Grundfos MTR 15 Betriebsanleitung

Service instructions

MTR 10, 15 and 20

50/60 Hz

1/3~

1 / 18

96548180 0804 GB

Contents

1. Type identification .......................................................................................................................2

1.1 Nameplate......................................................................................................................................................2

1.2 Type key ..........................................................................................................................................................3

1.3 Code for shaft seal........................................................................................................................................4

2. Torques and lubricants................................................................................................................. 5

3. Service tools..................................................................................................................................6

3.1 Special tools ...................................................................................................................................................6

3.2 Standard tools ...............................................................................................................................................6

3.3 Torque tools ................................................................................................................................................... 7

4. Dismantling and assembly ..........................................................................................................8

4.1 Transport bracket .........................................................................................................................................9

4.2 Dismantling the pump.............................................................................................................................. 11

4.3 Assembly.......................................................................................................................................................12

4.4 Checking and replacing impellers/wear rings and neck rings........................................................13

5. Order of assembly for chambers and impellers........................................................................14

5.1 Overview of chambers for MTR 10 .........................................................................................................14

5.2 Positioning of chambers in MTR 10-2 up to MTR 10-16.................................................................... 15

5.3 Positioning of chambers in MTR 10-18 up to MTR 10-22..................................................................16

5.4 Overview of chambers for MTR 15 and MTR 20 .................................................................................. 17

5.5 Positioning of chambers in MTR 15 and MTR 20 ................................................................................18

# / 18

1. Type identification

1.1 Nameplate

TM02 9053 1704

Fig. 1. Nameplate with 60 Hz data

Pos. Description Pos. Description

1 Type designation 10 Country of production

2 Model 11 Frequency

3 Product number 12 Speed

4 Place of production 13 Rated flow rate

5 Production year and week 14 Maximum pressure and temperature

6P215 The number of the copy of the technical file kept

with KEMA (stated if the pump is ATEX classified)

7 Closed valve head, 50 Hz

8 Head at rated flow rate, 50 Hz 16 The serial number of the pump (stated if the

pump is ATEX classified)

Direction of rotation:

CCW: Counter-clockwise

CW: Clockwise 17 ATEX category (stated if the pump is ATEX

classified)

Model A96515006P10420

96505758

min

-1

max

pmax/tmax

bar/˚C

3500

3,6

25/90

0,55

27,1

CCW

000001

Technical file no. XXXXXXXX

Serial No. Made in Taiwan

DK-8850 Bjerringbro

II 2 G c 90 C

MTR3-4/4A-W-A-HUUV

12345

# / 18

1.2 Type key

Example MTR 10 -4 / 4 A -W -A -HUUV

Type range

Rated flow rate m³/h

Number of stages

Number of impellers in the pump

Code for pump version

A = Basic version

B = Oversize motor

P = Undersize adapter flange (one flange size smaller)

T = Oversize adapter flange (two flange sizes bigger)

X = Special version

Code for pipe connections

M = Changed flange connection

W = Internally threaded

Code for materials

A = Standard

I = Stainless steel parts of DIN W.-Nr. 1.4301 / AISI 304 or similar class

Code for shaft seal, see 1.3 Code for shaft seal.

# / 18

1.3 Code for shaft seal

The code for shaft seal always consists of four letters.

The following codes are used:

Example H U U V

Principal Grundfos type designation for

shaft seal 1

Material, rotating seal face 2

Material, stationary seat 3

Material, secondary seal 4

Position Code Description

A O-ring seal with fixed driver

B Rubber bellows seal

C O-ring seal with spring as seal driver

D O-ring seal, balanced

E Cartridge seal with O-ring

F Cartridge seal with rubber bellows

H Balanced cartridge seal with O-ring

K Type M as cartridge seal

M Shaft seal with metal bellows

O Double seal, back-to-back

P Double seal, tandem

R O-ring seal, type A, with reduced sliding surfaces

X Special version

and

B Carbon, synthetic resin-impregnated

C Other types of carbon

S Chromium steel

H Cemented tungsten carbide, embedded (hybrid)

U Cemented tungsten carbide

Q Silicon carbide

V Aluminium oxide

X Other ceramics

EEPDM

FFXM

P NBR (nitrile rubber)

TPFTE

VFKM

K FFKM

# / 18

2. Torques and lubricants

Thread-Eze, part no. SV9997 (0.5 l).

Gardolube L 6034, part no. SV9995 (1 l).

Pos. Designation Quantity Dim. Torque [Nm] Lubricant

7.a Screw 4 M4 3 ± 0.25 -

9 Hexagon socket head screw 4

M6 13 ± 1.5

Thread-EzeM8 31 ± 3

M10 62 ± 6

28 Hexagon head screw 4

M6 ?

Thread-Eze

M8 ?

M12 ?

M16 ?

36 Nut for strap

2M8 18±1

Gardolube

4M10 20 ± 4

M12 50 ± 5

36a Nut 4

M6 5 ± 1

Thread-Eze

M8 12 ± 2

M12 30 ± 3

M16 40 ± 8

105 Shaft seal 1 M33 35 ± 7 Soapy water

113 Set screw 3 M5 2.5 ± 0.25 -

122 Lock nut 1 M8 12 ± 2 Gardolube

M12 40 ± 8

# / 18

3. Service tools

3.1 Special tools

3.2 Standard tools

ABCD

EFGH

Pos. Designation For pos. Description Part number

A Shaft holder for assembly SV0040

BRing insert tool for shaft seal

+ square adapter 105 SV2101

SV2100

C Puller for neck ring 49, 65 SV0239

Pos. Designation For pos. Description Part number

D Bits kit 9, 113 SV2010

EScrewdriver 105 Straight slot -

7a Torx TX20 -

F Ring/open-end spanner 28, 36, 122

M6 - 10 mm SV0083

M8 - 13 mm SV0055

M12 - 19 mm SV0054

M16 - 24 mm SV0122

GSocket 28,36

M6 - 10 mm SV0806

M8 - 13 mm SV0091

M12 - 19 mm SV0267

M16 - 24 mm SV0092

H Plastic hammer No. 2 SV0349

# / 18

3.3 Torque tools

Pos. Designation For pos. Description Part number

I Torque wrench 9, 26b, 28a, 36,

105, 113

1-6 Nm SV0438

4-20 Nm SV0292

20-100 Nm SV0269

J Ratchet insert tool I 9 x 12, ½" x ½" SV0295

# / 18

4. Dismantling and assembly

Position numbers

Position numbers of parts (digits) refer to exploded views, sectional drawings and parts lists; position

numbers of tools (letters) refer to 3. Service tools.

Before dismantling

• Disconnect the electricity supply to the motor.

• Close the isolating valves, if fitted, to avoid draining the system.

• Remove the electric cable in accordance with local regulations.

• Note the centre of gravity of the pump to prevent it from overturning. This is especially important in the

case of long pumps.

Before assembly

Gaskets and O-rings should always be replaced when the pump is overhauled.

• Clean and check all parts.

• Order the necessary service kits.

• Replace defective parts by new parts.

During assembly

• Lubricate and tighten screws and nuts to the torque stated, see 2. Torques and lubricants.

# / 18

4.1 Transport bracket

To protect the bearings and the shaft seal, a transport bracket must always be used when transporting the

pump without motor.

4.1.1 Fitting the transport bracket

1. Press home the shaft pos. 51.

2. Press home the driver of the shaft seal pos. 105 and tighten the three screws pos. 113.

3. Lift the shaft pos. 51 and fit the adjusting fork.

4. Fit the coupling pos. 8 and the screws pos. 9, but leave loose.

5. Fit the transport bracket.

6. Fit the two screws and nuts pos. 703 and 704, but leave loose.

7. Tighten the screws pos. 9 in the coupling.

8. Tighten the screws pos. 703.

9. Remove the adjusting fork.

10. The pump can now be transported without motor.

Fig. 1 Transport bracket pos. 700

Fig. 2 Transport bracket pos. 701 and 702

Flange size

Fig. 1 Fig. 2 Hexagon head screw

pos. 703

(2 pcs.)

Nut

pos. 704

(2 pcs.)

Transport bracket complete

pos. 700

Shaft stub

pos. 701

Rail

pos. 702

F85 96521627 - - ID8022 M6 x 20 96429513

F100 96521627 - - ID8023 M6 x 25 96429513

F115 96521626 - - ID8024 M8 x 20 ID0825

F130 96521626 - - ID8025 M8 x 25 ID0825

F265 - 96508079 96508073 ID7904 M12 x 30 None

F300 - 96508080 96508073 ID7905 M16 x 45 ID7908

56C - 96508075 96508072 ID1839 UNC 3/8" x 25 96120884

182TC - 96508076 96508074 ID1840 UNC 1/2" x 25 96467385

213TC - 96508077 96508074 ID0185 UNC 1/2" x 1 ½" 96467385

254TC - 96508078 96508074 96491112 UNC 1/2" x 2 ½" 96467385

284TSC - 96508078 96508074 ID1840 UNC 1/2" x 25 96467385

703

700

704

703

702

704

701

M10x20

# / 18

4.1.2 Removing the transport bracket

It is very important to proceed according to these instructions, as the shaft seal may otherwise be damaged.

1. Remove three of the screws pos. 9.

2. Slacken the last screw pos. 9, but do not unscrew it completely.

3. Hit the end of the hexagon key carefully with the flat of the hand to loosen one of the coupling halves.

4. Remove the last screw pos. 9 and the loose coupling half.

5. Hit the flat part of the coupling half on the shaft end very carefully.

6. Remove the coupling half when it is loose.

7. Remove the screws pos. 703 and the nuts pos. 704 and remove the transport bracket.

8. Slacken the screws pos. 113 by ¼ turn.

9. Lift the shaft pos. 51 and fit the adjusting fork.

10. Tighten the screws pos. 113 with 2.5 Nm.

11. Fit the motor to the pump head.

12. Fit the screw pos. 28, lubricate and tighten them diagonally to the torque stated, see 2. Torques and

lubricants.

13. Fit the pin pos. 10 and the two coupling halves pos. 10a.

14. Lubricate the four screws pos. 9 with Thread-Eze and fit them.

15. Check that the gaps either side of the coupling halves are equal.

16. Tighten the screws pos. 9 to the torque stated, see 2. Torques and lubricants, and remove the adjusting

fork.

17. Check that the shaft rotates freely and noiselessly.

18. Place the adjusting fork on the inside of one of the coupling guards.

19. Fit the coupling guards pos. 7 and the screws pos. 7a.

TM02 9558 3204

Fig. 3 Gaps between coupling halves

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Grundfos Wasserpumpe Handbücher

Grundfos

Grundfos 97632133 Bedienungsanleitung

Grundfos

Grundfos BMPX Bedienungsanleitung

Grundfos

Grundfos SP Betriebsanleitung

Grundfos

Grundfos CR Series Bedienungsanleitung

Grundfos

Grundfos DMB Series Bedienungsanleitung

Grundfos

Grundfos TP Betriebsanleitung

Grundfos

Grundfos PS.R.05-17 Bedienungsanleitung

Grundfos

Grundfos Conlift Bedienungsanleitung

Grundfos

Grundfos PS.R.05 Bedienungsanleitung

Grundfos

Grundfos TPE 1000 Series Bedienungsanleitung

Grundfos

Grundfos MAGNA 2000 Series Bedienungsanleitung

Grundfos

Grundfos DWK Bedienungsanleitung

Grundfos

Grundfos CM Booster PM1 Bedienungsanleitung

Grundfos

Grundfos Hydro Multi-E Series Bedienungsanleitung

Grundfos

Grundfos MIXIT Bedienungsanleitung

Grundfos

Grundfos SL1 Series Bedienungsanleitung

Grundfos

Grundfos NK Bedienungsanleitung

Grundfos

Grundfos KPC Series Bedienungsanleitung

Grundfos

Grundfos DMH 25 Series Bedienungsanleitung

Grundfos

Grundfos SEG Series Bedienungsanleitung

Grundfos

Grundfos JP5 Bedienungsanleitung

Grundfos

Grundfos DME series Bedienungsanleitung

Grundfos

Grundfos BME Bedienungsanleitung

Grundfos

Grundfos MTH Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung