Greenlee ANM-50 Bedienungsanleitung

ANM-50

ANEMOMETER

AND

THERMOMETER

ANEMÓMETRO

TERMÓMETRO

ANEMOMETRE

THERMOMETRE

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and safety infor-

mation in this manual before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre

seguridad que aparecen en este manual, antes de manejar esta

herramienta o darle mantenimiento.

Lire attentivement et bien comprendre toutes les instructions

et les informations sur la sécurité de ce manuel avant d‘utiliser

ou de procéder à l‘entretien de cet outil.

KEEP THIS MANUAL

Description

The Greenlee ANM-50 Anemometer and Thermometer is a hand-held testing

device for measuring three different characteristics: velocity (speed), flow

(volume of air per unit of time), and temperature. Useful for checking the output

of HVAC/R systems, the ANM-50 can take single-location measurements or

multiple-location measurements.

The ANM-50 can display either metric or U.S. units of measure.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment.

This instruction manual and any markings on the tool provide information for

avoiding hazards and unsafe practices related to the use of this tool. Observe all

of the safety information provided.

Purpose

This instruction manual is intended to familiarize all personnel with the safe

operation and maintenance procedures for the Greenlee ANM-50 Anemometer

and Thermometer.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

ANM-50

Important Safety Information

Read and understand this material before operating or

servicing this equipment. Failure to understand how to

safely operate this tool can result in an accident

causing serious injury or death.

This symbol is used to call your attention to hazards or unsafe practices

which could result in an injury or property damage. The signal word,

defined below, indicates the severity of the hazard. The message after the

signal word provides information for preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury or

death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or

property damage.

Important Safety Information

Electric shock and fire hazard:

•Do not expose this unit to rain or moisture.

•Do not use the unit if it is wet or damaged.

•

Use this unit for the manufacturer’s intended purpose only, as described in

this manual. Any other use can impair the protection provided by the unit.

Failure to observe these warnings can result in severe injury or death.

•Do not operate with the case open.

•Before opening the case, shut off the unit.

Failure to observe these warnings can result in severe injury or death.

Electric shock hazard:

Contact with live circuits can result in severe injury

or death.

•Do not attempt to repair this unit. It contains no user-serviceable parts.

•Do not expose the unit to extremes in temperature or high humidity.

See Specifications.

Failure to observe these precautions can result in injury and can damage

the unit.

ANM-50

Identification

1. Sensor Vane with thermocouple

2. Display LCD

3. ON-OFF RESET Press to turn the unit on or off

4. MODE VELOCITY Use for calculating airflow (see Advanced Functions)

FREE AREA FLOW

5. HOLD Press to hold the present measurement on the display;

press again to return to the normal display mode

6. AVERAGE Press to take measurements at several locations

MULTI-POINT (see Advanced Functions)

7. SEL: -MPH Press to select one of the various measurement units

-KNOTS (see Basic Functions)

8. MIN/MAX REC Press to take measurements at a single location

SINGLE-POINT (see Basic Functions)

Display Icons

9. 0000 Velocity or Flow

Measurement

10. vel Velocity

11. FLOW Airflow

12. AREA Free Flow Area

–used for

computing airflow

13. Hold Hold Function

is enabled

14. knots Knots

15. ft/m Feet per Minute

16. ft2Area in Square Feet

17. m/s Meters per Second

18. m2Area in Square Meters

19. mil/h Miles per Hour

20. cfm Cubic Feet per Minute

21. km/h Kilometers per Hour

22. cms Cubic Meters per Second

23. MIN Minimum Measurement

24. MAX Maximum Measurement

25. REC Record Mode is enabled

26. AVG Average Measurement

27. -100.0 Temperature Measurement

28. °C Celsius Scale is selected

29. °F Fahrenheit Scale is selected

vel FLOW AREA HOLD

˚C

˚F

PH knots

MIN

MAX

REC

AVG

ft/m

m/s

mil/h

km/h

ft2

cfm

cms

11 12 13 15 14

ANM-50

20°

Operation

1. Turn the unit on. After performing a self-test, the unit will display the

temperature and air velocity.

2. If the unit does not function as expected, replace the battery.

3. If the unit still does not function as expected, send the unit to Greenlee for

repair. See the address shown under Warranty.

4. See Basic Functions and Advanced Functions for detailed operating

instructions.

Typical Measurement

•Place the unit in the airstream. For highest accuracy, ensure that the airstream

and the sensor are aligned (±20 degrees maximum) as shown.

•Allow at least three seconds for the reading to stabilize.

Electric shock hazard:

Contact with live circuits can result in severe injury

or death.

Basic Functions

Metric and U.S. Measurement Scales

Use this procedure to select either metric scale (Celsius for temperature and

meters per second for airflow) or the U.S. scale (Fahrenheit for temperature and

feet per minute for airflow).

1. Turn the unit off.

2. Press the AVERAGE MULTI-POINT button and hold.

3. Press the ON-OFF RESET button and release.

4. Release the AVERAGE MULTI-POINT button after the LCD shows the

measurement scales.

5. Press the AVERAGE MULTI-POINT button to select the U.S. scale.

Press HOLD to select the metric scale.

6. Press the MIN/MAX REC button and release. The letter “S”will appear on the

display.

7. Press HOLD and release. A four-digit number will appear on the display.

8. Press the MIN/MAX REC button and release. The letter “S”will appear on the

display.

9. Press HOLD and release. The display will return to normal.

Measurement Units

In addition to selecting a measurement scale (metric or U.S.), you may also

select one of several measurement units. After turning the unit on, press and

release the SEL: -MPH -KNOTS key to cycle through the choices:

The choices will appear in this order:

• Metric: Meters per Second

•

Kilometers per Hour

•

Knots

• U.S.: Feet per Minute

•

Miles per Hour

•

Knots

ANM-50

Basic Functions (cont’d)

Air Velocity or Temperature Measurement (Single Location)

1. Turn the unit on. When “vel”appears in the upper left corner and the

temperature appears in the lower right corner, the unit is ready to take a

measurement.

2. Place the unit in the airstream.

Minimum, Maximum, and Average (Single Location)

1. If the unit is on, press and hold the MIN/MAX REC SINGLE-POINT button

until the unit beeps twice to erase any stored data.

Turn the unit on. When “vel”appears in the upper left corner and the

temperature appears in the lower right corner, the unit is ready to take a

measurement.

2. Place the unit in the airstream.

3. Press the MIN/MAX REC SINGLE-POINT button.

REC and AVG will appear on the display.

4. Press the HOLD button before removing the unit from the airstream.

5. Press the MIN/MAX REC SINGLE-POINT button to review the stored data,

which will appear in this order:

* Instantaneous Measurement •Minimum •Maximum •Average

* The measurement taken when the HOLD button was pressed.

Automatic Power-Off

The ANM-50 shuts off after approximately 20 minutes of inactivity to conserve

battery power. To bypass this feature, turn the unit off and follow this sequence:

1. Press and hold the HOLD button.

2. Press the ON-OFF RESET button and release.

A lowercase letter “n”will appear on the display.

Advanced Functions

Air Velocity Average (Multiple Locations)

1. If the unit is on, press and hold the AVERAGE MULTI-POINT button until the

unit beeps twice to erase any stored data.

Turn the unit on. When “vel”appears in the upper left corner and the

temperature appears in the lower right corner, the unit is ready to take a

measurement.

2. Place the unit in the airstream.

3. After taking the measurement, press and release the HOLD button.

You will hear a tone and HOLD will appear on the display.

4. Press the MIN/MAX REC button.

You will hear a tone and a single digit (1 –8) will appear on the display.

This digit is the location number.

5. Repeat Steps 2 –5 until all of the locations have been tested, up to the

maximum of 8 points.

6. Press the AVERAGE MULTI-POINT button.

The display will show the average air velocity measurement and the number

of locations tested.

Air Flow Measurement (Single Location)

Air flow, or volume of air per unit of time, is calculated by multiplying the air

velocity by the free area of the grill or register. This specification is available from

the grill or register manufacturer.

1. Turn the unit on.

2. Press the MODE VELOCITY FREE AREA FLOW button.

AREA and 1.111 will appear on the display.

The leftmost digit will flash.

If this is correct for your application, proceed to Step 3.

Otherwise change the area value as shown below.

•Press the HOLD button to increment the flashing digit.

•Press the AVERAGE MULTI-POINT button to advance to the next digit.

Press the MODE VELOCITY FREE AREA FLOW button to save the information.

FLOW will appear on the display.

4. Place the unit in the airstream.

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Messgerät Handbücher

Greenlee

Greenlee FC-110 Bedienungsanleitung

Greenlee

Greenlee 5124 Bedienungsanleitung

Greenlee

Greenlee 93-172 Bedienungsanleitung

Greenlee

Greenlee AirScout Gigacheck Bedienungsanleitung

Greenlee

Greenlee 5778 Leitfaden

Greenlee

Greenlee IPM-400 Bedienungsanleitung

Greenlee

Greenlee CM-660 Bedienungsanleitung

Greenlee

Greenlee 5990A Bedienungsanleitung

Greenlee

Greenlee BLL-200 Bedienungsanleitung

Greenlee

Greenlee CMT-90 Bedienungsanleitung

Greenlee

Greenlee 93-20 Bedienungsanleitung

Greenlee

Greenlee DataScout 10G Bedienungsanleitung

Greenlee

Greenlee CMF-110 Bedienungsanleitung

Greenlee

Greenlee GOPM Micro-01 Bedienungsanleitung

Greenlee

Greenlee 560XL Bedienungsanleitung

Greenlee

Greenlee CMF-110 Bedienungsanleitung

Greenlee

Greenlee 500XP Bedienungsanleitung

Greenlee

Greenlee CM-600 Bedienungsanleitung

Greenlee

Greenlee Pull Connect Bedienungsanleitung

Greenlee

Greenlee IPM-300 Bedienungsanleitung

Greenlee

Greenlee 180XL Bedienungsanleitung

Greenlee

Greenlee AM-600T Bedienungsanleitung

Greenlee

Greenlee SML-200 Bedienungsanleitung

Greenlee

Greenlee CM-1360 Bedienungsanleitung

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

Keysight

Keysight M8290A Bedienungsanleitung

Acterna

Acterna MS1400 Bedienungsanleitung

R&S

R&S ZPH Bedienungsanleitung

Datacolor

Datacolor ColorReader DC10-2 Bedienungsanleitung