Grizzly T32838 Bedienungsanleitung

Introduction

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 11/21) #CS22151 PRINTED IN TAIWAN V1.11.21

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

MODEL T32838

BANDSAW SLED

INSTRUCTIONS

Figure 1. Example of Model T32838 installed on

bandsaw.

Inventory

Description (Figure 2) Qty

A. Sled Assembly ............................................ 1

B. Rear Rail Mounting Brackets ...................... 2

C. Front Rail Mounting Brackets ..................... 2

D. Hex Wrenches 3, 4mm .........................1 Ea.

E. Hex Bolts M6-1 x 16 ................................... 4

F. Hex Bolts 1⁄4"-20 x 5⁄8" ................................. 4

G. Flat Washers 1⁄4" ......................................... 4

H. Square Nuts 5⁄16"-18 .................................... 4

I. Open-End Wrench 10mm ........................... 1

J. Rear Rail .................................................... 1

K. Scale .......................................................... 1

L. Front Rail .................................................... 1

M. Pointer ........................................................ 1

N. Button Head Cap Screws M5-.8 x 10 ......... 2

O. Knob Bolts 5⁄16"-18 x 5⁄8" .............................. 4

Figure 2. T32838 inventory.

NOTICE

If you cannot find item on list, check around/

inside packaging materials. Often, items

get lost in packaging while unpacking or

they are pre-installed at factory.

The Model T32838 Bandsaw Sled (see Figure 1)

fits vertical wood-cutting bandsaws with tables

between 127⁄8"–181⁄2" long, and allows you to pro-

cess logs when used with one of the accessories

listed on Page 5.

-2- Model T32838 (Mfd. Since 11/21)

Assembly

The existing rails on your bandsaw must be

removed to install the Model T32838.

Wear safety glasses during

the entire setup process!

To assemble bandsaw sled:

1. DISCONNECT BANDSAW FROM POWER!

2. Remove existing rails on your bandsaw.

3. Install (2) front rail mounting brackets to front

of bandsaw table (see Figure 3) using hard-

ware removed in Step 2. Only finger-tighten

for now.

Note: T32838 comes with (4) M6-1 x 16 hex

bolts, (4) 1⁄4"-20 x 5⁄8" hex bolts, and (4) 1⁄4"

flat washers. These can be used instead of

hardware from Step 2 if they fit your machine.

Figure 3. Example of front rail mounting

brackets installed on bandsaw table.

4. Install (2) rear rail mounting brackets to

rear of bandsaw table (see Figure 4) using

hardware removed in Step 2 (or hardware

included with T32838). Only finger-tighten for

now.

Figure 4. Example of rear rail mounting brackets

installed on bandsaw table.

Rear Rail

Mounting Bracket

(1 of 2)

Bandsaw Table

5. Loosely install (2) 5⁄16"-18 x 5⁄8" knob bolts

and 5⁄16"-18 square nuts on front rail mounting

brackets, as shown in Figure 5.

Front Rail

Mounting Bracket

(1 of 2)

Bandsaw

Table

Figure 5. Knob bolts and square nuts installed

on front rail mounting brackets.

x 2

Front Rail

Mounting Bracket

(1 of 2)

Items Needed Qty

Vertical Wood-Cutting Bandsaw ....................... 1

Tools to Remove Bandsaw Rails ....... As Needed

Safety Glasses (For Each Person) ...............1 Pr.

Wrench or Socket 8mm ..................................... 1

Model T32838 (Mfd. Since 11/21) -3-

6. Slide square nuts into T-slot on bottom of

front rail, as shown in Figure 6, then tighten

knobs to secure rail position.

Note: To allow for longer workpieces, adjust

rail as far right as possible where it can still

be secured by left knob.

Figure 6. Installing front rail.

7. Repeat Steps 5–6 with rear rail, aligning rear

rail edges to front rail edges.

8. Lift sled handle and place sled assembly on

rails and bandsaw table (see Figure 7).

Figure 7. Sled placed on front and rear rails.

Front Rail

Sled Handle

Rear Rail

T-Slot

Figure 8. Location of bumper fasteners.

9. Loosen or remove (2) cap screws, fender

washers, and hex nuts shown in Figure 8

to adjust or re-install bumpers so they are

directly above rear rail.

x 2

Bumper

(1 of 2)

Note: If you cannot install bumpers directly

above rear rail, you can also adjust place-

ment of fasteners shown in Figure 9 so sled

better fits your bandsaw table.

x 4

Figure 9. Location of sled frame position

fasteners.

10. Adjust rails up or down as needed so sled

is slightly above table, then tighten fasten-

ers from Steps 3–4. Bumpers should con-

tact rear rail and sled should slide smoothly

across rails and table.

Note: You may need to position rear rail out

of the way in order to access fasteners.

-4- Model T32838 (Mfd. Since 11/21)

12. Adjust sled on rails until edge of sled is flush

against bandsaw blade (see Figure 11), then

move sled handle down to lock position on

rails.

13. Mark location of pointer on front rail (see

Figure 12).

Figure 12. Pointer location marked on rail where

sled contacts blade.

Note: If you adjust rail position, scale will

no longer be accurate. If you think you may

adjust rails, affix scale with tape for now.

16. Lift sled handle and install bandsaw sled on

rails.

17. Refer to Model T32839, Model T32840, or

Model T32841 instructions to install accesso-

ries for crosscut, miter, or milling operations.

Figure 11. Sled edge flush and locked in

position against blade.

Sled

Handle

Blade

14. Lift sled handle to unlock position, then

remove bandsaw sled from rails.

15. Remove sticker-back from scale and adhere

scale to front rail, aligning 0" on scale with

mark from Step 13 (see Figure 13).

Mark

Figure 13. Scale attached to front rail.

Mark

0" on Scale

Figure 10. Pointer attached to sled.

x 2

Pointer

11. Attach pointer to sled with (2) M5-.8 x 10 but-

ton head cap screws (see Figure 10).

Model T32838 (Mfd. Since 11/21) -5-

order online at www.grizzly.com or call 1-800-523-4777

Accessories

Installing unapproved accessories may

cause machine to malfunction, resulting in

serious personal injury or machine damage.

To reduce this risk, only install accessories

recommended for this machine by Grizzly.

NOTICE

Refer to our website or latest catalog for

additional recommended accessories.

T32839—Sliding Log Crosscut Jig

The Model T32839 Sliding Log Crosscut Jig

attaches to the T32838 Bandsaw Sled to per-

form crosscut operations on vertical wood-cutting

bandsaws.

Figure 14. T32839 Sliding Log Crosscut Jig for

T32838.

T32840—Sliding Log Miter Table

The T32840 Sliding Log Miter Table attaches to

the T32838 Bandsaw Sled to perform miter cut

operations on vertical wood-cutting bandsaws.

Figure 15. T32840 Sliding Log Miter Table for

T32838.

T32841—Sliding Log Milling Sled

The T32841 Sliding Log Milling Sled attaches

to the T32838 Bandsaw Sled to perform milling

operations on vertical wood-cutting bandsaws.

Figure 16. T32841 Sliding Log Milling Sled for

T32838.

-6- Model T32838 (Mfd. Since 11/21)

BUY PARTS ONLINE AT GRIZZLY.COM!

Scan QR code to visit our Parts Store.

T32838 Parts Breakdown & List

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here

are available for purchase. Call (800) 523-4777 or visit our online parts store at www.grizzly.com to check for availability.

23 27

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT32838001 BASE 17 PT32838017 LOCKING CAM

2 PT32838002 FLAT WASHER 5MM 18 PT32838018 PRESSURE PLATE

3 PT32838003 TRACK GUIDE PLATE 19 PT32838019 BEARI NG SHAFT (RIGHT)

4 PT32838004 TRACK 20 PT32838020 BEARING SHAFT (LEFT)

5 PT32838005 POINTER 21 PT32838021 BALL BEARING 6200ZZ

6 PT32838006 FRONT RAI L 22 PT32838022 EXT RETAI NI NG RI NG 10MM

7 PT32838007 BUMPER 23 PT32838023 SET SCREW 1/4-20 X 1/4

8 PT32838008 CAP SCREW M5-.8 X 16 24 PT32838024 FLAT WASHER 1/4

9 PT32838009 HEX NUT M5-. 8 25 PT32838025 HEX BOLT 1/4-20 X 5/8

10 PT32838010 REAR RAIL MOUNTI NG BRACKET 26 PT32838026 HEX NUT M8-1. 25

11 PT32838011 FRONT RAIL MOUNTING BRACKET 27 PT32838027 BUTTON HD CAP SCR M5-. 8 X 10

12 PT32838012 REAR RAI L 28 PT32838028 SCALE

13 PT32838013 KNOB BOLT 5/16-18 X 5/8, 12-LOBE, D1-1/2 29 PT32838029 HEX BOLT M6-1 X 16

14 PT32838014 SQUARE NUT 5/16-18 30 PT32838030 HEX WRENCH 3MM

15 PT32838015 HANDLE PIVOT PIN 31 PT32838031 HEX WRENCH 4MM

16 PT32838016 FIXED HANDLE 29 X 77, M8-1.25 X 40 32 PT32838032 WRENCH 10MM OPEN-END

WARRANTY & RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

In the event you need to use this warranty, contact us by mail or phone and give us all the details. We will

then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of

the carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

take advantage of this warranty, you must register it at https://www.grizzly.com/forms/warranty, or

you can

scan the QR code below to be automatically directed to our warranty registration page. Enter all

applicable information for

the product.

WARRANTY

Inhaltsverzeichnis

Andere Grizzly Werkzeuge Handbücher

Grizzly

Grizzly T10264 Bedienungsanleitung

Grizzly

Grizzly T28325 Bedienungsanleitung

Grizzly

Grizzly T32793 Bedienungsanleitung

Grizzly

Grizzly T25101 Bedienungsanleitung

Grizzly

Grizzly T32719 Bedienungsanleitung

Grizzly

Grizzly G0711 Bedienungsanleitung

Grizzly

Grizzly T31566 Bedienungsanleitung

Grizzly

Grizzly H0613 Bedienungsanleitung

Grizzly

Grizzly T28929 Bedienungsanleitung

Grizzly

Grizzly T10432 Bedienungsanleitung

Grizzly

Grizzly H3142 Kurzanleitung

Grizzly

Grizzly T10812 Bedienungsanleitung

Grizzly

Grizzly T32796 Bedienungsanleitung

Grizzly

Grizzly T10222 Bedienungsanleitung

Grizzly

Grizzly H3142 Bedienungsanleitung

Grizzly

Grizzly C1367 Bedienungsanleitung

Grizzly

Grizzly H7583 Bedienungsanleitung

Grizzly

Grizzly H6087 Bedienungsanleitung

Grizzly

Grizzly G0497 Bedienungsanleitung

Grizzly

Grizzly T1227 Bedienungsanleitung

Grizzly

Grizzly G1600 Bedienungsanleitung

Grizzly

Grizzly H8188 Bedienungsanleitung

Grizzly

Grizzly T32730 Bedienungsanleitung

Grizzly

Grizzly T23124 Bedienungsanleitung

Beliebte Werkzeuge Handbücher anderer Marken

Martor

Martor SECUNORM 175 Bedienungsanleitung

ERKCO

ERKCO 1000 Bedienungsanleitung

jbc

jbc N4473 Bedienungsanleitung

FEINMETALL

FEINMETALL FZWZ-SET-001 Bedienungsanleitung

Worx Professional

Worx Professional Sonicrafter WU676 Bedienungsanleitung

Gage Bilt

Gage Bilt GB713SH Bedienungsanleitung

Hilti

Hilti DX 9-ENP Bedienungsanleitung

norbar

norbar NORTRONIC 34399 Bedienungsanleitung

BGS technic

BGS technic 8578 Bedienungsanleitung

Makita

Makita DHR241 Bedienungsanleitung

Motor Guard

Motor Guard JMB-1250 Bedienungsanleitung

Power Adhesives

Power Adhesives 805-12 Bedienungsanleitung

Clemco

Clemco 24189 Bedienungsanleitung

VVG

VVG VNG 903 Series Bedienungsanleitung

Hilti

Hilti FX 3-A Bedienungsanleitung

axing

axing BWZ 5-02 Bedienungsanleitung

Dh-Robotics

Dh-Robotics RGI-100 Anleitung zur Verwendung

Goobay

Goobay 97790 Bedienungsanleitung