GW Instek ASD Series Bedienungsanleitung

Programmable AC Power Supply

ASD-1150

USER MANUAL

ISO-9001 CERTIFIED MANUFACTURER

This manual contains proprietary information, which is protected by

photocopied, reproduced or translated to another language without

prior written consent of Good Will company.

The information in this manual was correct at the time of printing.

However, Good Will continues to improve products and reserves the

rights to change specification, equipment, and maintenance

procedures at any time without notice.

Good Will Instrument Co., Ltd.

No. 7-1, Jhongsing Rd., Tucheng Dist., New Taipei City 236, Taiwan.

SAFETY INSTRUCTIONS

Table of Contents

SAFETY INSTRUCTIONS .................................................. 5

GETTING STARTED.......................................................... 9

Main Features.......................................................... 10

Appearance.............................................................. 12

INSTALLATION .............................................................. 16

Preparation for Use ................................................. 17

Requirements of Input Power .................................. 17

Input Connection ..................................................... 18

Output Connection .................................................. 20

Power on ................................................................. 21

LOCAL OERATION ......................................................... 23

Operation through Keypad and Knob ....................... 25

Menu Tree ............................................................... 27

Main Menu Setting .................................................. 28

Advanced Parameter Setting Menu .......................... 30

SETUP Function ....................................................... 31

CONFIG Function .................................................... 43

APPLICAION.................................................................. 54

LIST Mode ............................................................... 55

PULSE Mode............................................................ 59

STEP Mode .............................................................. 62

SYNTHESIS Self-Deﬁned Waveform Mode ............... 65

SAVE AND RECALL......................................................... 68

Save and recall the main page setting...................... 69

Save and recall the system setting ........................... 71

ASD-1150 User Manual

REMOTE OPERAION.......................................................74

Set GPIB address and RS-232 Parameters ................ 75

Programming........................................................... 77

Command List ......................................................... 80

Command for Remote Control ................................. 83

APPENDIX ....................................................................114

Protection .............................................................. 115

Specifications ........................................................ 117

Certificate Of Compliance ...................................... 121

TTL Pin Assignment............................................... 122

Built In Waveforms ................................................ 123

SAFETY INSTRUCTIONS

This chapter contains important safety

instructions that you must follow during

operation and storage. Read the following before

any operation to insure your safety and to keep

the instrument in the best possible condition.

Safety Symbols

These safety symbols may appear in this manual or on the

instrument.

WARNING

Warning: Identifies conditions or practices that

could result in injury or loss of life.

CAUTION

Caution: Identifies conditions or practices that

could result in damage to the ASD-1150 or to other

properties.

DANGER High Voltage

Attention Refer to the Manual

Protective Conductor Terminal

Earth (ground) Terminal

Do not dispose electronic equipment as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased.

ASD-1150 User Manual

Safety Guidelines

General

Guideline

CAUTION

Do not place any heavy object on the ASD-1150.

Avoid severe impact or rough handling that

leads to damaging the ASD-1150.

Do not discharge static electricity to the ASD-

1150.

Use only mating connectors, not bare wires, for

the terminals.

Do not block the cooling fan opening.

Do not disassemble the ASD-1150 unless you

are qualified.

(Measurement categories) EN61010-1:2010 and EN61010-2-030

specifies the measurement categories and their requirements as

follows. The ASD-1150 falls under category II.

Measurement category IV is for measurement performed at the

source of low-voltage installation.

Measurement category III is for measurement performed in the

building installation.

Measurement category II is for measurement performed on the

circuits directly connected to the low voltage installation.

0 is for measurements performed on circuits not directly

connected to Mains.

Power Supply

WARNING

AC Input voltage range: 85Vac~265Vac

Frequency: 47Hz to 63Hz

To avoid electrical shock connect the protective

grounding conductor of the AC power cord to

an earth ground.

Cleaning the

ASD-1150

Disconnect the power cord before cleaning.

Use a soft cloth dampened in a solution of mild

detergent and water. Do not spray any liquid.

Do not use chemicals containing harsh material

such as benzene, toluene, xylene, and acetone.

SAFETY INSTRUCTIONS

Operation

Environment

Location: Indoor, no direct sunlight, dust free,

almost non-conductive pollution (Note below)

Relative Humidity: 20%~ 85% (no condensation)

Altitude: < 2000m

Temperature: 0°C to 50°C

(Pollution Degree) EN61010-1:2010 and EN61010-2-030 specifies

the pollution degrees and their requirements as follows. The ASD-

1150 falls under degree 2.

Pollution refers to “addition of foreign matter, solid, liquid, or

gaseous (ionized gases), that may produce a reduction of dielectric

strength or surface resistivity”.

Pollution degree 1: No pollution or only dry, non-conductive

pollution occurs. The pollution has no influence.

Pollution degree 2: Normally only non-conductive pollution

occurs. Occasionally, however, a temporary conductivity caused

by condensation must be expected.

Pollution degree 3: Conductive pollution occurs, or dry, non-

conductive pollution occurs which becomes conductive due to

condensation which is expected. In such conditions, equipment

is normally protected against exposure to direct sunlight,

precipitation, and full wind pressure, but neither temperature

nor humidity is controlled.

Storage

environment

Location: Indoor

Temperature: -25°C to 70°C

Relative Humidity: ≤90%(no condensation)

Disposal

Do not dispose this instrument as unsorted

municipal waste. Please use a separate collection

facility or contact the supplier from which this

instrument was purchased. Please make sure

discarded electrical waste is properly recycled to

reduce environmental impact.

ASD-1150 User Manual

Power cord for the United Kingdom

When using the power supply in the United Kingdom, make sure

the power cord meets the following safety instructions.

NOTE: This lead/appliance must only be wired by competent persons

WARNING: THIS APPLIANCE MUST BE EARTHED

IMPORTANT: The wires in this lead are coloured in accordance with the

following code:

Green/ Yellow:

Earth

Blue:

Neutral

Brown:

Live (Phase)

As the colours of the wires in main leads may not correspond with

the coloured marking identified in your plug/appliance, proceed

as follows:

The wire which is coloured Green & Yellow must be connected to

the Earth terminal marked with either the letter E, the earth symbol

or coloured Green/Green & Yellow.

The wire which is coloured Blue must be connected to the terminal

which is marked with the letter N or coloured Blue or Black.

The wire which is coloured Brown must be connected to the

terminal marked with the letter L or P or coloured Brown or Red.

If in doubt, consult the instructions provided with the equipment

or contact the supplier.

This cable/appliance should be protected by a suitably rated and

approved HBC mains fuse: refer to the rating information on the

equipment and/or user instructions for details. As a guide, a cable

of 0.75mm2should be protected by a 3A or 5A fuse. Larger

conductors would normally require 13A types, depending on the

connection method used.

Any exposed wiring from a cable, plug or connection that is

engaged in a live socket is extremely hazardous. If a cable or plug is

deemed hazardous, turn off the mains power and remove the cable,

any fuses and fuse assemblies. All hazardous wiring must be

immediately destroyed and replaced in accordance to the above

standard.

GETTING STARTED

This manual describes the specifications,

installation and operation instructions of GW

Instek ASD-1150 programmable AC/DC Power

Source. In this manual the term, AC/DC Source,

stands for GW Instek ASD-1150 programmable

AC/DC Source.

The AC source is a high eﬃciency programmable

AC power source, which provides low distortion

sinusoid AC voltage output and measurement.

Stable voltage and frequency are obtained

through accurate digital calculation provided by

DSP IC. Remote programming is accomplished

either by the GPIB bus or the RS-232C serial port.

Main Features.......................................................... 10

Accessories........................................................................................11

Appearance.............................................................. 12

Front Panel........................................................................................12

Rear Panel.......................................................................................... 15

ASD-1150 User Manual

Main Features

Configuration

Local operation from the front panel keypad.

Protection against Over-power, Over-load,

Over-temperature and Fan-fail.

Fan speed controlled by output power.

Built-in isolation output relays.

Remote operation via GPIB or RS-232C

interface.

Input/output

Selective output voltage ranges with full scale of

150V/15A and 300V/7.5A

V, I, F, P, CF, PF, Ip, Is, VA and VAR

measurements

Remote inhibit control

AC ON/OFF, DC ON/OFF, FAULT OUT TTL

output signal.

Andere Handbücher für ASD Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere GW Instek Stromversorgung Handbücher

GW Instek

GW Instek PEL-3000 Series Bedienungsanleitung

GW Instek

GW Instek GPD-303S Series Bedienungsanleitung

GW Instek

GW Instek PSW Series Bedienungsanleitung

GW Instek

GW Instek SPS-1230 Bedienungsanleitung

GW Instek

GW Instek SPD-3606 Bedienungsanleitung

GW Instek

GW Instek ASD Series Bedienungsanleitung

GW Instek

GW Instek PSP-603 Bedienungsanleitung

GW Instek

GW Instek GRA-441 Bedienungsanleitung

GW Instek

GW Instek PSH-1070AGP Bedienungsanleitung

GW Instek

GW Instek PSW 30-72 Betriebsanleitung

GW Instek

GW Instek PEL-500 Series Bedienungsanleitung

GW Instek

GW Instek PSU Series Bedienungsanleitung

GW Instek

GW Instek PFR-100L Betriebsanleitung

GW Instek

GW Instek PHX 60-100 Bedienungsanleitung

GW Instek

GW Instek PSH series Bedienungsanleitung

GW Instek

GW Instek PSB-1400M Bedienungsanleitung

GW Instek

GW Instek PSP-603 Bedienungsanleitung

GW Instek

GW Instek PEL-3000A Series Bedienungsanleitung

GW Instek

GW Instek GPS-2303 Bedienungsanleitung

GW Instek

GW Instek SPS Series Bedienungsanleitung

GW Instek

GW Instek GPP-3650 Bedienungsanleitung

GW Instek

GW Instek SPS-1230 Bedienungsanleitung

GW Instek

GW Instek GCP-206P Bedienungsanleitung

GW Instek

GW Instek PSU Series Bedienungsanleitung

Beliebte Stromversorgung Handbücher anderer Marken

Monacor

Monacor PS-12CCD Bedienungsanleitung

VOLTIMA

VOLTIMA MagicBox 15 Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6032A Bedienungsanleitung

Miller

Miller Auto Deltaweld 452 Bedienungsanleitung

BCP

BCP PUOUBK Merkblatt

HC 2210 Bedienungsanleitung

Puls

Puls CT5.241 Bedienungsanleitung

OCZ

OCZ ZX1250W Bedienungsanleitung

iseg

iseg ECH 238 Bedienungsanleitung

Power

Power XXL A Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies 6631B Bedienungsanleitung

Renogy

Renogy PHOENIX 300 Bedienungsanleitung

HP 6200B Service-Handbuch

Epson

Epson Stylus Scan 2500 Betriebsanleitung

Pulsar

Pulsar GREEN POWER CCTV PoE POE044816 Bedienungsanleitung

Puls

Puls MiniLine ML50.100 Bedienungsanleitung

Puls

Puls AS-Interface SLA4.100 Bedienungsanleitung

Kenwood

Kenwood PS-60 Bedienungsanleitung