Greenlee CM-600 Bedienungsanleitung

CM-600

Clamp-on Meter

Medidor con pinza

Contrôleur à pince

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and safety

information in this manual before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre

seguridad que aparecen en este manual, antes de manejar estas

herramientas o darles mantenimiento.

Lire attentivement et bien comprendre toutes les instructions et

les informations sur la sécurité de ce manuel avant d‘utiliser ou de

procéder à l‘entretien de cet outil.

Description

The Greenlee CM-600 Clamp-on Meter is a hand-held testing device with the following

measurement capabilities: AC and DC voltage, AC current, and resistance. It also verifies

continuity and has data hold capability.

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This instruction

manual and any markings on the tool provide information for avoiding hazards and unsafe

practices related to the use of this tool. Observe all of the safety information provided.

Purpose of This Manual

This instruction manual is intended to familiarize all personnel with the safe operation and

maintenance procedures for the Greenlee CM-600 Clamp-on Meter.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

KEEP THIS MANUAL

All specifications are nominal and may change as design improvements occur.

Greenlee Textron shall not be liable for damages resulting from misapplication or misuse of its products.

® Registered: The color green for electrical test instruments is a registered trademark of Greenlee Textron.

CM-600

Important Safety Information

This symbol is used to call your attention to hazards or unsafe practices which could

result in an injury or property damage. The signal word, defined below, indicates the

severity of the hazard. The message after the signal word provides information for

preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or property

damage.

Read and understand this material before operating or servicing this

equipment. Failure to understand how to safely operate this tool

could result in an accident causing serious injury or death.

Important Safety Information

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Do not use the unit if it is wet or damaged.

• Use test leads or accessories that are appropriate for the application. Refer to the

category and voltage rating of the test lead or accessory.

• Inspect the test leads or accessory before use. They must be clean and dry, and the

insulation must be in good condition.

• Use this unit for the manufacturer’s intended purpose only, as described in this

manual. Any other use can impair the protection provided by the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or between

any input terminal and earth ground.

• Do not contact the test lead tips or any uninsulated portion of the accessory.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

CM-600

Important Safety Information

Electric shock hazard:

• Do not operate with the case or battery cover open.

• Before removing the case or battery cover, remove the test leads (or jaw) from the

circuit and shut off the unit.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

Do not change the measurement function while the test leads are connected to a

component or circuit.

Failure to observe this precaution may result in injury and can damage the unit.

Electric shock hazard:

• Unless measuring voltage or current, shut off and lock out power. Make sure that all

capacitors are discharged. Voltage must not be present.

• Using this unit near equipment that generates electromagnetic interference can

result in unstable or inaccurate readings.

Failure to observe these warnings could result in severe injury or death.

Electric shock hazard:

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

Refer to “Specifications.”

Failure to observe these precautions may result in injury and can damage the unit.

Identification

1. Display

2. Selector

3. Lever

4. Jaw

5. HOLD button

6. Common (COM)

input terminal

7. Volts or resistance

(V-Ω) input

terminal

8. Battery cover

9. Battery cover

screw

Symbols on the Unit

Warning—Read the instruction manual

Double insulation

Battery

Front Back

Display Icons

10. –Polarity indicator

11. Hold function is enabled

12. Low battery indicator

13. Overload indication

CM-600

1. Set the selector according to the Settings Table.

2. Refer to “Typical Measurements”for specific measurement instructions.

3. Test the unit on a known functioning circuit or component.

•If the unit does not function as expected on a known functioning circuit, replace the

battery.

•If the unit still does not function as expected, send the unit to Greenlee for repair. Refer to

the instructions under the Warranty.

4. Take the reading from the circuit or component to be tested.

5. Press HOLD to hold the measured value on the display.

Settings Table

Electric shock hazard:

Contact with live circuits could result in severe injury or death.

Operation

To measure set the selector connect the and connect the

this value … to this symbol … red lead to … black lead to …

DC Voltage V-ΩCOM

AC Voltage V-ΩCOM

AC Current N/A N/A

(200 A max.)

AC Current N/A N/A

(200 A to 600 A)

Continuity V-ΩCOM

Resistance* V-ΩCOM

*Tone indicates circuit resistance is less than 50 Ω.

Auto Power Off

When the meter is powered on, a timer is activated that will turn the unit off after approximately

30 minutes. To continue making measurements after the unit automatically powers off, switch

the selector to OFF and then back to the desired function.

Typical Measurements

Current Measurement—

Clamp Around Wire

Notes:

•Clamp the jaw around one conductor

only.

•Close the jaw completely to ensure

accurate measurement.

•Center the wire in the jaw for highest

accuracy.

Voltage Measurement

CM-600

Typical Measurements

Current Measurement—

Clamp Around Line Splitter

Notes:

•The Greenlee 93-30 Line Splitter is divided.

One section renders amps; the other renders

amps multiplied by 10.

•Close the jaw completely to ensure accurate

measurement.

•Center the line splitter in the jaw for highest

accuracy.

Resistance Measurement

Typical Measurements

Continuity Check

Andere Handbücher für CM-600

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Multimeter Handbücher

Greenlee

Greenlee 93-603 Benutzerhandbuch

Greenlee

Greenlee GRDM-45 Bedienungsanleitung

Greenlee

Greenlee DM-300 Bedienungsanleitung

Greenlee

Greenlee DM-200A Bedienungsanleitung

Greenlee

Greenlee CMI-100 Bedienungsanleitung

Greenlee

Greenlee DM-50 Bedienungsanleitung

Greenlee

Greenlee DM-830A Bedienungsanleitung

Greenlee

Greenlee CM-850 Bedienungsanleitung

Greenlee

Greenlee CMI-200 Bedienungsanleitung

Greenlee

Greenlee 93-105 Bedienungsanleitung

Greenlee

Greenlee CM-600 Bedienungsanleitung

Greenlee

Greenlee DM-800 Bedienungsanleitung

Greenlee

Greenlee DM-860 Bedienungsanleitung

Greenlee

Greenlee DM-45 Bedienungsanleitung

Greenlee

Greenlee DM-860 Bedienungsanleitung

Greenlee

Greenlee CM-330 Bedienungsanleitung

Greenlee

Greenlee CM-900 Bedienungsanleitung

Greenlee

Greenlee CMP-200 Bedienungsanleitung

Greenlee

Greenlee DM-860A Bedienungsanleitung

Greenlee

Greenlee DM-200 Bedienungsanleitung

Greenlee

Greenlee DM-810A Bedienungsanleitung

Greenlee

Greenlee DM-500 Bedienungsanleitung

Greenlee

Greenlee DM-200 Bedienungsanleitung

Greenlee

Greenlee CM-1500 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung