H3C WA2600 Series Bedienungsanleitung

H3C WA2600 Enhanced Series

WLAN Access Points Quick Start Guide

Abstract

This document details the installation procedure for the WA2600 series enhanced WLAN access

points.

Hangzhou H3C Technologies Co., Ltd.

http://www.h3c.com

No part of this manual may be reproduced or transmitted in any form or by any means

without the prior written consent of Hangzhou H3C Technologies Co., Ltd.

The information in this document is subject to change without notice. Every effort has

been made in the preparation of this document to ensure accuracy of the contents.

However, the statements, information, and recommendations in this document do not

constitute a warranty of any kind, express or implied. Hangzhou H3C Technologies Co.,

Ltd. and its licensors shall not be liable for technical or editorial errors or omissions

contained herein.

Acknowledgments

H3C, , Aolynk,

, H3Care,

, TOP G, , IRF, NetPilot, Neocean,

NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA,

VVG, V2G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of

Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this guide are the property of their

respective owners.

Environmental protection

This product has been designed to comply with the environmental protection

requirements. The storage, use, and disposal of this product must meet the applicable

national laws and regulations.

Table of Contents

WA2600 enhanced series APs quick start guide ········································································· 3

Installation preparations················································································································3

Unpacking and inspection ·······································································································3

Installation tools ·······················································································································4

Installation site examination······································································································4

AP Installation ······························································································································5

Determining the installation position··························································································5

Installing the wall-mounting bracket on the wall·········································································5

Installing the AP on the wall-mounting bracket ··········································································5

Optional: Locking the AP onto the wall-mounting bracket ··························································6

Connecting the power supply·······································································································7

Local power supply··················································································································7

Power over Ethernet (PoE)········································································································7

Connecting the AP to the network ································································································7

WA2600 enhanced series APs quick

start guide

This guide provides steps for basic installation for the WA2600 enhanced series access

points. Further information, such as optional installation and configuration procedures

and technical specifications about connections and power is available in the H3C

WA2600 Enhanced Series Access Point Installation Guide.

Installation preparations

This chapter describes the preparations for WA2600 enhanced series installation,

including unpacking and inspection of the product, preparation of installation tools, and

choosing the location site.

WARNING!

H3C recommends that installation and removal of the unit and its accessories be carried out by

qualified personnel. Read all of the safety and installation instructions supplied with your device

before installation and operation.

Unpacking and inspection

Before unpacking the product, ensure that the package is not damaged and that it

does not show signs of water damage. When unpacking the package, avoid excessive

force.

The accessories vary with the models. For the exact contents of the package, refer to

the packing list. If the contents do not match the packing list, contact your H3C

representative.

If the package is found to be rusted or water soaked, stop unpacking and contact your

H3C representative immediately.

Installation tools

When installing the AP, you may need some of the tools listed in Table 1 . Choose the

appropriate tools according to your installation environment.

Table 1 List of installation tools

Tool Type

Tool

General tools

1-meter-long ruler, marking pen, knife, and

a percussion drill with a 6mm (0.24 in)( bit

Special tools

Cable strippers, crimping pliers, and RJ-45

crimping pliers

Auxiliary tools

Ladder and rubber hammer

Installation site examination

Before installation, examine the installation site from the following aspects: temperature

and humidity requirements, power supply, and grounding and lightning protection. For

these requirements, see the H3C WA2600 Enhanced Series Access Point Installation

Guide. For details about temperature and humidity requirements, power supply, and grounding

and lightning protection, see the

H3C WA2600 Enhanced Series WLAN Access Point Installation

Guide

After you have completed the installation preparations, continue with AP installation.

AP Installation

The WA2600 enhanced series WLAN APs can be directly affixed onto a wall by using the

wall-mounting brackets. This section contains the wall-mounting procedure for the

WA2600 enhanced series.

Determining the installation position

Determine the installation position by observing the following:

Leave as few obstacles (such as wall and ceiling) as possible between the AP and

the wireless stations.

Keep the AP far away from electronic devices (such as microwave ovens) that may

generate RF noise.

Install the AP in a place where it will not hinder people’s daily work and life.

Ensure the ceiling is strong enough and the structure is suitable when using ceiling

mounting. Reinforce the ceiling if needed. A padlock is required for ceiling

mounting to prevent falloff due to shock or vibration.

Installing the wall-mounting bracket on the wall

1. There are eight installation holes in the wall-mounting bracket. Use at least four of

them for the installation. Measure and mark the wall where the AP would be

mounted. Ensure holes correspond to those in the bracket. Using a precision drill

with a 6 mm (0.24 in) bit, drill holes on the markings. The arrowhead on the bracket

should point upward.

2. Insert the pointed end of anchors into the drilled holes and tap the flat end of

anchors with a rubber hammer until they are all flush with the wall surface.

3. Align the holes in the wall-mounting bracket with the anchors and insert screws

through the installation holes into the anchors.

4. Adjust the position of the wall-mounting bracket as necessary, and tighten the

screws.

Installing the AP on the wall-mounting bracket

The installation procedure is the same for both the WA2610E-AGN and WA2620E-AGN.

The WA2610E-AGN is used as an example in this guide.

1. Align the AP with the hooks on the wall-mounting bracket and hang the AP on the

bracket. See (1) in Figure 1 .

2. Press the AP downward to affix it. See (2) in Figure 1 .

Figure 1 Fix the AP onto the wall-mounting bracket

(1)

(2)

Expansion

scerw

Hook

Optional: Locking the AP onto the wall-mounting bracket

The WA2600 enhanced series APs have a security slot on the top, which can be used to

lock the AP onto the wall-mounting bracket to prevent theft. For details, see the H3C

WA2600 Enhanced Series Access Point Installation Guide. A lock is user-supplied.

Connecting the power supply

Local power supply

Connect the AP to the power source through the power adapter.

Power over Ethernet (PoE)

If the uplink device of the AP is a PoE-capable switch, use an Ethernet cable to connect

the Ethernet interface of the AP to the PoE-capable device.

CAUTION:

In the PoE mode, you do not need to connect the power interface to a power source. You

only need to connect one end of an Ethernet cable to the Ethernet interface of the AP and

the other end to an Ethernet interface of the PoE-capable device (for example, an Ethernet

switch).

Identify the silkscreen on the device to avoid confusing the console interface for the Ethernet

interface and vice versa.

The WA2620E-AGN supports only non-standard PoE power supply (the PoE input power must

be at least 16W).

Connecting the AP to the network

The WA2600 enhanced series can access the Internet or metropolitan area network

(MAN) through the Ethernet uplink interface. Connect the Ethernet interface of the AP

to an Ethernet interface of an Ethernet switch to implement Internet or MAN access.

For details on configuring your AP (work in fat mode), see the H3C WA Series WLAN

Access Points Configuration Guides, H3C WA Series WLAN Access Points Command

References, and H3C WA Series WLAN Access Points Web-Based User Guides on our

website:

http://www.h3c.com

Andere Handbücher für WA2600 Series

Inhaltsverzeichnis

Andere H3C Drahtloser Zugangspunkt Handbücher

H3C

H3C WA2620X-AGNP Bedienungsanleitung

H3C

H3C WA Series Bedienungsanleitung

H3C

H3C WA6622 Bedienungsanleitung

H3C

H3C WA560 Bedienungsanleitung

H3C

H3C WA5320X Bedienungsanleitung

H3C

H3C WA2210-AG_INDOORSINGLEBANDAP Bedienungsanleitung

H3C

H3C WA6628E-T Bedienungsanleitung

H3C

H3C WA6628 Bedienungsanleitung

H3C

H3C WA510H Bedienungsanleitung

H3C

H3C WA6120X Bedienungsanleitung

H3C

H3C WA6500 Series Benutzerhandbuch

H3C

H3C 6W100 Bedienungsanleitung

H3C

H3C WA4600 Series Bedienungsanleitung

H3C

H3C WA2200 Series Bedienungsanleitung

H3C

H3C WA Series Bedienungsanleitung

H3C

H3C WA4600 Series Bedienungsanleitung

H3C

H3C WA2200 Series Bedienungsanleitung

H3C

H3C WA Series Installationshandbuch

H3C

H3C WA6620X Bedienungsanleitung

H3C

H3C WA6320H-HI Bedienungsanleitung

H3C

H3C WA538 Bedienungsanleitung

H3C

H3C WA5320 Bedienungsanleitung

H3C

H3C WA6636 Bedienungsanleitung

H3C

H3C WA6630X Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung