Greenlee DM-800 Bedienungsanleitung

DM-800 • DM-810

• DM-820

DIGITAL

MULTIMETERS

MULTÍMETROS

DIGITALES

MULTIMETRES

NUMERIQUES

INSTRUCTION MANUAL

MANUAL DE INSTRUCCIONES

MANUEL D’INSTRUCTIONS

Read and understand all of the instructions and safety

information in this manual before operating or servicing this tool.

Lea y entienda todas las instrucciones y la información sobre

seguridad que aparecen en este manual, antes de manejar estas

herramientas o darles mantenimiento.

Lire attentivement et bien comprendre toutes les instructions et

les informations sur la sécurité de ce manuel avant d’utiliser ou de

procéder à l’entretien de cet outil.

Description

The Greenlee DM-800, DM-810 and DM-820 Digital Multimeters are hand-held testing devices

with the following measurement capabilities: AC and DC voltage, AC and DC current,

temperature (K-type thermocouples only), frequency, resistance and capacitance. They also

check diodes and verify continuity.

Specialized functions and capabilities include:

• MAX/MIN function, which stores the maximum, minimum, and difference

(maximum – minimum)

• Bar graph display, which responds more quickly than the numeric display —␣ useful for

detecting faulty contacts, potentiometer clicks and signal spikes

• Crest capture mode to capture voltage or current signal peaks

• Zoom mode analog pointer, which magnifies the bar graph for higher resolution

Safety

Safety is essential in the use and maintenance of Greenlee tools and equipment. This

instruction manual and any markings on the tool provide information for avoiding hazards and

unsafe practices related to the use of this tool. Observe all of the safety information provided.

Purpose

This instruction manual is intended to familiarize all personnel with the safe operation and

maintenance procedures for the Greenlee DM-800, DM-810 and DM-820 Digital Multimeters.

Keep this manual available to all personnel.

Replacement manuals are available upon request at no charge.

and are registered trademarks of Greenlee Textron.

KEEP THIS MANUAL

DM-800 • DM-810 • DM-820

Important Safety Information

This symbol is used to call your attention to hazards or unsafe practices which could

result in an injury or property damage. The signal word, defined below, indicates the

severity of the hazard. The message after the signal word provides information for

preventing or avoiding the hazard.

SAFETY ALERT SYMBOL

Immediate hazards which, if not avoided, WILL result in severe injury or death.

Hazards which, if not avoided, COULD result in severe injury or death.

Hazards or unsafe practices which, if not avoided, MAY result in injury or property

damage.

Read and understand this material before operating or servicing

this equipment. Failure to understand how to safely operate this

tool can result in an accident causing serious injury or death.

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

Important Safety Information

Electric shock hazard:

• Do not use the unit if it is wet or damaged.

• Use test leads or accessories that are appropriate for the application. See the

category and voltage rating of the test lead or accessory.

• Inspect the test leads or accessory before use. The item(s) must be clean and dry,

and the insulation must be in good condition.

Failure to observe these warnings can result in severe injury or death.

Electric shock hazard:

• Do not apply more than the rated voltage between any two input terminals, or

between any input terminal and earth ground.

• Do not contact the test lead tips or any uninsulated portion of the accessory.

Failure to observe these warnings can result in severe injury or death.

• Do not operate with the case open.

• Before opening the case, remove the test leads from the circuit and shut off the unit.

Failure to observe these warnings can result in severe injury or death.

Electric shock and fire hazard:

• Do not expose this unit to rain or moisture.

• Use this unit for the manufacturer’s intended purpose only, as described in this

manual. Any other use can impair the protection provided by the unit.

Failure to observe these warnings can result in severe injury or death.

DM-800 • DM-810 • DM-820

Important Safety Information

Do not change the measurement function while the test leads are connected to a

component or circuit.

Failure to observe this precaution can result in injury and can damage the unit.

• Do not attempt to repair this unit. It contains no user-serviceable parts.

• Do not expose the unit to extremes in temperature or high humidity.

See Specifications.

Failure to observe these precautions can result in injury and can damage the unit.

Unless measuring voltage, current or frequency, shut off and lock out power. Make

sure that all capacitors are discharged. Voltage must not be present.

The fuse is an integral part of the overvoltage protection. When fuse replacement is

necessary, see Specifications for the correct type, size and capacity. Using any other

type of fuse will void the overvoltage protection rating of the unit.

Failure to observe this warning can result in severe injury or death.

Set the selector and connect the test leads so that they correspond to the intended

measurement. Incorrect settings or connections can result in a blown fuse.

Using this unit near equipment that generates electromagnetic interference can result

in unstable or inaccurate readings.

Identification

1. Display LCD and bar graph

2. Feature Buttons See explanations under Using the Features

3. Selector Selects a function or turns power OFF

4. APositive input terminal for high current measurements

5. mA µAPositive input terminal for low current measurements

6. COM Negative, common or ground input terminal for all measurements

7. ΩVPositive input terminal for all measurements

except

current

DM-800 • DM-810 • DM-820

Display Icons

8. Automatic Ranging is enabled.

9. Hold function is enabled.

10. Crest Capture function is enabled.

11. DC measurement is selected.

12. AC measurement is selected.

13. – Polarity Indicator

14. Diode

15. Low Battery

16. ∆Relative Zero function is enabled.

17. Bar graph is magnified for higher

resolution.

18. – Polarity for Bar Graph

19. OL Overload (numeric display)

Overload (bar graph display)

20. Bar Graph Element

21. MAX MIN MAX/MIN mode is enabled.

9–10

11–12

15–16

26–28

29–32

23–25

19 20

22. Continuity

23. n Nano (10-9)

24. µMicro (10-6)

25. F Farads

26. m Milli (10-3)

27. V Volts

28. A Amps

29. M Mega (106)

30. k Kilo (103)

31. ΩOhms

32. Hz Hertz (frequency in

cycles per second)

33. (variable) Sensitivity level for

Hz feature

Using the Features

• Automatic Power Off To extend battery life, the meter will shut itself off after approximately

17 minutes of inactivity. To restore power, press any button. To disable this feature, press

RANGE while turning the meter on.

• MAX/MIN (DM-820 only) Press momentarily to begin recording the input. MAX MIN will

appear on the display. The meter will beep whenever the minimum or maximum is updated.

When using the MAX/MIN function, press momentarily to cycle through the maximum,

minimum, difference (MAX – MIN). Press and hold to exit this mode.

The Automatic Power Off feature is disabled when using this function.

• CREST (DM-820 only) Press momentarily to capture the crests of AC or DC voltage or

current. and MAX will appear on the display. The meter will capture and hold a signal

peak with a duration as short as 5 ms. Press momentarily to cycle through the maximum

crest, minimum crest and maximum – minimum crest (peak to peak). Press and hold to exit

this mode.

The Automatic Power Off feature is disabled when using this function.

•∆(DM-820 only) Finds the difference between two measurements. While taking a

measurement, press ∆to set the display to zero. The ∆icon will appear on the display. Take

the second measurement. The value on the display will be the difference between the two

measurements. Press again to exit this mode.

•(DM-820 only) Press momentarily to change the resolution of the bar graph.

•Press and hold until LCD illuminates. The lamp turns off after 30 seconds to extend

battery life.

• SELECT Press momentarily to toggle between functions, or to toggle between AC and DC

when measuring current and millivolts.

• RANGE Press once to enter the manual ranging mode. The icon will disappear from

the display. Press repeatedly to step through the ranges. Press and hold to return to the

automatic ranging mode.

Note: When using MAX/MIN, HOLD, or

∆

mode, pressing

RANGE

will cause the meter to

exit that mode.

•HzPress to measure frequency.

Note: The sensitivity of the frequency measurement function varies with the measurement

range. To automatically select a sensitivity level, measure the voltage level first, then press

. If the reading becomes unstable, or if the display is blank, manually change the

sensitivity by momentarily pressing

RANGE.

• HOLD Press momentarily to hold the present value on the display. Press again to exit

this mode.

This feature does not affect the bar graph.

DM-800 • DM-810 • DM-820

*The crest factor is the ratio of the peak value to the RMS value; it is represented by the

Greek letter ξ.

mrofevaW

eulaVSMR 001001001001

eulaVdeifitceR 090017846

*rotcaFtserC

(ξ)

414.1137.12

AC Measurement

AC measurements are usually displayed as RMS

(root mean squared)

values. Two methods of

AC measurement are

average-responding RMS calibrated

and

true RMS-reading

The average-responding RMS calibrated method takes the average value of the input signal,

multiplies it by 1.11, and displays the result. This method is accurate if the input signal is a

pure sine wave. The Greenlee DM-800 is an average-responding meter.

The true RMS-reading method uses internal circuitry to read the true RMS value. This method

is accurate, within the specified crest factor limitations, whether the input signal is a pure sine

wave, a square wave, sawtooth wave, half wave or signal with harmonics. The ability to read

true

RMS provides much more measurement versatility. The Greenlee DM-810 and DM-820 are

true RMS meters.

The Waveforms and Crest Factors table shows some typical AC signals and their RMS values.

Waveforms and Crest Factors

Operation

Electric shock hazard:

Contact with live circuits can result in severe injury or death.

1. See the Settings Table. Set the selector to the proper setting, press SELECT (when

instructed to do so), and connect the test leads to the meter.

2. See Typical Measurements for specific measurement instructions.

3. Test the unit on a known functioning circuit or component.

• If the unit does not function as expected on a known functioning circuit, replace the

battery and/or fuses.

• If the unit still does not function as expected, send the unit to Greenlee for repair.

4. Take the reading from the circuit or component to be tested.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Greenlee Multimeter Handbücher

Greenlee

Greenlee 93-105 Bedienungsanleitung

Greenlee

Greenlee DM-860A Bedienungsanleitung

Greenlee

Greenlee DM-300 Bedienungsanleitung

Greenlee

Greenlee CM-600 Bedienungsanleitung

Greenlee

Greenlee DM-40 Bedienungsanleitung

Greenlee

Greenlee CM-600 Bedienungsanleitung

Greenlee

Greenlee CM-900 Bedienungsanleitung

Greenlee

Greenlee 93-500 Bedienungsanleitung

Greenlee

Greenlee DM-50 Bedienungsanleitung

Greenlee

Greenlee DM-860 Bedienungsanleitung

Greenlee

Greenlee CM-330 Bedienungsanleitung

Greenlee

Greenlee CM-1050 Bedienungsanleitung

Greenlee

Greenlee PDMM-20 Bedienungsanleitung

Greenlee

Greenlee 93-603 Benutzerhandbuch

Greenlee

Greenlee 93-602 Bedienungsanleitung

Greenlee

Greenlee DM-25 Bedienungsanleitung

Greenlee

Greenlee DM-20 Bedienungsanleitung

Greenlee

Greenlee 93-604 Bedienungsanleitung

Greenlee

Greenlee DM-200 Bedienungsanleitung

Greenlee

Greenlee CM-1300 Bedienungsanleitung

Greenlee

Greenlee CM-1200 Bedienungsanleitung

Greenlee

Greenlee DM-45 Bedienungsanleitung

Greenlee

Greenlee CM-400 Bedienungsanleitung

Greenlee

Greenlee CMP-200 Bedienungsanleitung

Beliebte Multimeter Handbücher anderer Marken

Agilent Technologies

Agilent Technologies 34420A Bedienungsanleitung

Fluke

Fluke 83 Bedienungsanleitung

Hameg

Hameg HM 8012 Bedienungsanleitung

Mastech

Mastech MY70 Bedienungsanleitung

Steren

Steren MUL-300 Bedienungsanleitung

Somogyi Elektronic

Somogyi Elektronic home SMA 92 Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRAmax 6 Bedienungsanleitung

PeakTech

PeakTech 4000 Gebrauchs- und Pflegehandbuch

YOKOGAWA

YOKOGAWA 90050B Bedienungsanleitung

Gossen MetraWatt

Gossen MetraWatt METRALINE DMM16 Bedienungsanleitung

Fluke

Fluke 8846A Bedienungs- und Wartungshandbuch

Tempo Communications

Tempo Communications MM200 Bedienungsanleitung

Elenco Electronics

Elenco Electronics CM-1555 Bedienungsanleitung

Mastech

Mastech MS8238C Bedienungsanleitung

SDAR

SDAR 830A, 830B, 830D, 830C Bedienungsanleitung

RS PRO

RS PRO RS-9519BT Bedienungsanleitung

BGS technic

BGS technic 8890 Bedienungsanleitung

Amprobe

Amprobe Hexagon 60 Bedienungsanleitung