Haier CRDE400AW Bedienungsanleitung

Model # RDE400AW/R,RDE200AW,CRDE400AW/R,CRDE200AW

Cycles

Very

Damp

Dry

Cooldown

Cyclecompleted

Extendtrumble

Louder

Softer

Off

Cycle

Signal

PermanentPress

Off

Wrinkle

Care

Timed

Cycles

MoreTime

LessTime

AutoDry

TimedDry

TimeRemaining

On/Off

Power

Pause

Start

Temp

Level

Dryness

AirOnly(NoHeat)

High

Medium

Low

Electric Dryer

Seche-linge Genesis

Secadora Electrica

User Manual

Modele # RDE400AW/R,RDE200AW,CRDE400AW/R,CRDE200AW

Guide de l Utilisateur

Para Modelo de # RDE400AW/R,RDE200AW,CRDE400AW/R,CRDE200AW

Guide del Usuario

Delicate

Normal

Less

Heavy

Cotton

Costomized

BulkyItems

RackDry

Quality Innovationg Style

2. Do not dry articles that have been previously cleaned in,washed in,

soaked in,or spotted with gasoline, dry-cleaning solvents, or other

flammable or explosive substances, as they give off vapors that

could ignite or explode.

3. Do not allow children to play on or in the appliance. Close

supervision

of children is necessary when the appliance is used near

children.

4. Before the appliance is removed from service or discarded, remove the

door to the drying compartment.

5. Do not reach into the appliance if the drum is moving.

6. Do not install or store this appliance where it will be exposed to water

And/or to the weather.

8. Do not repair or replace any part of the appliance or attempt any

servicing unless specifically recommended in the user-repair

instructions that you understand

and have skills to carry out.

9. Do not use fabric softeners or products to eliminate static unless

recommended by the manufacturer of the fabric softener or

product.

10. Do not usefabric softeners or products to eliminate static unless

recommended by the manufacturers of the fabric softener or

product

11.Clean lint screen before or after each load.

12.Keep area around the exhaust opening and adjacent surrounding

areas free from the accumulation of lint, dust and dirt.

13.The interior of the appliance and the exhaust duct should be cleaned

periodically by qualified service personnel.

14.Do not place items exposed to cooking oils in your dryer. Items

contaminated with cooking oils may contribute to a chemical

reaction that could cause a load to catch fire

15.If material has been used with any flammable liquids or solids, it

should

not used in the dryer until all traces of the flammable liquids

and its fumes have been removed.

English

7. Do not tamper with controls.

16. This dryer must be properly installed in accordance with the

installation instructions before it is used. See grounding instructions

in the installations sections.

17. Proper grounding must be ensured to reduce the risk of electric shock

and force. Check with a qualified electrician or service personnel if

you

are in doubt as to whether the dryer is properly grounded.

18. Use the dryer only for its intended purpose, drying clothes.

19. Always disconnect dryer from electrical supply before attempting any

service. Disconnet power cord by grasping the plug,not the cord.

20. Replace worn power cords and/or loose plugs.

21. To reduce the risk of electric shock or fire, do not use extension cords or

adapters to connect dryer to electrical power source.

English

product. This easy-to-use manual

will guide you in getting the best

use of your dryer.

Thank you for using our Haier

Remember to record the model and

serial number. They are on a label

in back of the dryer.

Model number

Serial number

Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

Tables Of Contents

PAGE

Safety Instructions

............................................................................

OPERATING INSTRUCTIONS

............................................................

13-22

..........................................................

Other Features

.................................................................................

Normal Operating Sounds

.................................................................

Tips

.................................................................................................

Care and Cleaning Guide

...............................................................

Troubleshooting

..............................................................................

INSTALLATION INSTRUCTIONS

.......................................................

4-12

Tools and Materials Required

..............................................................

Electrical Requirements

......................................................................

Unpacking Your Dryer

........................................................................

Exhaust System Connections

..........................................................

Requirements and Instructions

............................................................

Materials

............................................................................................

Location of Your Dryer

........................................................................

Installation in Mobile Home

...............................................................

Electrical Connections

....................................................................

Requirements and Instructions

.............................................................

3-Wire Cord Connections

...................................................................

4-Wire Cord Connections........................................................................................

11-12

Understanding the Control Panel

Auto Dry cycle

Timed Dry cycle

Rack Dry cycle

.................................................................................

...................................................................................

16-18

......................................................................

Load clothes into dryer

..................................................................

Preparations before drying

English

WARRANTY

..............................................................................

INSTALLATION INSTRUCTIONS

Phillips head and flathead screwdrivers

Channel-lock adjustable pliers

1/2 inch open end wrench

Carpenter s level

Measuring tape (12ft. Min.)

Duct tape

Rigid or flexible metal 4 inch (10.2 cm) duct

Vent hood

1. Remove all packaging material. This includes the foam base and all adhesive

tape holding the dryer accessories inside and outside.

2. Inspect and remove any remains of packaging, tape or printed

materials before using the dryer.

Tools and Materials Required

Electrical Requirements

Unpacking Your Dryer

English

Select a suitable location for the dryer on a hard even surface away from

direct sunlight or heat sources, baseboardheaters, cooking appliances etc.

Any floor unevenness should be corrected with leveling legs located on the

bottom of the dryer.

U.S. Only

Power supply:

3 or 4 wire,240 Volt, 30Amp,60Hz, 1 Phase Power Supply Cord Kit (not

supplied when sold in the United States) – Purchase to meet local electrical codes.

The dryer MUST employ a 3-conductor power supply cord NEMA 10-30 Type

SPDT RATED AT 240 Volt AC minimum, 30 Amp.,with 3 open end spade lug

connectors with upturned ends or closed loop connectors and marked for use with

clothes dryers. If being installed ina manufactured (mobile) home,thedryer MUST

employ a 4-conductor power supply cord. NEMA 14-30 type SRDT or ST (as

required) rated at 240 Volt AC Minimum, 30 Amp., with 4 open end spade lug

connectors with upturned ends or closed loop connectors and marked for use with

clothes dryers. See Electrical Connections for A 4-Wire System.

Canada. Only

Candian models are supplied with the appropriate power cord.

Exhaust System Connections

Requirements and Instructions

1. Do not use plastic flexible duct to exhaustthe dryer. Excessive lint can build up

inside system and create a fire hazard and restrict air flow. Restricted airexhaust

flow will increase dryer times. If your present system is made up of plastic duct or

metal foil duct, replace it with a rigid or flexible metal duct. Ensure present duct

is free of any lint prior to installing dryer duct.

2. If the dryer is not exhausted out doors, some fine lint will be expelled

into the laundry area. An accumulation of lint in any area of the home can

create a health and fire hazard. To reduce risk of fire, dryer MUST BE

EXHAUSTED OUTDOORS.

3. Do not allow combustible material (for example: clothing,

draperies/curtains, paper) to come in contact with venting system. The dryer

must not be exhausted into a chimney, a wall, a ceiling, or any concealed space

of a building which can accumulate lint, resulting in a fire hazard.

4. Exceeding the length of duct pipe or number of elbows allowed in

the "Maximum Length" charts can cause an accumulation of lint in

the exhaust system. Plugging the system could create a fire hazard,

as well as increase drying times.

5. Do not screen the exhaust ends of the vent system, nor use any screws

or rivets to assemble the exhaust system. Lint can become caught in the screen,

on the screws or rivets, clogging the duct work and creating a fire hazard as well

as increasing drying times. Use an approved vent hood to terminate the duct out-

doors, and seal all joints with duct tape. All male duct pipe fittings must be

installed downstream with the flow of air.

Explosion hazard:

Do not install the dryer where gasoline or other flammables are kept or stored.

If the dryer is installed in a garage, it must be minimum of 18 inches (45.7 cm)

above the floor. Failure to do so can result in death, explosion, fire or burns.

English

Materials

English

Although vertical orientationof the exhaust system isacceptable. Certain

extenuating circumstances could affect the performance of the dryer:

1. Only rigid metal duct work should be used.

2. Ventingvertically through aroof may expose the exhaust system to down

drafts causing an increase in vent restriction.

3. Running the exhaust system through an area not insulated may cause

condensation and faster accumulation of lint.

4. Compression of crimping of the exhaust system will cause an increase in vent

restriction.

The exhaust system should be inspected and cleaned a minimum of every 12

months with normal usage. The more the dryer is used the more often you should

check the exhaust system and vent hood for proper operation.

Use only 4 inch (10.2cm) diameter (minimum) rigid of flexible metal duct and

approved vent hood which has a swing-out damper hat open when the dryer is

in operation. When the dryer stops, the dampers automatically close to prevent

drafts and the entrance of insects and rodents. To avoidrestricting the outlet,

maintain a minimum of 12 inches (30.5cm) clearance between the vent hood and

the ground or any other obstruction. The vent flap should be able to move freely.

Do Not Install Your Dryer:

In an area exposed to dripping water or outside weather conditions.

In an area where it will come in contact with curtains, thick carpet,

or anything that will obstruct the flow of combustion and ventilation air.

On carpet. Floor must be solid with a maximum slope of 1inch (2.54 cm).

Location of Your Dryer

English

Dryer must be exhausted outside (outdoors, not beneath the mobile home)

using metal ducting that will not support combustion. Metal ducting must be

4 inches (10.16 cm) in diameter with no obstructions. Rigid metal duct is

preferred.

If dryer is exhausted through the floor and area beneath the mobile home is

enclosed, the exhaust system must terminate outside the enclosure with the

termination securely fastened to the mobile home structure.

Refer to previous pages for other important venting requirements.

Installation must conform to current Manufactured Home Construction &

Safety Standard.

Installation in Mobile Home

Correct Incorrect

English

Electrical Connections

Requirements and Instructions

1. This appliance must be properly grounded. Electrical shock can result if the

dryer is not properly grounded. Follow the instructions in this manual for

Proper grounding.

2. Do not use an extension cord with this dryer. Some extension cords are not

designed to withstand the amounts of electrical current this dryer utilizes and

can melt, creating electric shock and/or fire hazard. Locate the dryer within

reach of the receptacle for the length power cable to be purchased, allowing

Some slack in the cord. Refer to the electrical requirements in this manual for

The proper power cord to be purchased.

3. A UL approve strain relief must be installed onto power cable. If the the strain

relief is not attached, the cord can be pulled out of the pulled out of the

dryer and can be cut by any movement of the cord, resulting in electrical

shock.

4. Do not use an aluminum wire receptacle with copper wired power cord and

plug (or vice versa). A chemical reaction occurs between copper and

aluminum and can cause electrical shorts. The proper wiring and receptacle

is a copper wired power cord with a copper wired receptacle.

Danger: Improper connection of the equipment grounding conductor can

result in a risk of electrical shock. Check with a licensed

electrician if you are in doubt as to whether the appliance is

properly grounded.

English

Note: Dryers operating on 208 Volt power supply sill have longer drying times

than operation on240 Voltpower supply.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Haier Trockner Handbücher

Haier

Haier HMS6-1 Bedienungsanleitung

Haier

Haier HDM3.5-1 Bedienungsanleitung

Haier

Haier HD90-A2979 Bedienungsanleitung

Haier

Haier HDY-C70 ME Bedienungsanleitung

Haier

Haier HWS60-40 Bedienungsanleitung

Haier

Haier HD80-26A Bedienungsanleitung

Haier

Haier GDZ3.5-1-HK Bedienungsanleitung

Haier

Haier HLF11PC Bedienungsanleitung

Haier

Haier HD80-01 WH HA AA Bedienungsanleitung

Haier

Haier GDZ5.0-61WH HA AA Bedienungsanleitung

Haier

Haier Genesis CGDE700AW Bedienungsanleitung

Haier

Haier HDY6-1 Bedienungsanleitung

Haier

Haier HLP140E - 2.6 cu. Ft. Portable Vented Electric... Bedienungsanleitung

Haier

Haier HD80-A2939 Bedienungsanleitung

Haier

Haier HD80-26A Bedienungsanleitung

Haier

Haier HD80-A3939E-S Bedienungsanleitung

Haier

Haier HD90-A2979 Bedienungsanleitung

Haier

Haier HLTD500ACW Bedienungsanleitung

Haier

Haier HLF11PC Bedienungsanleitung

Haier

Haier LDS7HC Bedienungsanleitung

Haier

Haier GDZ5-1 Bedienungsanleitung

Haier

Haier HDHP80AW1 Bedienungsanleitung

Haier

Haier HLP140E - 2.6 cu. Ft. Portable Vented Electric... Bedienungsanleitung

Haier

Haier HD80-B636-F Bedienungsanleitung

Beliebte Trockner Handbücher anderer Marken

Bosch

Bosch WTA79200GB Bedienungsanleitung

Amana

Amana W10233410A Bedienungsanleitung

Miele

Miele TWH 780 WP Bedienungsanleitung

Asko

Asko T760 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems 25 Series Bedienungsanleitung

Bosch

Bosch Logixx 10 WTB76556GB Technisches Datenblatt

STIEBEL ELTRON

STIEBEL ELTRON Ultronic S Bedienungsanleitung

Electrolux

Electrolux EW2H328R2 Bedienungsanleitung

Beko

Beko DS8433RX1M Bedienungsanleitung

Dawlance

Dawlance Spinner DS 6000 C Bedienungsanleitung

Electrolux

Electrolux TP5080TW Bedienungsanleitung

AEG

AEG TR838P4OB Bedienungsanleitung

Indesit

Indesit IDV 75 Bedienungsanleitung

Infiniton

Infiniton SD-DG85C Bedienungsanleitung

BOMANN

BOMANN WT 5019 Bedienungsanleitung

Alliance Laundry Systems

Alliance Laundry Systems TMB795C Bedienungsanleitung

Asko

Asko T793C Bedienungsanleitung

Kenmore

Kenmore 8041 - 5.8 cu. Ft. Capacity Electric Dryer Bedienungsanleitung