H3C CR16000-F Bedienungsanleitung

H3C CR16000-F Routers

Comware 7 OAA Configuration Guide

New H3C Technologies Co., Ltd.

http://www.h3c.com.hk

Software version: CR16000-CMW710-R7655P05 or later

Document version: 6W100-20170825

No part of this manual may be reproduced or transmitted in any form or by any means without prior written

consent of New H3C Technologies Co., Ltd.

Trademarks

H3C, , H3CS, H3CIE, H3CNE,Aolynk, , H3Care, , IRF, NetPilot, Netflow, SecEngine,

SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies

Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners

Notice

The information in this document is subject to change without notice. Every effort has been made in the

preparation of this document to ensure accuracy of the contents, but all statements, information, and

recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface

This configuration guide describes OAA fundamentals and configuration. It describes how to

configure the H3C open application platform (OAP) module connected to your device to exchange

information between your device and the OAP module.

This preface includes the following topics about the documentation:

•Audience.

•Conventions

•Obtaining documentation

•Technical support

•Documentation feedback

Audience

This documentation is intended for:

•Network planners.

•Field technical support and servicing engineers.

•Network administrators working with the routers.

Conventions

The following information describes the conventions used in the documentation.

Command conventions

Convention Description

Boldface Bold text represents commands and keywords that you enter literally as shown.

Italic Italic text represents arguments that you replace with actual values.

[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

{ x | y | ... }

Braces enclose a set of required syntax choices separated by vertical bars, from which

you select one.

[ x | y | ... ]

Square brackets enclose a set of optional syntax choices separated by vertical bars,

from which you select one or none.

{ x | y | ... } *

Asterisk marked braces enclose a set of required syntax choices separated by vertical

bars, from which you select a minimum of one.

[ x | y | ... ] *

Asterisk marked square brackets enclose optional syntax choices separated by vertical

bars, from which you select one choice, multiple choices, or none.

&<1-n> The argument or keyword and argument combination before the ampersand (&) sign

can be entered 1 to n times.

# A line that starts with a pound (#) sign is comments.

GUI conventions

Convention Description

Boldface Window names, button names, field names, and menu items are in Boldface. For

Convention Description

example, the New Use

window opens; click O

> Multi-level menus are separated by angle brackets. For example, File > Create >

Folder.

Symbols

Convention Description

WARNING! An alert that calls attention to important information that if not understood or followed

can result in personal injury.

CAUTION: An alert that calls attention to important information that if not understood or followed

can result in data loss, data corruption, or damage to hardware or software.

IMPORTANT: An alert that calls attention to essential information.

NOTE: An alert that contains additional or supplementary information.

TIP: An alert that provides helpful information.

Network topology icons

Convention Description

Represents a generic network device, such as a router, switch, or firewall.

Represents a routing-capable device, such as a router or Layer 3 switch.

Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that

supports Layer 2 forwarding and other Layer 2 features.

Represents an access controller, a unified wired-WLAN module, or the access

controller engine on a unified wired-WLAN switch.

Represents an access point.

Wireless terminator unit.

Wireless terminator.

Represents a mesh access point.

Represents omnidirectional signals.

Represents directional signals.

Represents a security product, such as a firewall, UTM, multiservice security

gateway, or load balancing device.

Represents a security module, such as a firewall, load balancing, NetStream, SSL

VPN, IPS, or ACG module.



Examples provided in this document

Examples in this document might use devices that differ from your device in hardware model,

configuration, or software version. It is normal that the port numbers, sample output, screenshots,

and other information in the examples differ from what you have on your device.

Obtaining documentation

To access the most up-to-date H3C product documentation, go to the H3C website at

http://www.h3c.com.hk

To obtain information about installation, configuration, and maintenance, click

http://www.h3c.com.hk/Technical_Documents

To obtain software version information such as release notes, click

http://www.h3c.com.hk/Software_Download

Technical support

service@h3c.com

http://www.h3c.com.hk

Documentation feedback

You can e-mail your comments about product documentation to info@h3c.com.

We appreciate your comments.

Contents

Configuring the OAP module ······························································1

About OAP modules···················································································································1

Logging in to an OAP module·······································································································1

Logging in through the console port on the OAP module······························································1

Logging in through the management Ethernet port on the OAP module by using SSH························1

Logging in through the internal Ethernet interface on the OAP module by using SSH·························2

Logging in from the CLI of the device·······················································································2

Resetting OAP modules ··············································································································2

About resetting OAP modules ································································································2

Restrictions and guidelines····································································································2

Procedure··························································································································3

Configuring the OAP manager ····························································4

About OAP manager···················································································································4

OAP manager/client model····································································································4

OAP functions ····················································································································4

OAP manager timers············································································································5

Configuring the OAP manager······································································································5

Enabling OAP·····················································································································5

Setting the clock synchronization timer·····················································································5

Setting the client monitoring timer ···························································································5

Managing OAP clients·················································································································5

Restarting an OAP client·······································································································5

Shutting down an OAP client ·································································································6

Display and maintenance commands for OAP manager·····································································6

Index·····························································································7

Configuring the OAP module

About OAP modules

The Open Application Platform (OAP) is a hardware platform based on the OpenApplication

Architecture (OAA). OAP uses a manager/client model. The OAP client can be a network device or

an OAP module. An OAP module can be an expansion card installed in a network device or an

integrated part of a network device.

OAP modules have their own operating systems. You can log in to the operating system of an OAP

module to install features. For example, you can install security features and voice features on the

OAP module operating system to provide security and voice services for users.

OAP modules exchange data, status information, and control information with hosting devices

through internal interfaces.

OAP provides an open interface for third-party vendors to develop and integrate value-added

applications into H3C products.

Logging in to an OAP module

Logging in through the console port on the OAP module

1. Connect one end of the console cable to the serial port of the configuration terminal (for

example, a PC).

2. Connect the other end of the console cable to the console port of the OAP module.

3. Start the PC and run a terminal emulation program, such as HyperTerminal.

4. Select the COM connection mode and set the terminal parameters as follows:

{Bits per second—9600.

{Data bits—8.

{Parity check mode—None.

{Stop bits—1.

{Flow control—None.

5. Follow the OAP module user guide to log in to the operating system of the OAP module.

Logging in through the management Ethernet port on the

OAP module by using SSH

1. Connect the management Ethernet port of the OAP module to the network by using a network

cable.

2. Log in to the OAP module through the console port and enable the SSH server function on the

OAP module.

3. Assign an IP address to the management Ethernet port of the OAP module. Make sure the

management Ethernet port and the SSH client (an H3C device or a PC with SSHclient software)

can reach each other.

4. From the SSH client, establish an SSH connection to the IP address of the management

Ethernet port on the OAP module.

After the SSH connection is successfully established, you are logged in to the operating system of

the OAP module.

Logging in through the internal Ethernet interface on the OAP

module by using SSH

When installed in the expansion slot of a device, an OAP module can exchange information with the

device through internal interfaces, including a fast Ethernet interface.

To log in to the operating system of an OAP module through the internal Ethernet interface:

1. Connect the SSH client (for example, a PC) to the Ethernet port of the device by using a

network cable.

2. Log in to the OAP module through the console port and enable the SSH server function on the

OAP module.

3. Assign an IP address to the internal Ethernet interface on the OAP module. Make sure the PC

and the fast Ethernet interface on the OAP module can reach each other.

4. From the SSH client, establish an SSH connection to the IP address of the fast Ethernet

interface.

After the SSH connection is successfully established, you are logged in to the operating system of

the OAP module.

Logging in from the CLI of the device

From the CLI of the device, you can log in to the CLI of the OAP module. To return to the CLI of the

device, press Ctrl+K.

Perform the following task in user view:

Task Command

device.

In standalone mode:

oap connect slot slot-number

In IRF mode:

oap connect chassis chassis-number slot slot-number

Resetting OAP modules

About resetting OAP modules

You can reset an OAP module to restore it to normal operation in the following situations:

•The OAP module fails.

•The OAP module is not operating correctly. For example, the OAP module does not respond to

your operation.

Pressing the reset button of the OAP module has the same effect. The device can still identify and

control the OAP module after the module starts up again.

Restrictions and guidelines

Resetting an OAP module might cause a service outage.

To avoid service data loss, close the operating system of an OAP module before resetting the

module.

Procedure

Perform the following task in user view:

Task Command

Reset the OAP module.

In standalone mode:

oap reboot slot slot-number

In IRF mode:

oap reboot chassis chassis-number slot slot-number

Configuring the OAP manager

About OAP manager

The Open Application Platform (OAP) is a hardware platform based on the Open Application

Architecture (OAA). OAAallows products from different vendors to operate together to meet service

requirements.

OAP manager/client model

OAP uses a manager/client model.

•OAP manager—A feature integrated in the Comware system software.

•OAP client—Afeature that is integrated in the Comware system software of the device or in the

operating system of the OAP module.

Figure 1 OAA diagram

As shown in Figure 1, OAA includes the following components:

•Routing/switching component—Provides routing and switching services. This component is

the control center of the entire architecture and acts as the OAP manager.

•Standalone service component—Provides services to meet specific requirements.

•Interfacing component—Connects the standalone service component to the

routing/switching component and acts as the OAP client.

OAP is used for communication and cooperation between the routing/switching component and the

standalone service component.

You can install an OAP module in the device. For example, you can install an IDS/IPS OAP module

in the device to provide intrusion detection and protection services.

OAP functions

OAP provides the following functions:

•OAP clients register with and deregister from the OAP manager.

•The OAP manager assigns IDs to OAP clients to uniquely identify the clients.

•The OAP manager and an OAPclient exchange information to, for example, monitor each other

and synchronize the clock.

From the OAP manager, you can perform the following tasks:

•Restart OAP clients.

•Shut down OAP clients.

•Display OAP client information.

An OAP manager can manage up to 255 OAP clients.

Andere Handbücher für CR16000-F

Inhaltsverzeichnis

Andere H3C Netzwerk-Router Handbücher

H3C

H3C SR6600 Series Bedienungsanleitung

H3C

H3C MSR 5600 Bedienungsanleitung

H3C

H3C SR8803-F Bedienungsanleitung

H3C

H3C CR16000-F Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Installationshandbuch

H3C

H3C S1216 Bedienungsanleitung

H3C

H3C S3100-52P Bedienungsanleitung

H3C

H3C RA5100 Bedienungsanleitung

H3C

H3C SR8800-F Bedienungsanleitung

H3C

H3C MSR810 Bedienungsanleitung

H3C

H3C S12500CR Series Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Installationshandbuch

H3C

H3C CR1606-F Bedienungsanleitung

H3C

H3C MSR 30-16 Bedienungsanleitung

H3C

H3C CR16006-F Kurzanleitung

H3C

H3C MSR 3600 Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Bedienungsanleitung

H3C

H3C MSR 930 Bedienungsanleitung

H3C

H3C S12500R Series Anwendungshandbuch

H3C

H3C MSR3600-28-X1 Bedienungsanleitung

H3C

H3C MSR 5660 Gebrauchs- und Pflegehandbuch

H3C

H3C S3100-52P Bedienungsanleitung

H3C

H3C H3C S5600 Series Bedienungsanleitung

H3C

H3C SR6600 SPE-FWM Installationshandbuch

Beliebte Netzwerk-Router Handbücher anderer Marken

Allnet

Allnet ALL0333AU Bedienungsanleitung

HomeSeer

HomeSeer HT-SEL Bedienungsanleitung

Sercomm

Sercomm Genesis OC3505D Bedienungsanleitung

Billion

Billion BIPAC 5102 Series Bedienungsanleitung

TP-Link

TP-Link TD-8817 Bedienungsanleitung

Motorola

Motorola MR1900 Bedienungsanleitung

Digi

Digi IX14 Bedienungsanleitung

Cisco

Cisco NCS 540 Handbuch

XAVi

XAVi X8821e Bedienungsanleitung

BEC

BEC 6200WZL Bedienungsanleitung

MikroTik

MikroTik hAP ac3 Series Bedienungsanleitung

Korenix

Korenix JetNet 5428G Series Bedienungsanleitung

NETGEAR

NETGEAR FS526T - Switch Bedienungsanleitung

Automated Logic

Automated Logic ZN551 Betriebsanleitung

Cisco

Cisco ASR 1000 Series Bedienerhandbuch

EnGenius

EnGenius ESR-9710 Bedienungsanleitung

Cisco

Cisco 805 Series Bedienungs- und Sicherheitshinweise

LevelOne

LevelOne FBR-1416 Bedienungsanleitung