H3C WA2110-AG Bedienungsanleitung

H3C WA2110-AG WLAN Access Point

Quick Start

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

No part of this manual may be reproduced or transmitted in any form or by any means

without the prior written consent of Hangzhou H3C Technologies Co., Ltd.

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents.

However, the statements, information, and recommendations in this document do not

constitute a warranty of any kind, express or implied. Hangzhou H3C Technologies Co.,

Ltd. and its licensors shall not be liable for technical or editorial errors or omissions

contained herein.

Acknowledgments

H3C, , Aolynk,

, H3Care,

, TOP G, , IRF, NetPilot, Neocean,

NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA,

VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of

Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this guide are the property of their

respective owners.

Environmental protection

This product has been designed to comply with the environmental protection

requirements. The storage, use, and disposal of this product must meet the applicable

national laws and regulations.

Table of Contents

WA2110-AG quick start guide·································································································· 3

Prepare for installation ··················································································································3

Unpacking and inspection ·······································································································3

Installation tools ·······················································································································3

Checking the device before installation····················································································4

Attaching the antennas················································································································4

Connecting the access point to an access controller/unified switch ·······································4

Mounting the access point ···········································································································4

Mounting the access point on a wall or ceiling ··········································································4

Mounting the access point on a tabletop··················································································5

WA2110-AG quick start guide

This guide provides steps for basic hardware installation for the WA2110-AG access point.

Further information, such as optional installation and configuration procedures and

technical specifications about connections and power are available in the H3C

WA2110-AG WLAN Access Point Installation Guide.

The WA2110-AG is a managed wireless LAN access point designed for use with an H3C

WX series access controller/unified switch and requires only hardware installation. All

configurations for the access point take place on the access controller/unified switch.

Prepare for installation

H3C recommends that all installation and removal of the unit and its accessories be

carried out by qualified personnel. Read all of the safety and installation instructions

supplied with your device before installation and operation.

Unpacking and inspection

Before unpacking the AP, ensure that the package is not damaged and that it does not

show signs of water damage. When unpacking the contents, avoid excessive force.

The accessories vary with the models. For the exact contents of the package, refer to

the packing list. If the contents do not match the packing list, contact your H3C

representative.

If the package is found to be rusted or water soaked, stop unpacking and contact your

H3C representative immediately.

Installation tools

Collect the following tools before installation:

Mounting bracket and screws that come with the device

Electric screwdriver and Phillips screwdriver

One electric drill and 6 mm (0.24) drill bit

Checking the device before installation

Before mounting the WA2110-AG, connect it to the power adapter (if applicable) and

the Ethernet, and check the status of the LEDs to ensure that the WA2110-AG works

properly. In addition, record the MAC address of the access point for future use.

Attaching the antennas

Attach the antennas on to the antenna connectors on the access point and

hand-tighten them. After network startup, you may need to adjust the antennas to

fine-tune the coverage in your area. For best results, adjust the antennas so that they are

perpendicular with the floor or ceiling.

CAUTION:

Do not handle the antenna tips, especially after they are connected to the access point. This

can create electrostatic discharge (ESD) and damage the equipment.

Do not touch or remove the access point when its antenna is receiving or transmitting radio

frequency signals.

Connecting the access point to an access

controller/unified switch

H3C recommends installing and configuring the access controller/unified switch before

installing the access point. This is to ensure that you can verify whether the access point

works normally immediately after you connect it. For instructions on configuring the

access controller or unified switch, see H3C WX Series Access Controllers User Manual

and H3C WX Series Access Controllers Web-Based Configuration Manual.

Connect the access point to an access controller/unified switch directly or indirectly

through an intermediate Layer 2 or Layer 3 network. In either case, use a Category 5e

cable for the connection.

Mounting the access point

You can mount the access point on a wall, ceiling, or table top.

Mounting the access point on a wall or ceiling

To mount the access point to a wall or ceiling:

CAUTION:

For easy installation and removal of the access point from the mounting bracket, ensure that

there is sufficient flexibility with the cable and that the cable is long enough. H3C recommends

using flexible cables. If not enough cable is routed through the back of the mounting bracket,

or the cable is inflexible, it can be difficult to install or remove the access point from the

mounting bracket.

1. Remove the access point from the mounting bracket.

2. Route the Ethernet cable and, if you are using a power adapter, the power cable

on the back of the mounting bracket.

3. Mount the bracket to a wall or ceiling.

4. Connect the Ethernet cable and the power cable (if using a power adapter) to the

corresponding port(s) on the access point.

CAUTION:

To avoid connection interference caused by dust, clean the pins of the cable connector

before connecting the cable to the access point.

Discharge the cable before connecting it to the access point.

WARNING:

In case of lightning, do not plug/unplug the cable to/from the access point.

When the LEDs of the access point are blinking, do not plug/unplug the cable to/from the

access point or perform any operation that may affect the normal running of the access point.

5. Align the bottom of the access point with the mounting bracket, and press against

the access point until it is securely mounted in the mounting bracket. To avoid

physical damage to the access point, do not use excessive force when mounting

or unmounting the access point.

6. To prevent theft of the access point, insert the locking bar into the opening at one

side of the mounting bracket. Push the locking bar through the opening until the

hole on the locking bar is exposed. Insert the shackle of a lock through the hole on

the locking bar to lock the access point to the mounting bracket.

Mounting the access point on a tabletop

To install the access point on a flat surface such as a table or desktop:

WARNING:

When the RF antennas are transmitting data, keep the antennas away from your face, eyes,

and other exposed parts of your body.

Do not mount the access point on any metal surface.

Do not use or manipulate the access point near explosives unless otherwise

authorized by relevant authorities. Remove the access point from the mounting

bracket and place it on the table in a position with good signal coverage.

Place the access point on the table. Connect the Ethernet cable and power cable

(if you are using a power adapter) to the corresponding port(s) on the access point.

Andere Handbücher für WA2110-AG

Inhaltsverzeichnis

Andere H3C Drahtloser Zugangspunkt Handbücher

H3C

H3C 6W100 Bedienungsanleitung

H3C

H3C WA6120 Bedienungsanleitung

H3C

H3C WA2110-AG Bedienungsanleitung

H3C

H3C WA2210-AG_INDOORSINGLEBANDAP Bedienungsanleitung

H3C

H3C WA4320H-ACN Bedienungsanleitung

H3C

H3C WA6528X-E Bedienungsanleitung

H3C

H3C WA2620X-AGNP Bedienungsanleitung

H3C

H3C WA Series Installationshandbuch

H3C

H3C WA6638 Bedienungsanleitung

H3C

H3C WA5320 Bedienungsanleitung

H3C

H3C WA6320H-HI Bedienungsanleitung

H3C

H3C WA6500 Series Benutzerhandbuch

H3C

H3C WA Series Bedienungsanleitung

H3C

H3C WA5320X Bedienungsanleitung

H3C

H3C WA2600 Series Bedienungsanleitung

H3C

H3C WA6636 Bedienungsanleitung

H3C

H3C WA6120X Bedienungsanleitung

H3C

H3C WA4320-ACN-PI Bedienungsanleitung

H3C

H3C WX6600 Series Bedienungsanleitung

H3C

H3C WA4320i-ACN Bedienungsanleitung

H3C

H3C WA2612-AGN Bedienungsanleitung

H3C

H3C WA6330 Bedienungsanleitung

H3C

H3C WA6520H Bedienungsanleitung

H3C

H3C WA2620-AGN Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung