04

384990 CNTRL,SURE-AIRE, 0-138.40

Label and Order Information

The label providing details pertaining to the purchase

order is located on the inside cover of the controller.

Equipment

for

Measurement

Schofield, WI 54476 U.S.A.

Description: CNTRL,SURE-AIRE,0-22.14”

Fan Model: QEP Fan Size: 36

K Factor: 1967 Elevation: 1100

P/N: 384987 Sales Order: 6606573

Tag Mark: SF-1 P.O.#0843 Date Code: 8/12

24 Volts

AC or DC

6VA Max

Input Power

Earth Ground

~24 V

TB1

4 to 20 mA/

2-10 Vdc (+)

4 to 20 mA/

2-10 Vdc (-)

Shield

Temperature

Sensor

Load Resistance

200-900 Ohms

TB2

4-5/32 in.

(105.6 mm)

5-3/8 in.

(136.5 mm)

3-9/32 in.

(83.3 mm)

5 in.

(127 mm)

Dimensions and Hole Mounting Pattern

Wiring and System Components

Temperature Sensor

Shield

4-20 mA / 2-10 Vdc (-)

4-20 mA / 2-10 Vdc (+)

24V, AC or DC

Earth Ground

High

Pressure

Port

Reset Button

Low

Pressure

Port

TB1 TB2

WARNING

When wiring the instrument, you must follow industry

standard practices for control and protection against

electrostatic discharge (ESD). Failure to exercise good

ESD practices may cause damage to the controller.

Sure-Aire™ Flow Monitoring System

K Factor: Press Edit to

change K Factor. Press

Inc or Dec to adjust, then

press Enter to store the

value.

• 200 to 30,000

Greenheck

Sure-Aire V 1.00

K Factor:

200

Exit Inc Dec Edit /

Enter

Pressure Units: Press

Edit to change pressure

units. Press Prev or Next

to adjust, then press

Enter to store the value.

• In WC (default)

• Ft WC

• mm WC

• cm WC

• PSI

• In Hg

• mm Hg

• mBar

• PA

• KPA - kilopascals (1kPa = 1000 Pa)

• HPA - hectopascals (1 hPa = 100 Pa)

• Oz In.

Greenheck

Sure-Aire V 1.00

Pressure Unit:

In WC

Exit Prev Next Edit /

Enter

Measurement System:

Press Edit to change.

Press Prev or Next to

adjust, then press Enter

to store the value.

• English (default)

• Metric

Greenheck

Sure-Aire V 1.00

Measurement System:

English

Exit Prev Next Edit /

Enter

The following display setting options can be changed in

the Setup menu of the controller:

Display Setting Options and Setup

Menu Options: Current

settings are displayed

in the main display area

of the screen. To review

current settings, press Up

or Down to scroll through

the various controller

settings as outlined

below. Press Home to

return to the main screen.

• Elevation

• X-Mitter (output signal)

• Software Version

• K-Factor

• Sensor Installed

• Differential Pressure Measurement

• Sure-Air Controller Temperature

• Flow Temperature

• Flow Rate Measurement

• Air Density

Greenheck

Sure-Aire V 1.00

0.0010 CFM

3.96 mA

Setup Up Down Home

Sure-Aire Controller

LCD Touch Display

Air Flow Units: Press

Edit to change Air Flow

Units. Press Prev or Next

to adjust, then press

Enter to store the value.

• CFM (default)

• m3/hr

• m3/min

Greenheck

Sure-Aire V 1.00

Air Flow Unit:

CFM

Exit Prev Next Edit /

Enter

Main Display Value:

Press Edit to change

Main Display Value.

Press Prev or Next to

adjust, then press Enter

to store the value.

• Flow (default)

• Pressure

• Temperature

• Air Density

• Output Signal

• None

Greenheck

Sure-Aire V 1.00

Main Display Value:

Flow

Exit Prev Next Edit /

Enter

Secondary Display:

Press Edit to change

Secondary Display. Press

Prev or Next to adjust,

then press Enter to store

the value.

• Flow

• Pressure

• Temperature

• Air Density

• Output Signal (default)

• None

Greenheck

Sure-Aire V 1.00

Secondary Display Value:

Output Signal

Exit Prev Next Edit /

Enter

4Sure-Aire™ Flow Monitoring System

Output Signal: Press

Edit to change Output

Signal type. Press Prev or

Next to adjust, then press

Enter to store the value.

• 4-20 mA (default)

• 2-10 Vdc

Note: Output signal

is linear to differential

pressure. The equation

provided on the Sure-Aire label adhered to the fan must

be used to calculate volume.

Greenheck

Sure-Aire V 1.00

Output Signal:

4-20 mA

Exit Prev Next Edit /

Enter

Transmitter Min Value:

Press Edit to change

Transmitter Min Value.

Press Inc or Dec to

adjust, then press Enter

to store the value.

NOTE: See Transmitter

Calibration

Greenheck

Sure-Aire V 1.00

Transmitter Min Value:

1827

Exit Inc Dec Edit /

Enter

Transmitter Max Value:

Press Edit to change

Transmitter Max Value.

Press Inc or Dec to

adjust, then press Enter

to store the value.

NOTE: See Transmitter

Calibration

Greenheck

Sure-Aire V 1.00

Transmitter Max Value:

720

Exit Inc Dec Edit /

Enter

Temperature

Compensation:

Press Edit to

change Temperature

Compensation. Press

Prev or Next to adjust,

then press Enter to store

the value.

• Yes (default)

• No

Note: If temperature compensation is set to ‘No’, the

air density will be a function of standard temperature

(70°F/21°C).

Greenheck

Sure-Aire V 1.00

Temperature Comp:

Yes

Exit Prev Next Edit /

Enter

Display Brightness:

Press Edit to change

brightness. Press Inc or

Dec to adjust, then press

Enter to store the value.

• 10 - 100%

(80% default)

Greenheck

Sure-Aire V 1.00

Display Brightness %:

Exit Inc Dec Edit /

Enter

Elevation: Press Edit to

change elevation. Press

Inc or Dec to adjust, then

press Enter to store the

value.

• 0 - 10,000 ft

(0 ft default)

Greenheck

Sure-Aire V 1.00

Elevation:

800ft

Exit Inc Dec Edit /

Enter

WARNING

Due to load resistance change from product to

product, it may be necessary to recalibrate the

4-20mA transmitter. See 4-20 mA calibration

procedure.

Sure-Aire™ Flow Monitoring System

NOTE

Apply a vacuum to the High Port and the 4-20 mA

transmitter will track the span of the pressure range.

i.e. The Sure-Aire controller with a pressure sensor

of 0 - 41.51 in. W.C. installed, 4.00 mA = 0 in. W.C.,

20.00 mA = 41.52 in. W.C.

WARNING

Due to load resistance change from product to

product, it may be necessary to recalibrate the

4-20mA transmitter.

4-20 mA Transmitter Calibration

Procedure

1.0 Test Equipment

1.1 Digital Multimeter. Set multimeter to read

mA DC

1.2 Load resistor. Select a series Load Resistor

between 200 and 900 ohms.

2.0 Interconnect Wiring

24 Volts

AC or DC

6VA Max

Input Power

Earth Ground

~24 V

TB1

4 to 20 mA/

2-10 Vdc (+)

4 to 20 mA/

2-10 Vdc (-)

Shield

Temperature

Sensor

Load Resistance

200-900 Ohms

TB2

2.1 Validate the controller is setup for 4-20 mA output

signal.

2.2 Validate the power is off on the DC power supply

and the Sure-Aire controller.

2.3 Validate the multimeter is set to read mA DC.

2.4 Select a series Load Resistor between 200 and

900 ohms and install one end to TB2-1.

2.5 Interconnect the multimeter (+) probe to the other

end of the load resistor.

2.6 Interconnect the multimeter (-) probe to TB2-2 to

complete the current loop.

2.7 Apply power to the Sure-Aire controller.

2.8 Press the Setup button on the Touch Panel

interface.

2.9 Keep pressing Next button until you reach the

Transmitter Min Value screen.

2.10 Press Edit, then Inc or Dec until the digital

multimeter reads exactly 4.00 mA.

2.11 Press Enter to store the new value.

2.12 Press Next.

2.13 Transmitter Max Value.

2.14 Press Edit, then Inc or Dec until the digital

multimeter reads exactly 20.00 mA.

2.15 Press Enter to store the new value.

2.16 Press Exit to return to the main screen.

2.17 4-20 mA transmitter calibration completed.

Greenheck

Sure-Aire V 1.00

0.0010 CFM

3.96 mA

Setup Up Down Home

Sure-Aire Controller

LCD Touch Display

Greenheck

Sure-Aire V 1.00

Transmitter Min Value:

1827

Exit Inc Dec Enter

Greenheck

Sure-Aire V 1.00

Transmitter Max Value:

720

Exit Inc Dec Enter

6Sure-Aire™ Flow Monitoring System

2-10 Vdc Output Signal Transmitter

Calibration Procedure

4 to 20 mA/

2-10 Vdc (+)

4 to 20 mA/

2-10 Vdc (-)

Shield

Temperature

Sensor

TB2

24 Volts

AC or DC

6VA Max

Input Power

Earth Ground

~24 V

TB1

Sure-Aire Controller

LCD Touch Display

1.0 Test Equipment

1.1 Digital multimeter. Set multimeter to read DC

voltage.

1.2 Make sure Output Signal type is set to 2-10 Vdc.

2.0 Interconnect Wiring

Greenheck

Sure-Aire V 1.00

Output Signal:

2-10v

Exit Prev Next Edit

2.1 Validate the power is off on the DC power supply

and the Sure-Aire controller.

2.2 Validate the multimeter is set to read DC voltage.

2.3 Interconnect the multimeter (+) probe to TB2 pin 1.

2.4 Interconnect the multimeter (-) probe to TB2 pin 2.

2.5 Apply power to the Sure-Aire controller.

2.6 Press the Setup button on the Touch Panel

Interface.

2.7 Keep pressing the Next button until you reach the

Transmitter Min Value screen.

2.8 Press Edit, then Inc or Dec until the digital

multimeter reads exactly 2.00 Vdc

2.12 Press Edit, then Inc or Dec until the digital

multimeter reads exactly 10.00 Vdc.

2.13 Press Enter to store the new value.

2.14 Press Exit to return to the main screen

2.15 2-10 Vdc transmitter calibration completed.

2.9 Press Enter to store the new value.

2.10 Press Next.

2.11 Transmitter Max Value.

Greenheck

Sure-Aire V 1.00

Transmitter Min Value:

1827

Exit Inc Dec Enter

Greenheck

Sure-Aire V 1.00

Transmitter Max Value:

720

Exit Inc Dec Enter

NOTE

Apply a vacuum to the High Port and the 2-10 Vdc

transmitter will track the span of the pressure range.

i.e. The Sure-Aire controller with a pressure sensor

of 0 - 41.51 in. W.C. installed, 2.00 Vdc = 0 in. W.C.,

10.00 Vdc = 41.52 in. W.C.

Sure-Aire™ Flow Monitoring System

Temperature Sensor

Interconnect the remote temperature sensor by

connecting the temperature sensor to pins 4 and 5 of

TB2. The Remote Temperature Sensor will adjust the

air density value in the controller based on the sensor

measurement when Temperature Compensation is set

to ‘Yes’. This density compensation will affect the ﬂow

rate accordingly. If Temperature Compensation is set to

‘No’, the air density value will be a function of standard

air (70°F/21°C).

Speciﬁcations

Service: Air and non-combustible,

compatible gases

Enclosure Rating: NEMA-4 and IP56

Dimensions: 5 x 5-3/8 x 2-1/2 inches

(127 x 136.5 x 63.5 mm)

Mounting: Mount unit in vertical plane

with #8-32 screws

(4 hole locations)

Accuracy: ±0.5% full pressure scale at

77°F (25°C)

Thermal Effects: 0.015% / °F (0.027% / °C) from

-13° thru 185°F (25° thru 85°C)

Stability: < ±1% per year

Max. Pressure Limit: 72 psi (1993 inches W.C.)

Temperature Limits: 32° to 140°F (0 to 60°C)

Power Requirements: 24 Vdc or 24 Vac input voltage

Power Consumption: Power = 6VA

Output Signal: User selectable. 4-20 mA (900

ohms max.) or 2-10 Vdc

Connections: Euro-type removable terminal

blocks with 1/2 inch watertight

conduit ﬁttings.

Pressure Connections: 1/4 inch quick connect

Weight: 1.5 lbs.

Agency Approvals: ETL #3192905