Grundfos MP 204 Bedienungsanleitung

Control MP 204

Installation and operating instructions

GRUNDFOS INSTRUCTIONS

Installation and operating instructions

http://net.grundfos.com/qr/i/99304312

Table of contents

Control MP 204

English (GB)

Installation and operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Deutsch (DE)

Montage- und Betriebsanleitung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Español (ES)

Instrucciones de instalación y funcionamiento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Français (FR)

Notice d'installation et de fonctionnement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Italiano (IT)

Istruzioni di installazione e funzionamento. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Polski (PL)

Instrukcja montażu i eksploatacji . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

ﺔﻳﺑﺭﻌﻟﺍ (AR)

ﻝﻳﻐﺷﺗﻟﺍ ﻭ ﺏﻳﻛﺭﺗﻟﺍ ﺕﺎﻣﻳﻠﻌﺗ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

English (GB)

English (GB) Installation and operating instructions

Original installation and operating instructions

These installation and operating instructions describe Grundfos

Control MP 204.

Sections 1-3 give the information necessary to be able to unpack,

install and start up the product in a safe way.

Sections 4-9 give important information about the product as well

as information on service, fault finding and disposal of the

product.

CONTENTS

Page

1. General information

1.1 Hazard statements

The symbols and hazard statements below may appear in

Grundfos installation and operating instructions, safety

instructions and service instructions.

The hazard statements are structured in the following way:

1.2 Notes

The symbols and notes below may appear in Grundfos

installation and operating instructions, safety instructions and

service instructions.

1. General information 4

1.1 Hazard statements 4

1.2 Notes 4

1.3 Scope of delivery 5

2. Installing the product 5

2.1 Mechanical installation 5

2.2 Electrical installation 5

3. Commissioning the product 8

3.1 Startup 8

3.2 Operation 8

4. Product introduction 8

4.1 Modules 8

4.2 Grundfos GO Remote 9

4.3 Communication 9

4.4 Identification 9

5. Control functions 10

5.1 Switch control 10

6. Taking the product out of operation 10

6.1 Decommissioning 10

7. Fault finding the product 11

8. Technical data 11

9. Disposal of the product 11

Read this document before installing the product.

Installation and operation must comply with local

regulations and accepted codes of good practice.

DANGER

Indicates a hazardous situation which, if not avoided,

will result in death or serious personal injury.

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious personal injury.

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate personal injury.

SIGNAL WORD

Description of hazard

Consequence of ignoring the warning.

- Action to avoid the hazard.

Observe these instructions for explosion-proof

products.

A blue or grey circle with a white graphical symbol

indicates that an action must be taken.

A red or grey circle with a diagonal bar, possibly with

a black graphical symbol, indicates that an action

must not be taken or must be stopped.

If these instructions are not observed, it may result in

malfunction or damage to the equipment.

Tips and advice that make the work easier.

English (GB)

1.3 Scope of delivery

These installation and operating instructions apply to the

Grundfos Control MP 204. The Control MP 204 is a control

cabinet with built-in motor protection.

These instructions only focus on the Control MP 204 control

cabinet.

The main component in the control cabinet is an MP 204 motor

protector. This component is not described in detail in this

manual.

Further documentation supplied with the Control MP 204:

• Technical documentation:

– wiring diagram

– parts list

– sectional drawing, etc.

• Installation and operating instructions for the MP 204.

For information on MP 204, see the installation and operating

instruction for the product.

Fig. 1 Example, Control MP 204

2. Installing the product

Before installation, check the following:

• Checkthat the specifications of the Control MP 204 correspond

to the order

• Check the product for transport damage.

Contact the transporter immediately in case of damage.

The Control MP 204 is operated either manually or via remote

access (optional). See section 3.2 Operation.

2.1 Mechanical installation

This section describes the mechanical installation of the Control

MP 204 and also provides general advice about how to position

sensors in order to achieve stable, measured values.

The control cabinet is designed for indoor use, either mounted on

a wall or directly on the floor.

2.1.1 Sensors

To ensure correct and reliable operation of the Control MP 204, it

is important to position and install sensors according to the

manufacturer's instructions.

2.1.2 Configuration of the product

Use Grundfos GO Remote to configure Control MP 204. See

4.2 Grundfos GO Remote.

2.2 Electrical installation

The electrical connection must be carried out by an authorised

electrician in accordance with local regulations.

The electrical installation must be carried out according to the

wiring diagram supplied with the Control MP 204.

Fig. 2 Example, Control MP 204, DOL version

The following sections are intended as a supplement to the wiring

diagram supplied with the Control MP 204.

The terminal blocks, X1, X10, X11, are shown in section

2.2.1 Terminal blocks.

TM07 1342 1318

If the product is to be used outdoors, it must be

located in a separate cabinet which is suitable for

outdoor use.

The sensors must always be correctly sized for the

range they are to measure. If the sensors are too

small, they will be saturated. If they are too big, the

resolution of the sensor signal will be too poor.

WARNING

Electric shock

Death or serious personal injury

Before starting any work on the product, make sure

that the power supply has been switched off and that

it cannot be accidentally switched on.

TM06 9435 2317

Pos. Description

1 MP 204 motor protector

2 Terminal block X0, main switch

3 Terminal blocks X1, X10, X11

4Circuit breakers

5 Contactor

6 Auxiliary relays

X0 Q00 X10 X11

F10

Q12 F01

E10

FE 5

T1 T2

L3/AL2/LL1/N K8 K10

Power Trip

R+

MP 204

ABY+CCSN 95969798

English (GB)

2.2.1 Terminal blocks

The cables and wires must be connected as shown in the wiring

diagram supplied with the Control MP 204.

Fig. 3 DOL example, terminals in control cabinet

Terminal block for mains supply, X0

Fig. 4 Terminal block for mains supply, X0

Terminal block for pump, X1, DOL

Fig. 5 Terminal block for pump, X1

The following connections must be made directly on the MP 204:

• T1-T2, PTC sensor or thermistor. They must be short-circuited

if no sensor or thermistor is connected.

• NO relay output, 2 A max., MP 204

• GENIbus A

• GENIbus Y

• GENIbus B

• +, Pt100 or Pt1000 sensor

• C, Pt100 or Pt1000 sensor

TM06 9438 2317TM06 9436 2317

Pos. Description

1N, PE

2L1

3L2

4L3

X0 Q00 X1 X10 X11

NUVWPE

1234 56

PE1 PE2 32 33 3 43 3 3765

1234

X0 Q00

NPE

TM06 9437 2617 - TM06 9450 2317

Connection Description

U Phase U

V Phase V

W Phase W

PE Ground connection

UVWPE

VWPEU

U1 V1 W1

M1 3~

English (GB)

Terminal block for pump alarm, X11

Fig. 6 Terminal block for pump alarm, X11

Terminal block for pressure switch or level switch, X10

Fig. 7 Terminal block for pressure switch or level switch, X10

TM06 9439 2317 - TM06 9636 2617

Connection Description

32-33 Pump run, 2 A

34-35 Fault, MP 204, 2 A

36-37 Fault, water shortage, 2 A

X11

32 33 343 3 3765

Q12

X11

K10

32 33 34 35 36 37

Pump run Fault, MP 204 Fault, water shortage

TM06 9440 2717

Connection Description

1-2 Ground connection

3-4 Pressure or level switch

PE1 Ground connection

5-6

Water-shortage supervision.

Pressure or level switch.

If not used, a cross-bridge is mounted.

PE2 Ground connection

All cables used for control signals from analog and

digital sensors must be screened to ensure stable

and correct function.

X10

1234 56

PE1 PE2

X10 1 2 3 4 PE1 5 6 PE2

B1 B2

PE PE

241PE

Minimum and

maximum pressure

switch

Example:

Water-shortage

pressure switch

Cross-bridge isolated

Water-shortage

supervision

Example:

Level switch

Cross-bridge

isolated

Remote On/Off

English (GB)

3. Commissioning the product

Checks before first startup:

• The pump is installed according to the installation and

operating instructions for the pump type used.

• The MP 204 is configured either by use of a PC Tool or with

Grundfos GO Remote according to the motor and pump

specifications.

3.1 Startup

The motor current and trip conditions have to be adjusted and set

during startup. To adjust and set these parameters, see

installation and operating instructions for the MP 204.

Check that the motor and pump operates according to the

specifications.

3.2 Operation

Control MP 204 is operated via a "H-O-A" switch in the cabinet

front or via a PC.

Manual, H

In Manual mode, the pump starts directly in DOL or SD mode.

Off, O

In Off mode, the pump is switched off.

Auto, A

In Auto mode, a pressure switch, float switch or a signal from a

PLC system, is used to control the pump.

For manual operation, both variants of the Control MP 204

incorporate the following components in the cabinet front.

Fig. 8 Example, Control MP 204

The Control MP 204 operates with two sets of limits:

• a set of warning limits

• a set of alarm limits, trip.

If one or more of the warning limits are exceeded, the motor

continues to run.

If one of the alarm limits is exceeded, the motor is stopped.

4. Product introduction

The Control MP 204 is used to start and stop the pump according

to an input signal. The input signal comes either from a main

control system, like a PLC, or from a simple input, like a switch.

The built-in MP 204 motor protector will ensure long service life of

the pump.

The Control MP 204 can optionally be fitted with a Grundfos CIU

unit, Communication Interface Unit, enabling transmission of the

collected data.

4.1 Modules

The Control MP 204 is designed to protect the motor both

electrically and mechanically.

MP 204 motor protector

The MP 204 protects the motor electrically by disconnecting the

motor or pump when one of the trip limits has been reached.

Trip conditions:

• Overload

• Underload, dry running

• Temperature, Tempcon sensor, PTC/thermal switch and Pt

sensor

• Missing phase

• Phase sequence

• Overvoltage

• Undervoltage

• Power factor, cos φ

• Current unbalance.

Sensor inputs and output:

• Pt100 or Pt1000 sensor

• PTC sensor.

See installation and operating instructions for the MP 204.

Designation Description

H Hand, manually operated

OOff

A Auto, automatically operated

TM06 9430 2317

Pos. Description

1 "H-O-A" selector switch

2 Red indicator light

3 Main switch

Q00

off

From the factory, the MP 204 is set to automatic

restarting after a trip.

English (GB)

4.2 Grundfos GO Remote

The product is designed for infrared communication with

Grundfos GO Remote. MP 204 must be configured using

Grundfos GO Remote.

Grundfos GO Remote enables setting of functions and gives

access to status overviews, technical product information, alarm

logs and actual operating parameters.

Fig. 9 Grundfos GO Remote communication via infrared

connection, IR

4.2.1 Infrared communication

When communicating via infrared light, Grundfos GO Remote

must be pointed at the control panel.

4.3 Communication

If a Grundfos CIU unit, Communication Interface Unit, is to be

used, we recommend you to fit it according to the wiring diagram

and layout supplied with the Control MP 204.

All variants can be extended with external communication as an

option.

4.4 Identification

4.4.1 Nameplate

Fig. 10 Nameplate

4.4.2 Type key

TM06 6256 2719

Pos. Description

Grundfos MI 301:

Separate module enabling radio or infrared

communication. Use the module together with an

Android or iOS-based smart device with Bluetooth

connection.

TM06 9426 2317

Pos. Description

1 Type designation

2Model.

Product number, serial number and production code.

3 Supply voltage and frequency

4 Order number

5 Rated current

6 Short-circuit current rating

7 Maximum ambient temperature

8 Number of pumps

9 Starting method

10 Imin. / Imax.

11 Enclosure class

12 Approval marks

13 Weight

14 Country of origin

Example Control MP 204 1x 100.0 - 150.0 A DOL U1 AB

Product type

Control range

Number of pumps

Current range of pumps

Starting method

DOL: Direct On Line

SD: Star-Delta

Mains:

U1: 3 x 400 V, 50 Hz, PE

U2: 3 x 400 V, 50 Hz, N, PE

Options:

A: Dry-running protection

B: Magnetic valve with a float switch

MADE IN GERMANY

code

IP Class:

Weight: 341.5 kg

Pumps: 2 13 A 21 A DOL

No. Imin Imax Starting Method

In: 25 A Icc: 10 kA T

ambmax:35

°C

Order No.:

Mains: 3x400 V, 50 Hz, PE

Model: A_Partnumber_Serial number_PX_YYWW

Type: Control MP 204 2x13-21 A DOL U1 A

DK - 8850 - Bjerringbro - Denmark

99049929

11 10

English (GB)

5. Control functions

This section describes the available control modes:

• Switch control

– Control MP 204 controlled by a pressure switch

– Control MP 204 controlled by a float switch

– Control MP 204 controlled by a main control system, for

example a PLC.

5.1 Switch control

Control MP 204 controlled by a pressure switch

If a constant pressure is required in a closed system, a pressure

switch can be connected. The pressure switch starts and stops

the pump according to the setpoint, pressure. Use terminals X10:

3 + 4.

Fig. 11 Example, pressure switch

Control MP 204 controlled by a float switch

If a constant level is required in an open system, a level

sensor,float switch, can be used to start and stop the pump.

When pumping into an open tank or reservoir, the pump is started

when the water level reaches the start level. The pump is stopped

when the stop level is reached.

The digital sensors used must be potential-free switches, like a

float switch or a similar type of switch. Use terminals X10: 3 + 4.

Fig. 12 Example, float switch

Control MP 204 controlled by a main control system

The Control MP 204 is controlled by a main control system, pos.

1, fig. 13, for example a PLC or a similar main control system.

Fig. 13 Example, main control system

6. Taking the product out of operation

6.1 Decommissioning

Observe the following if the product is to be permanently taken

out of operation.

An electrode relay can optionally be installed as

dry-running protection.

TM06 9428 2317

Q00

off

Pump

Pressure

switch

Control MP 204

TM06 9427 2317TM06 9429 2317

WARNING

Electric shock

Death or serious personal injury

Before starting any work on the product, make sure

that the power supply has been switched off and that

it cannot be accidentally switched on.

Q00

off

Pump

Control MP 204

Start

Stop

Buffer tank

Float switch

Q00

off

Pump

Control MP 204

Andere Handbücher für MP 204

Inhaltsverzeichnis

Sprachen:

Andere Grundfos Wasserpumpe Handbücher

Grundfos

Grundfos UPS 15-30 130 Bedienungsanleitung

Grundfos

Grundfos TPE 2 Series Betriebsanleitung

Grundfos

Grundfos 15 BMQE 07B-180 Bedienungsanleitung

Grundfos

Grundfos PM 2 Bedienungsanleitung

Grundfos

Grundfos Hydro Multi-E Series Bedienungsanleitung

Grundfos

Grundfos DWK Series Betriebsanleitung

Grundfos

Grundfos ALPHA1 Series Bedienungsanleitung

Grundfos

Grundfos D Bedienungsanleitung

Grundfos

Grundfos PS.R.05-17 Bedienungsanleitung

Grundfos

Grundfos SE 12-42 hp Betriebsanleitung

Grundfos

Grundfos Multilift M Series Bedienungsanleitung

Grundfos

Grundfos SP Series Bedienungsanleitung

Grundfos

Grundfos Conlift Bedienungsanleitung

Grundfos

Grundfos UPM3 Auto L 70 Bedienungsanleitung

Grundfos

Grundfos MAGNA3 25-80 (N) Bedienungsanleitung

Grundfos

Grundfos DDI 222 Bedienungsanleitung

Grundfos

Grundfos ALPHA SOLAR Bedienungsanleitung

Grundfos

Grundfos NB Bedienungsanleitung

Grundfos

Grundfos DMX 221 Bedienungsanleitung

Grundfos

Grundfos MIXIT Bedienungsanleitung

Grundfos

Grundfos SQ Series Bedienungsanleitung

Grundfos

Grundfos Unilift APG Betriebsanleitung

Grundfos

Grundfos CM Bedienungsanleitung

Grundfos

Grundfos Alpha Solar Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung