H3C CR1606-F Bedienungsanleitung

Contents

Installing the router························································································1

Confirming installation preparations···················································································································1

Attaching slide rails and cage nuts to the rack···································································································1

Installing slide rails·····································································································································1

Installing cage nuts ····································································································································2

Installing cable management brackets and mounting brackets (for the CR16014-F router)······························3

Installing cable management brackets·······································································································3

Installing mounting brackets·······················································································································4

(Optional) Installing an air filter ··························································································································5

Installing an air filter for a CR16010-F router·····························································································5

Installing an air filter for a CR16010H-F/CR16010H-FA/a CR16018-F/CR16018-FA router·····················6

Installing an air filter for a CR16000-F router·····························································································8

Mounting the router in the rack ··························································································································9

Grounding the router··········································································································································9

Grounding the router with a grounding strip·······························································································9

Grounding the router through the PE wire of an AC power supply··························································10

Grounding the router through the RTN wire of a DC power supply ·························································11

Installing the router

This section describes the procedure for installing the router.

NOTE:

•

The chassis and component views in this section are for illustration only.

•Keep the packages of the router and components for future use.

Confirming installation preparations

Before you install the router, verify that:

•

You have read the chapter "Preparing for installation" carefully and the installation site meets all

the requirements.

•

A 19-inch rack is ready for use if you are to install the router in a rack. For how to install a rack,

see the rack installation guide.

•

The rack is sturdy and is reliably grounded.

•

No debris or obstacles exist inside or around the rack.

•

Make sure the rack has enough space to accommodate the router. As a best practice to

maintain the rack stability, install the router at the rack bottom. To mount multiple devices in a

rack, install the heavier devices at the bottom.

•

The total height of the devices to be installed is no higher than the available installation height of

the rack and enough clearance is reserved for cable routing.

•

The router is ready for installation and has been carried to a place near the rack and convenient

for moving.

Attaching slide rails and cage nuts to the rack

Installing slide rails

Before you mount the router in a rack, install slide rails on the rack. As a best practice, purchase slide

rails from H3C. Table 1 describes the slide rails available for the router. For information about

installing the slide rails, see the installation guide shipped with the slide rails.

If the rack has slide rails installed, skip this section.

IMPORTANT:

•

Select slide rails for the router based on the total chassis weight.

•

To rack-mount the CR16018-F router and CR16018-FArouter, reserve a 2 RU space between

the router (including slide rails) and the rack bottom.

Table 1 Slide rails available for the router

Router

model

Chassis

weight with

full

configuration

Available slide rails

Slide rail

model

Max.

load-bearing

capacity Adjustment range Occupied

space

CR1606-

F 76 kg (167.55 lb)

LSXM1BSR 450 kg (992.06 lb) 630 to 900 mm (24.80

to 35.43 in) 1 RU

LSTM1KSGD0 280 kg (617.28 lb) 300 to 500 mm (11.81

to 19.69 in) 2 RU

LSTM2KSGD0

360 kg (793.65 lb) 500 to 800 mm (19.69

to 31.50 in) 2 RU

CR1601

0-F (one

fan tray)

120 kg (264.55

lb)

LSXM1BSR 450 kg (992.06 lb) 630 to 900 mm (24.80

to 35.43 in) 1 RU

LSTM1KSGD0 280 kg (617.28 lb) 300 to 500 mm (11.81

to 19.69 in) 2 RU

LSTM2KSGD0

360 kg (793.65 lb) 500 to 800 mm (19.69

to 31.50 in) 2 RU

CR1601

0-F (two

fan

trays)

170 kg (374.78

lb)

LSXM1BSR 450 kg (992.06 lb) 630 to 900 mm (24.80

to 35.43 in) 1 RU

LSTM1KSGD0 280 kg (617.28 lb) 300 to 500 mm (11.81

to 19.69 in) 2 RU

LSTM2KSGD0

360 kg (793.65 lb) 500 to 800 mm (19.69

to 31.50 in) 2 RU

CR1601

4-F 174 kg (383.60

lb)

LSXM1BSR 450 kg (992.06 lb) 630 to 900 mm (24.80

to 35.43 in) 1 RU

LSTM1KSGD0 280 kg (617.28 lb) 300 to 500 mm (11.81

to 19.69 in) 2 RU

LSTM2KSGD0

360 kg (793.65 lb) 500 to 800 mm (19.69

to 31.50 in) 2 RU

CR1601

0H-F/CR

16010H-

245 kg (540.12

lb)

LSXM1BSR 450 kg (992.06 lb) 630 to 900 mm (24.80

to 35.43 in) 1 RU

LSTM1KSGD0 280 kg (617.28 lb) 300 to 500 mm (11.81

to 19.69 in) 2 RU

LSTM2KSGD0 360 kg (793.65 lb) 500 to 800 mm (19.69

to 31.50 in) 2 RU

CR1601

8-F/CR1

6018-FA

440 kg (970.02

lb)

LSXM1BSR 450 kg (992.06 lb) 630 to 900 mm (24.80

to 35.43 in) 1 RU

LSTM2KSGD0

360 kg (793.65 lb) 500 to 800 mm (19.69

to 31.50 in) 2 RU

Installing cage nuts

Before mounting the chassis in the rack, attach cage nuts to the front rack posts.

1. Align the bottom edge of a mounting bracket with the top flange of a slide rail. Then mark the

cage nut installation holes on the front rack post.

If the mounting brackets are already installed, you can use a pattern tool to record the

installation holes of the mounting brackets and mark the cage nut holes accordingly.

2. Install cage nuts into the marked square holes on the front rack posts.

Figure 1 Installing cage nuts (CR16014-F)

(1) Installation holes for cage nuts

Installing cable management brackets and

mounting brackets (for the CR16014-F router)

Before installing the CR16014-F router in the rack, install the cable management brackets and

mounting brackets shipped with the router. The cable management brackets and mounting brackets

for other models have been installed when shipped. Cable management brackets are used for

cabling the router, and mounting brackets are used for attaching the chassis to the rack.

Installing cable management brackets

Cable management brackets include signal cable management brackets and power cord

management brackets.

The CR16014-F router comes with the signal cable management brackets attached to the mounting

brackets. You need to install the power cord management bracket for the router.

To install the power cord management bracket:

1. Unpack the power cord management bracket.

2. Place the power cord management bracket against the chassis and align the mounting holes in

the bracket with the installation holes in the chassis.

3. Use screws to secure the power cord management bracket to the chassis.

Figure 2 Installing a power cord management bracket

Installing mounting brackets

Before installing the router in the rack, attach the mounting brackets to the chassis.

The left and right mounting brackets available for the router are labeled with L and R marks,

respectively.

To install the mounting brackets, face the front of the router, and attach the left and right mounting

brackets to the two sides of the router, as shown in Figure 3.

Figure 3 Installing the mounting brackets

(Optional) Installing an air filter

Air filters are optional components and include chassis air filters and cabinet air filters. The

applicable air filters vary by router model.

Air filter is an optional component for the router. If you have ordered an air filter, install it before

mounting the router in the rack.

•

CR16010-F—Use a chassis air filter, which is installed over the air inlet vents at the bottom front

of the chassis. Before installing an air filter, install the power cord management bracket for the

chassis.

•

CR16010H-F/CR16010H-FA/CR16018-F/CR16018-FA—Use a cabinet air filter, which is

attached to the interior side of the cabinet door.

•

Other models—Use a chassis air filter, which is installed at the left of the chassis.

Installing an air filter for a CR16010-F router

1. Place the air filter over the inlet vents at the front panel bottom, and then align the captive

screws on the air filter with the screw holes in the chassis.

2. Faster the captive screws.

Figure 4 Installing an air filter

Installing an air filter for a CR16010H-F/CR16010H-FA/a

CR16018-F/CR16018-FA router

To prevent dust for a CR16010H-F/CR16010H-FA/a CR16018-F/CR16018-FA router, install an air

filter on the cabinet. For a cabinet with a double-leaf door, cut the air filter into two halves based on

the door size and install the air filter on the two door leaves.

To install an air filter on a cabinet:

1. As shown in Figure 5, paste air filter securing strips along the edge of the interior side of the

cabinet door at a location 1 to 2 cm (0.39 to 0.79 in) away from the perforation holes. For a

large-area single-leaf door, attach more securing strips.

Figure 5 Attaching air filter securing strips

(1) Securing strip installation position on a single-leaf door

(2) Securing strip installation position on a double-leaf door

2. Press the air filter onto the securing strips to cover the entire cabinet door.

Figure 6 Pasting the air filter onto the securing strips

3. Cut off the excess parts at locations such as the door lock location.

Figure 7 Cutting off the excess parts

4. Press the air filter again to ensure that it is attached to the securing strips tightly.

Installing an air filter for a CR16000-F router

1. Place the air filter over the inlet vents on the left panel of the chassis, and then align the captive

screws on the air filter with the screw holes in the chassis.

2. Fasten the captive screws.

Figure 8 Installing an air filter

Mounting the router in the rack

WARNING

•

Do not hold the handle of a fan tray or power module,

air vents, or the handle on the real panel to

move the router. Doing so might cause equipment damage or even bodily injury.

•

The router is heavy. As a best practice, use a mechanical lift to move it.

•

After placing the router on the slide rails

, do not leave go of your hands immediately because this

might tip the router, damaging the router or even causing bodily injury.

This task requires a minimum of two people.

To mount the router in the rack:

1. Move the chassis to face the rear of the chassis towards the front of the rack.

2. Lift the router by using the handles or supporting the bottom of the chassis until the bottom of

the router is a little higher than the slide rails on the rack.

3. Place the router on the slide rails and slide the router along the slide rails until the mounting

brackets on the router touch the front rack posts.

4. Attach the chassis to the rack with mounting screws.

Figure 9 Installing the chassis in the rack

If the mounting holes in the mounting brackets cannot align with the cage nuts on the rack, verify that

the bottom edge of the slide rail aligns with the middle of the narrower metal area between holes and

that the cage nuts are installed in the correct holes.

Grounding the router

CAUTION:

Before

you use the router, connect the grounding cable correctly to guarantee lightning protection

and anti-interference of the router.

Grounding the router with a grounding strip

CAUTION:

•

Use the supplied grounding cable (yellow-green grounding cable).

•

Connect the grounding cable to the grounding system in the equipment room. Do not connect it

to a fire main or lightning rod.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere H3C Netzwerk-Router Handbücher

H3C

H3C SR6602-X1 Bedienungsanleitung

H3C

H3C CR16000-F Bedienungs- und Wartungshandbuch

H3C

H3C S3100 Series Bedienungsanleitung

H3C

H3C CR16000-F Bedienungsanleitung

H3C

H3C CR16000-M Bedienungs- und Wartungshandbuch

H3C

H3C SR6616 Bedienungsanleitung

H3C

H3C MSR Series Installationshandbuch

H3C

H3C SR6604 Bedienungsanleitung

H3C

H3C RA5100 Bedienungsanleitung

H3C

H3C SecPath L5000-S Bedienungs- und Wartungshandbuch

H3C

H3C LS-5100-16P-SI-OVS-H3 Kurzanleitung

H3C

H3C H3C S5600 Series Bedienungsanleitung

H3C

H3C MSR 5660 Gebrauchs- und Pflegehandbuch

H3C

H3C S3100-52P Bedienungsanleitung

H3C

H3C MSR Series Installationshandbuch

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C S5500-SI Series Bedienungsanleitung

H3C

H3C MSR830 Series Bedienungsanleitung

H3C

H3C S5500-EI series Bedienungsanleitung

H3C

H3C S3610 Series Bedienungsanleitung

H3C

H3C CR16000-F Bedienungsanleitung

H3C

H3C S5500-SI Series Bedienungsanleitung

H3C

H3C RA10 Bedienungs- und Wartungshandbuch

H3C

H3C S5560-HI Series Bedienungsanleitung

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung