Grundfos SB Bedienungsanleitung
SB, SBA
Installation and operating instructions
GRUNDFOS INSTRUCTIONS
SB, SBA
English (GB)
Installation and operating instructions ..................................5
Български (BG)
Упътване за монтаж и експлоатация.................................19
Čeština (CZ)
Montážní a provozní návod ........................................35
Deutsch (DE)
Montage- und Betriebsanleitung .....................................49
Dansk (DK)
Monterings- og driftsinstruktion ......................................65
Eesti (EE)
Paigaldus- ja kasutusjuhend........................................79
Español (ES)
Instrucciones de instalación y funcionamiento............................93
Suomi (FI)
Asennus- ja käyttöohjeet .........................................108
Français (FR)
Notice d'installation et de fonctionnement..............................122
Ελληνικά (GR)
Οδηγίες εγκατάστασης και λειτουργίας................................137
Hrvatski (HR)
Montažne i pogonske upute .......................................153
Magyar (HU)
Telepítési és üzemeltetési utasítás ..................................167
Italiano (IT)
Istruzioni di installazione e funzionamento .............................182
Lietuviškai (LT)
Įrengimo ir naudojimo instrukcija ....................................197
Latviešu (LV)
Uzstādīšanas un ekspluatācijas instrukcija .............................211
Nederlands (NL)
Installatie- en bedieningsinstructies ..................................227
Polski (PL)
Instrukcja montażu i eksploatacji....................................243
3
Table of contents
Português (PT)
Instruções de instalação e funcionamento .............................258
Română (RO)
Instrucţiuni de instalare şi utilizare...................................273
Srpski (RS)
Uputstvo za instalaciju i rad .......................................288
Русский (RU)
Паспорт, Руководство по монтажу и эксплуатации......................303
Svenska (SE)
Monterings- och driftsinstruktion ....................................318
Slovensko (SI)
Navodila za montažo in obratovanje .................................332
Slovenčina (SK)
Návod na montáž a prevádzku .....................................347
Türkçe (TR)
Montaj ve kullanım kılavuzu .......................................361
Українська (UA)
Інструкції з монтажу та експлуатації ................................375
Bosanski (BS)
Montažne i pogonske upute .......................................390
Macedonian (MK)
Упатства за монтирање и ракување ................................405
(AR) ةيبرعلا
.............................................420
4SB, SBA
Table of contents
English (GB) Installation and operating instructions
Original installation and operating instructions
Table of contents
1. General Information ............. 5
1.1 Hazard statements .............. 5
1.2 Notes ..................... 6
2. Receiving the product............ 6
2.1 Inspecting the packaging ........... 6
2.2 Scope of delivery ............... 6
3. Installing the product ............ 6
3.1 Location .................... 6
3.2 Mechanical installation ............ 8
3.3 Pump position................. 8
3.4 Connecting the outlet hose or pipe ...... 9
3.5 Non-return valve for SB pumps........ 9
3.6 Electrical connection ............. 9
4. Starting up the product ...........10
4.1 SBA starting and stopping conditions ....10
5. Handling and storing the product .....11
5.1 Handling the product .............11
5.2 Storing the product ..............11
5.3 Frost protection ................11
6. Product introduction ............11
6.1 Product description ..............11
6.2 SB pumps ...................11
6.3 SBA pumps ..................11
6.4 SBA dry-running protection..........11
6.5 Intended use .................12
6.6 Pumped liquids ................12
6.7 Identification..................12
7. Maintaining the product...........13
8. Fault finding the product ..........14
8.1 The pump does not run. ...........14
8.2 The pump runs but gives no water.......15
8.3 The pump runs at reduced performance. ..15
8.4 Frequent starts and stops. ..........16
8.5 Leaking water from the drain holes......16
9. Technical data ................17
9.1 Operating conditions .............17
9.2 Mechanical data................17
9.3 Electrical data .................18
10. Further product information ........18
11. Disposing of the product ..........18
1. General Information
Read this document before you install the
product. Installation and operation must
comply with local regulations and accepted
codes of good practice.
This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or mental
capabilities or lack of experience and
knowledge if they have been given
supervision or instruction concerning use
of the appliance in a safe way and
understand the hazards involved.
Children shall not play with the appliance.
Cleaning and user maintenance shall not
be made by children without supervision.
1.1 Hazard statements
The symbols and hazard statements below may
appear in Grundfos installation and operating
instructions, safety instructions and service
instructions.
DANGER
Indicates a hazardous situation which, if
not avoided, will result in death or serious
personal injury.
WARNING
Indicates a hazardous situation which, if
not avoided, could result in death or
serious personal injury.
CAUTION
Indicates a hazardous situation which, if
not avoided, could result in minor or
moderate personal injury.
The hazard statements are structured in the following
way:
SIGNAL WORD
Description of the hazard
Consequence of ignoring the warning
• Action to avoid the hazard.
5
English (GB)
1.2 Notes
The symbols and notes below may appear in
Grundfos installation and operating instructions,
safety instructions and service instructions.
Observe these instructions for explosion-
proof products.
A blue or grey circle with a white graphical
symbol indicates that an action must be
taken.
A red or grey circle with a diagonal bar,
possibly with a black graphical symbol,
indicates that an action must not be taken
or must be stopped.
If these instructions are not observed, it
may result in malfunction or damage to the
equipment.
Tips and advice that make the work easier.
2. Receiving the product
2.1 Inspecting the packaging
On receipt of the product, do the following:
1. Check that the product is as ordered. If the
product is not as ordered, contact the supplier.
2. Check that no visible parts have been damaged. If
any visible parts have been damaged, contact the
transport company.
2.2 Scope of delivery
The box contains the following items:
• 1 pump
• 1 adapter
• 1 installation and operating instructions
• 1 quick guide
• 1 floating inlet strainer, for side inlet variant only
• 1 non-return valve, for SB only.
3. Installing the product
Make sure that the system in which the
pump is incorporated is designed for the
maximum pump pressure.
This pump has been evaluated for use
with water only.
Observe local regulations concerning limits
for manual lifting or handling.
CAUTION
Crushing of feet
Minor or moderate personal injury
‐Use safety shoes when handling the
pump.
DANGER
Electric shock
Death or serious personal injury
‐Switch off the power supply before you
start any work on the product. Make
sure that the power supply cannot be
accidentally switched on.
3.1 Location
Install the pump in a frost-free location.
Before the pump is submerged in the well or tank,
make sure that the well or tank does not contain sand
or solid sediment.
Install the pipe so that the pump is not exposed to
mechanical stress.
3.1.1 Maximum installation depth
Read the label on the product.
Product Maximum installation depth
[m]
SB 10
SBA 10
6
English (GB)
3.1.2 Highest tapping point for SBA pumps
Install SBA pumps so that the height between the
pump and the highest tapping point does not exceed
these values:
SBA 3-35: 13 m.
SBA 3-45: 20 m.
Max.
13 m/43 ft
Max.
20 m/66ft
SBA 3-35 SBA 3-45
TM067648
Highest tapping point for SBA
Related information
8.4 Frequent starts and stops.
3.1.3 Minimum space
Pumps installed with a float switch require a free
space between the float switch and the wall to ensure
free movability.
Pumps with side inlet require a free space between
the floating inlet strainer and the wall.
If you install the pump in a well or tank, the minimum
free space must be as shown in the figure below.
Pumps installed without a float switch require a space
that corresponds to the physical dimensions of the
pump.
SB and SBA pump with a float switch and side
inlet
TM082302
Minimum space for SB and SBA pump in a well or
tank
7
English (GB)
3.1.4 Adjustment of the float switch
To make sure that the float switch can start and stop
the pump, adjust the start and stop level by changing
the free cable length between the float switch and the
lifting handle.
A reduced free cable length results in more starts and
stops and a small difference in level. The minimum
free cable length is 10-18 cm. See fig. Minimum free
cable length for float switch.
• An increased free cable length results in fewer
starts and stops and a large difference in level.
Make sure that the float switch can move freely.
Make sure that the stop level does not fall below the
pump inlet strainer.
TM082305
Minimum free cable length for float switch
3.2 Mechanical installation
3.2.1 Lifting the product
Lift the pump by the lifting handle. Never lift the pump
by the power cable. Tie a rope to the lifting handle or
lifting eye instead.
Do not lift the product by the power cable.
Lift the product by means of a rope.
TM071402
Lifting the pump
Related information
3.3.1 Pump position of SB and SBA
3.3 Pump position
3.3.1 Pump position of SB and SBA
Use the pump in the vertical position as shown in fig.
Position of SB, SBA pumps.
TM082310
Position of SB, SBA pumps
Related information
3.2.1 Lifting the product
8
English (GB)
3.4 Connecting the outlet hose or pipe
Product External pipe thread
[inch]
SB G 3/4" or 1"
SBA G 3/4" or 1"
The outlet hose or pipe can be connected to the
pump outlet port by means of an adapter. You can
also connect a pipe directly to the pump outlet.
SB and SBA pumps include an adapter. Cut off the
adapter so that it matches the outlet port diameter.
TM082301
TM082365
3.5 Non-return valve for SB pumps
Connect the non-return valve to the SB pump outlet.
The non-return valve has G 1" threads for connection
to the adapter or the pipe.
TM082297
Non-return valve
3.6 Electrical connection
DANGER
Electric shock
Death or serious personal injury
‐Switch off the power supply before you
start any work on the product. Make
sure that the power supply cannot be
accidentally switched on.
‐The pump must be earthed.
DANGER
Electric shock
Death or serious personal injury
‐The protective earth of the socket
outlet must be connected to the
protective earth of the pump. The plug
must therefore have the same PE
connection system as that of the
socket outlet. If not, use a suitable
adapter.
We recommend that you fit the permanent
installation with a residual-current circuit
breaker, RCCB, with a tripping current less
than 30 mA.
DANGER
Electric shock
Death or serious personal injury
‐If the pump is used for cleaning or
other maintenance of swimming pools,
garden ponds or similar places, make
sure that the pump is supplied through
a residual-current circuit breaker,
RCCB, with a tripping current of 30
mA.
DANGER
Electric shock
Death or serious personal injury
‐Connect pumps that are delivered
without cable and/or plugs to an
external main switch with a minimum
contact gap of 3 mm in all poles.
Make sure that there is at least 3 m free
cable above the liquid level.
Check that the supply voltage and frequency
correspond to the values stated on the pump
nameplate.
The electrical connection must be carried out by an
authorised electrician in accordance with local
regulations.
9
English (GB)
3.6.1 Thermal protection
The pump has a built-in thermal switch and requires
no additional motor protection. If the pump is running
without water, or if it is otherwise overloaded, the
built-in thermal switch will cut out. When the motor
has cooled to normal temperature, it will restart
automatically.
3.6.2 Connecting to external controller
SB
SB pumps must be connected to an external
controller. We recommend a Grundfos Pressure
Manager: net.grundfos.com/qr/i/97506325
SBA
SBA pumps have an integrated control unit.
Related information
6.2 SB pumps
6.3 SBA pumps
3.6.3 Power supply failure
In case of a power supply failure, the pump restarts
automatically when power returns and runs for at
least 10 s.
4. Starting up the product
WARNING
Flammable material
Death or serious personal injury
‐Do not use the pump for flammable
liquids, such as diesel oil, petrol or
similar liquids.
DANGER
Electric shock
Death or serious personal injury
‐Do not use the pump in swimming
pools, garden ponds or similar places if
there are people in the water.
1. Open a tap in the system.
2. Switch on the power supply.
3. Check that the pump is running and water is
coming out of the tap.
4. Check that the pump is running and pressure is
being built up in the system.
5. Close the tap.
6. Check that pressure has been built up in the
system.
7. Check that the pump stops after 10 seconds.
Water is accumulated between the motor
housing and cover during submersion.
When the pump is stopped and lifted from
a submerged position, so the drain holes
are above water level, the water is drained
from the drain holes located under the red
ring.
TM083090
Connect SB pumps to an external
controller.
Related information
8.5 Leaking water from the drain holes
4.1 SBA starting and stopping conditions
When water is consumed in the water supply system,
the pump starts when the starting conditions are
fulfilled. This happens for example when a tap is
opened which makes the pressure in the system
drop. The control unit stops the pump again when
consumption stops, that is when the tap is closed.
Starting conditions
The pump starts when one of the following conditions
is fulfilled:
• The flow rate is higher than the minimum flow
rate.
• The pressure is lower than the start pressure.
Stopping conditions
The pump stops with a time delay of 10 s when the
flow rate is lower than the minimum flow rate.
The start pressure and minimum flow rate values are
shown in sections Pressure and Flow rate.
10
English (GB)
Andere Handbücher für SB
3
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Grundfos Wasserpumpe Handbücher
Grundfos
Grundfos SP Series Betriebsanleitung
Grundfos
Grundfos SE1 50 Montageanleitung
Grundfos
Grundfos TPE 2 Series Bedienungsanleitung
Grundfos
Grundfos DMH 28 Series Bedienungsanleitung
Grundfos
Grundfos SP Bedienungsanleitung
Grundfos
Grundfos Home Booster 4.5 Handbuch
Grundfos
Grundfos TPE 2 Series Betriebsanleitung
Grundfos
Grundfos UNILIFT AP35B Bedienungsanleitung
Grundfos
Grundfos SCALA1 Bedienungsanleitung
Grundfos
Grundfos Multilift MD Bedienungsanleitung
Grundfos
Grundfos PS.W.04-20 Bedienungsanleitung
Grundfos
Grundfos MIXIT Bedienungsanleitung
Grundfos
Grundfos GT-C Bedienungsanleitung
Grundfos
Grundfos PS.W.04-20 Bedienungsanleitung
Grundfos
Grundfos TPE Series Betriebsanleitung
Grundfos
Grundfos CHI Series Bedienungsanleitung
Grundfos
Grundfos NBS 025-095/08.43AAEG6S3ESBQQETX2 Bedienungsanleitung
Grundfos
Grundfos alpha2 l Bedienungsanleitung
Grundfos
Grundfos ALPHA Bedienungsanleitung
Grundfos
Grundfos SPO Bedienungsanleitung
Beliebte Wasserpumpe Handbücher anderer Marken
Sykes AmeriPumps
Sykes AmeriPumps GP100M Fehlerbehebungshandbuch
DUROMAX
DUROMAX XP WX Series Bedienungsanleitung
BRINKMANN PUMPS
BRINKMANN PUMPS SBF550 Bedienungsanleitung
Franklin Electric
Franklin Electric IPS Bedienungsanleitung
Xylem
Xylem e-1532 Series Bedienungsanleitung
Milton Roy
Milton Roy PRIMEROYAL Bedienungsanleitung