Grundig GCA-B2323T Bedienungsanleitung
GCA-B2323T.8.2.27.10.2010
Owner´s Manual
EN
© ASP AG
Cameras & Domes
GCA-B2323T 1/3" Outdoor Varifocal Camera with IR LED
VSS Nederland
Video Systems
e
VSS Nederland B.V. - Telfordstraat 11m - 8013 RL Zwolle - Tel.: +31 38 42 89 420 - Fax: +31 38 42 89 429 - E-mail: [email protected]
Content:
1. Important Safety Instructions 1
2. Package Contents 2
3. Installation 3
1. Parts Name 3
2. Connections 4
3. Mounting the camera 4
4. Zoom & Focus Adjustment 5
5. IR-LED Brightness Dip Switch 6
4. OSD Menu 6
1. OSD Controls 6
2. Main menu 7
3. Camera Setup 8
4. Intelligence 15
5. Privacy Zone 16
6. Other Set 17
7. Communication 18
8. System Info 18
9. Language 18
1. Important Safety Instructions
Be sure to use only the standard adapter that is specified in the specification sheet.
Using any other adapter could cause fire, electrical shock, or damage to the product.
Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product. Do not connect multiple cameras to a single
adapter. Exceeding the capacity may cause abnormal heat generation or fire.
Do not place conductive objects (e.g. screwdrivers, coins or any metal items) or
containers filled with water on top of the camera. Doing so may cause personal injury
due to fire, electric shock, or falling objects.
1English
If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued use
in such a condition may cause fire or electric shock.
If this product fails to operate normally, contact the nearest service center. Never
disassemble or modify this product in any way. (GRUNDIG is not liable for problems
caused by unauthorized modifications or attempted repair.)
To prevent fire or electric shock, do not expose the inside of this device to rain or
moisture.
2. Package Contents
These parts are included:
3. Installation
Do not install in a location subject to high temperature (over 50°C), low temperature
(below -10°C), or high humidity. Doing so may cause fire or electric shock. Keep out of
direct sunlight and heat radiation sources. It may cause fire. Avoid aiming the camera
directly towards extremely bright objects such as sun, as this may damage the CCD
image sensor.
Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or
electric shock. Install it in a place with good ventilation.
When installing the camera, fasten it securely and firmly. A falling camera may cause
personal injury.
If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
2English
3.1. Parts Name
1. Sun-Shield Bolt
2. Sun-Shield
3. Front Case
4. Rear Case
5. Service Monitor Port Cap
6. Bracket
7. Video/Power Cable
3English
3.2. Connections
- Power connection: Requires DC 12V or AC 24V input depending on camera model.
- All camera models are supplied with service monitor output on the camera module. A
service monitor and control cable is included in the package.
Note:
To set up OSD menu externally, service monitor and control cable is required.
3.3. Mounting the camera
- Install the Mounting Bracket at the desired location. Using screws supplied fix the
bracket to the wall.
- Adjust the camera according to your requirements with the supplied wrench (see
picture).
4English
3.4. Zoom & Focus Adjustment
1. Unscrew Front Case from the Rear Case.
2. Loosen Zoom & Focus screws and make necessary adjustments as shown.
- Field of View: Telephoto (T) to Wide (W)
- Focus: Near (N) to Infinity (oo)
3. Replace the Front Case back on to the Rear Case.
4. Cover the camera with the Sun-Shield and fix it with the Sun-Shield bolt.
5English
3.5. IR-LED Brightness Dip Switch
4. OSD Menu
4.1. OSD Controls
4.1.1. OSD Control Keys
- SETUP key: Accesses to the menu mode or confirms the setting.
- UP (/\) / DOWN (\/): Chooses the desired menu.
- LEFT (<) / RIGHT (>): Sets up the value of the selected menu.
6English
4.1.2. OSD Icons
Exits the menu setting. Before you exit
make sure you SAVE your settings, or
select QUIT to cancel.
Returns to the previous menu.
Returns to the main menu.
Use this to SAVE your settings of MASK
AREA, PRIVACY ZONE and more. Once
you saved your settings, they will remain
even if you select QUIT in the menu.
Use this to delete your settings of MASK
AREA, PRIVACY ZONE and more. Once
you saved your settings, they will not be
restored even if you select QUIT in the
menu.
4.2. Main menu
1. Press the SETUP key and hold it for a while to access the menu mode.
2. Select the desired feature by using UP/DOWN keys (/\ \/) on the control.
CAMERA SET: Here you can configure
camera related functions and data.
INTELLIGENCE: You can configure the
settings of motion detection, tracking and
more.
PRIVACY ZONE: You can configure the
privacy related settings.
OTHER SET: You can configure for factory
defaults, and more.
7English
COMMUNICATION: Configures the settings regarding the RS-485 communication.
SYSTEM INFO: Displays the system information including the camera version and
communication settings.
LANGUAGE: Select a preferred language from those listed.
4.3. Camera Setup
CAMERA ID [OFF, ON] :
It is used to switch on/off the camera id. If
camera id is switched ON you can access
the CAMERA ID menu to programm the
camera text.
IRIS [ALC, ELC] :
The IRIS menu is used if you want to adjust
the intensity of light incoming into the
camera.
MOTION [S.SLOW, SLOW, NORM, FAST, F.FAST] :
This menu is used to adjust the strength of the AGC level for a control of the camera
motion. You can select from S.SLOW, SLOW, NORM, FAST and F.FAST for the AGC
level. If you monitor fast moving objects in a low contrast scene, select F.FAST while
select S.SLOW for hardly moving objects in the same lighting condition.
Note:
- This is only available if the SENS-UP menu is set to AUTO.
- If the DAY/NIGHT menu of CAMERA SET is set to AUTO, the MOTION menu will be
deactivated.
DNR [OFF, LOW, MID, HIGH, USER (1~16)] :
You can configure the DNR (Digital Noise Reduction) related settings. It reduces the
noise on the screen. This is especially useful for a severely distorted screen. You can
set the level if you set DNR to USER.
SHUTTER [OFF, AUTO 1/120~1/10K, 1/120~1/10K] :
You can select one of 7 options from 1/120 to 1/10K for the fixed high speed electronic
shutter, which is mostly used for imaging a fast moving object. The auto high speed
electronic shutter operates as the fixed high speed shutter in a high contrast scene but
automatically focuses the target if the iris opens fully in a low contrast scene like in ELC
mode. When it gets bright again, the mode will switch to the fixed high speed electronic
shutter mode. However, the auto high speed shutter operates properly only in a camera
featuring a DC or VIDEO lens.
8English
Inhaltsverzeichnis
Andere Grundig Sicherheitskamera Handbücher
Grundig
Grundig GCA-B1005B Bedienungsanleitung
Grundig
Grundig GCA-B0005B Bedienungsanleitung
Grundig
Grundig GD-CI-CC2616V Bedienungsanleitung
Grundig
Grundig GU-CI Series Bedienungsanleitung
Grundig
Grundig GD-CI-AP6637T Bedienungsanleitung
Grundig
Grundig GD-CI-BC2615M Bedienungsanleitung
Grundig
Grundig GD-CI-AT4747P Bedienungsanleitung
Grundig
Grundig Reason GCI-K2795P-1 Bedienungsanleitung
Grundig
Grundig GCT-K0126V Bedienungsanleitung
Grundig
Grundig GCA-B2357T Bedienungsanleitung
Grundig
Grundig GD-CI-BP8637V Bedienungsanleitung
Grundig
Grundig GD-CI-AC1616V Bedienungsanleitung
Grundig
Grundig GD-TI-BP1603T Bedienungsanleitung
Grundig
Grundig GCA-B0326D Bedienungsanleitung
Grundig
Grundig GD-CI-AC4637P Bedienungsanleitung
Grundig
Grundig GCI-F0576TH-1 Bedienungsanleitung
Grundig
Grundig GD-CI-AP4617C Bedienungsanleitung
Grundig
Grundig GD-CT-AC2126V Bedienungsanleitung
Grundig
Grundig GD-TI-CT2510T Bedienungsanleitung
Grundig
Grundig GD-CI-AT2505B Bedienungsanleitung
