Grizzly T10812 Bedienungsanleitung

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T10812

CARVING VISE

INSTRUCTIONS

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#BB16757 PRINTED IN CHINA

Introduction

The Model T10812 Carving Vise mounts to a

workbench to securely hold a carving project

while providing highly adjustable positioning. This

product comes fully assembled and ready to use.

Description Qty

A. Carving Vise ............................................... 1

B. Pin Wrench ................................................. 1

Inventory

Figure 1. T10812 carving vise.

Specifications

Height ...............................................................8"

Width ................................................................7"

Base ....................................................... 51⁄4" dia.

Weight .......................................................14 lbs.

Carving Faceplate ..................................... 5" dia.

Faceplate Mounting Holes ............................... 16

Range of Motion (Rotation) ..........................360°

Construction ......................... Cast Iron and Steel

Your vise was carefully packaged for safe trans-

portation. Remove the packaging materials from

around your vise and inspect it. If you discover

any damage, please call us immediately at (570)

546-9663 for advice.

Save the containers and all packing materials for

possible inspection by the carrier or its agent.

Otherwise, filing a claim can be difficult.

When you are completely satisfied with the condi-

tion of your shipment, inventory the contents.

The following is a list of items shipped with your

vise. Before beginning setup, lay these items out

and inventory them.

If any non-proprietary parts are missing (e.g. a

nut or a washer), we will gladly replace them; or

for the sake of expediency, replacements can be

obtained at your local hardware store.

-2- T10812 Carving Vise (Mfd. 09/14)

Figure 4. T10812 part identification.

Retaining

Collar

Clamping

Handle

Clamping

Assembly

Faceplate/Column

Assembly

Attaching Workpiece

The Carving Vise faceplate has 16 mounting holes

to accommodate a variety of workpieces. When

attaching a workpiece, use a minimum of four but-

ton head screws. Make sure the screws are long

enough to provide a safe, stable work surface, but

will not interfere with carving activities.

Avoid placing hands close to pinch points

located at clamping assembly and retaining

collar. Serious injury may occur.

Carving Vise

Workbench

Hex

Bolt

Flat Washer

Lock Washer

Hex Nut

Carving Vise

Workbench

Lag Screw

Flat Washer

Another option is a "Direct Mount" (see example

below) where the vise is secured directly to the

workbench with lag screws and washers.

The base of this vise has mounting holes that allow

it to be fastened to a workbench or other mounting

surface to prevent it from moving during operation

and causing accidental injury or damage.

The strongest mounting option is a "Through

Mount" where holes are drilled all the way through

the workbench—and hex bolts, washers, and hex

nuts are used to secure the vise in place.

Bench Mounting

Mount the carving vise on a workbench that is

sturdy enough to hold the weight of the equipment

and any downward pressure that may be applied

during operation.

When mounting your carving vise, remember to

allow enough room so workpiece position can be

fully adjusted, and to place carving vise in a well

lit area.

Installation

Damage to your eyes, lungs, and ears could

result from using this item without proper

protective gear, such as safety glasses, a

respirator, and hearing protection.

Refer to Figure 4 to become familiar with the

names and locations of the controls and features.

Figure 2. Typical "Through Mount" setup.

Figure 3. Typical "Direct Mount" setup.

T10812 Carving Vise (Mfd. 09/14) -3-

To attach workpiece to faceplate:

1. While holding faceplate, loosen clamping

handle (see Figure 4).

2. Remove faceplate/column assembly from

clamping assembly.

3. Locate appropriate position for workpiece on

faceplate.

4. Select at least four mounting holes and mark

through faceplate onto workpiece with sharp

pencil.

Note: Mounting points should be placed

evenly across workpiece to avoid stress that

could cause screws to break.

5. Pre-drill holes in workpiece slightly smaller in

diameter than mounting screws.

6. Position faceplate on workpiece and attach

with button head wood screws.

1. While holding faceplate, loosen clamping

handle (see Figure 4).

2. Position workpiece.

3. Tighten clamping handle.

Adjusting Tilt and Height

Adjusting Rotation

1. Insert pin wrench into retaining collar (see

Figure 6).

2. Turn retaining collar counterclockwise until

the vise rotates freely.

3. Position workpiece.

4. Turn retaining collar clockwise until snug.

5. Remove pin wrench and store in safe place.

Figure 6. Insert pin wrench.

Wrench

Retaining

Collar

7. With workpiece securely attached to face-

plate, re-install faceplate/column assembly

into clamping assembly.

8. Tighten clamping handle.

Note: When carving small, narrow, or oddly

shaped workpieces, it may be necessary

to attach an intermediate base to faceplate

providing a larger, more stable work area for

workpiece.

Figure 5. Correct screw type for faceplate

attachment.

Correct Incorrect

DO NOT use screws with tapered heads

to attach the faceplate because they could

split the faceplate, or the screws could snap

off during operation. See the illustration in

Figure 5 for examples.

-4- T10812 Carving Vise (Mfd. 09/14)

234

T10812 Parts Breakdown

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT10812001 VISE BODY 8 PT10812008 ROLL PIN 6 X 30

2 PT10812002 LOCKING HANDLE 9 PT10812009 PIN WRENCH

3 PT10812003 FENDER WASHER 12MM 10 PT10812010 RETAINING COLLAR

4 PT10812004 CLAMPING INSERT M12-1.75 X 40 11 PT10812011 VISE BASE

5 PT10812005 CLAMPING SLEEVE 12 PT10812012 VISE BASE PLATE

6 PT10812006 COLUMN 13 PT10812013 PIN 6 X 20MM

7 PT10812007 FACEPLATE

Andere Grizzly Werkzeuge Handbücher

Grizzly

Grizzly 7 1/2" Mini Shear Brake T21322 Bedienungsanleitung

Grizzly

Grizzly T23103 Bedienungsanleitung

Grizzly

Grizzly H6087 Bedienungsanleitung

Grizzly

Grizzly H7585 Bedienungsanleitung

Grizzly

Grizzly T28929 Bedienungsanleitung

Grizzly

Grizzly H3142 Kurzanleitung

Grizzly

Grizzly T25101 Bedienungsanleitung

Grizzly

Grizzly G4181 Bedienungsanleitung

Grizzly

Grizzly H7507 Bedienungsanleitung

Grizzly

Grizzly G8748 Bedienungsanleitung

Grizzly

Grizzly T1227 Bedienungsanleitung

Grizzly

Grizzly H3142 Bedienungsanleitung

Grizzly

Grizzly T32796 Bedienungsanleitung

Grizzly

Grizzly H0613 Bedienungsanleitung

Grizzly

Grizzly G1870 Bedienungsanleitung

Grizzly

Grizzly T23034 Bedienungsanleitung

Grizzly

Grizzly H7583 Bedienungsanleitung

Grizzly

Grizzly T26857 Bedienungsanleitung

Grizzly

Grizzly T31566 Bedienungsanleitung

Grizzly

Grizzly T32838 Bedienungsanleitung

Grizzly

Grizzly G0497 Bedienungsanleitung

Grizzly

Grizzly G0711 Bedienungsanleitung

Grizzly

Grizzly T23124 Bedienungsanleitung

Grizzly

Grizzly H6472 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung