Häfele miniLock Bedienungsanleitung
Electronic cam lock
INSTALLATION MANUAL
EN
www.hafele.com
•lockers •cabinets •boxes
2
EN
Installation
Overview
1. miniLock
2. M16x1,5mm Cylinder nut
3. Stop Cam
4.Cam 22mm Axle
5. Cam 38mm Axle
6. M4x10mm Cam Screw
7-9. Mounting Screws
Assembly will
be made in
locked position
2
14
5
7
8
9
6
3
7
8
9
0 - 5 mm covers 8mm
10 -12 mm
covers
16mm
16 -18 mm
covers
24mm
Cover thickness Screw size
5
18
Note: 5 mm measurement is for 18 mm..!
Half gap should be 1.50 mm
1,50
3
0.16”(4mm)
2.44”(62mm)
0.63”(16mm)
miniLock Outline
Cylinder Hole
Mounting
Template Upper Mounting
Screw Hole
4
EN
Mounting on Left & Right Door
RIGHT LEFT
Hinges on
outside of
door are on
the Right
Hinges on
outside of
door are on
the Left
Peg on stop cam
is on the right side
Peg on stop cam
is on the left side
Back View
Knob, rotates to the
right to open lock
Back View
Knob, rotates to the
left to open lock
View of the lock
in closed position
5
22 mm Axle cam 38 mm Axle cam
RECESSED COVER ASSEMBLY MEASUREMENTS
25
3
16
62
4
JOINT ERECT LOCK ASSEMBLY MEASUREMENTS
6
EN
OVERLAPPING / EXTERNAL COVER
ASSEMBLY MEASUREMENTS
Right cover on the body
Locker body
22 mm cam
27 mm
42 mm
62 mm
3 mm
4 mm
Hole
16 mm
Hole
7
Replacing existing lock:
1. Place mounting template centered on existing hole and mark
upper mounting screw hole.
2. Drill mounting screw hole.
3. Install lock using adaptor if necessary.
4. Thread nut on cylinder.
5. Install mounting screw
6. Tighten both nut and mounting screw.
7. Test operation of lock
New Install:
1. Place mounting template on door and mark upper mounting
screw hole and lower cylinder hole
2. Drill mounting screw hole and cylinder holes.
3. Continue steps 4-7 above
Note: Before drilling holes, make sure miniLock is positioned
with proper clearance for cam to work.
NOTE: Read instructions, set combination
and test lock BEFORE installing!
Max
(Nm)
2
8
EN
1. Pull the transparent “Remove to Start” tag coming out of bat-
tery cap at thebackof thelock and activate thelock.
2. Read theuser manual and apply password change and
opening/closing operations severaltimes before themounting
of the lock.
3. Before mounting of the lock, switch lockhandle to closing
position.
4. Make sure that there is no friction in the cabinet lids.If there is
a frictionin the cabinet lids,make the hinge adjustments and
make the cabinet lid operable.
5. Do not forget to place Stop Camdepending on the condition
of the right or left lid of your cabinet.
6. Do not over-tighten nuts or screws. The maximum torqueon
the cylinder screw is 2Nm.
7. Ensure that there is no friction between strike plate and the
cam.
8. Finally check the mounting screws, tighten theloose screws.
9. When placing the existing locks into place, if the cylinder hole
is big, use theadapter and do not over tighten the cylinder
nut. (max. 2Nm).
10.Check the cabinet lid hingeadjustment at least once a year.
Tighten loose screws.
WARNINGS FOR MOUNTING:
9
35
86,5
24 28
18
75,45 gr (*)
* Assembly set is not.
10
Andere Handbücher für miniLock
2
Inhaltsverzeichnis
Andere Häfele Sperren Handbücher
Häfele
Häfele HLS100 Bedienungsanleitung
Häfele
Häfele DL7900 Bedienungsanleitung
Häfele
Häfele miniLock Bedienungsanleitung
Häfele
Häfele EFL 30 Bedienungsanleitung
Häfele
Häfele Keya-Tronic 231.49.031 Betriebsanleitung
Häfele
Häfele DT 210 R2 Bedienungsanleitung
Häfele
Häfele miniLock II Bedienungsanleitung
Häfele
Häfele LockerLock LL 200 Bedienungsanleitung
Häfele
Häfele DT 600 Bedienungsanleitung
Häfele
Häfele LockerLock LL 200 Bedienungsanleitung
