Hakko Electronics FR-4103 Bedienungsanleitung

Table of Contents

............................ 1

....................................................... 1

....................... 2

............................................................ 3

................................................................ 4

............................................ 13

........................................................ 22

........................................ 27

................................................... 29

................................. 30

............................................................... 31

................................................... 34

1. PACKING LIST AND PART NAMES

2. SPECIFICATIONS

3. WARNINGS, CAUTIONS AND NOTES

4. INITIAL SETUP

5. OPERATION

6. PARAMETER SETTING

7. MAINTENANCE

8. CHECKING PROCEDURE

9. ERROR MESSAGE

10. TROUBLE SHOOTING GUIDE

11. PARTS LIST

12. WIRING DIAGRAM

ThankyouforpurchasingtheHAKKOFR-410DesolderingTool.

Thisproductisadesolderingtoolthatusesthequick-changemechanism.

PleasereadthismanualbeforeoperatingtheHAKKOFR-410.

Keepthismanualreadilyaccessibleforreference.

(HAKKO FR-4103)

Instruction Manual

DESOLDERING TOOL

FR-410

Cleaning Pin (for ø1.0 mm

[0.04 in] nozzle)

Nozzle wrench

Ceramic paper Filter

(for handpiece)

Filter

(for station) Cleaning Pin

(for heating element)

Cleaning Drill (for ø1.0 mm

[0.04 in] nozzle)

HAKKO FH-410

Power cord

Tool box

HAKKO

FR-410

×1

×2×4

HAKKO FR-410 station

HAKKO FR-4103 handpiece

(with N61-05 (ø1.0 mm [0.04 in] type S) nozzle)

Power cord

HAKKO FH-410 iron holder

(with cleaning sponge)

Tool box

Instruction Manual

2. SPECIFICATIONS

● HAKKO FR-410

Power consumption

Temperature range

Temperature stability

190 W

330 - 450℃(620 - 850℉)

±5℃(±9℉) at idle temperature

● Station

Output

Vacuum generator

Vacuum pressure (max.)

Suction flow

Dimensions

Weight

AC 24 V

Vacuum pump, double cylinder type

80 kPa (600 mmHg)

15 L/min.

165 (W) × 137 (H) × 244 (D) mm

(6.5 × 5.4 × 9.6 in.)

4.8 kg (10.6 lb.)

●Handpiece (HAKKO FR-4103)

Part name

Power consumption

Nozzle to ground resistance

Nozzle to ground potential

Cord

Length (w/o cord)

Weight (w/o cord)

HAKKO FR-4103

140 W (24 V)

<2 Ω

<2 mV

1.2 m (4 ft.)

168 mm (6.6 in.) with N61-05 nozzle

190 g (0.42 lb.) with N61-05 nozzle

* The temperature was measured using the HAKKO FG-101

Soldering Tester.

* This product is protected against electrostatic discharge.

* Specifications and design are subject to change without notice.

1. PACKING LIST AND PART NAMES Please check to make sure that all items

listed below are included in the package.

Nozzle (N61 series)

Filter pipe

Trigger

HAKKO FR-4103

CAUTION

■ Electrostatic Protection

3. WARNINGS, CAUTIONS AND NOTES

WARNING

CAUTION

To prevent accidents or damage to the HAKKO FR-410, be sure to observe the following:

● Do not use the unit for applications other than desoldering.

● Do not strike the handpiece against hard objects to remove excess solder. This will

damage the handpiece.

● Do not modify the HAKKO FR-410.

● Use only genuine HAKKO replacement parts.

● Do not allow the HAKKO FR-410 to become wet, or use it when hands are wet.

●

Be sure to hold the plug when inserting or removing the handpiece and power cords.

● Be sure the work area is well ventilated. Desoldering produces smoke.

● While using the HAKKO FR-410, don't do anything which may cause bodily harm

or physical damage.

When power is ON, the nozzle will be hot. To avoid injury or damage to

personnel and items in the work area, observe the following:

● Donottouchthenozzleorthemetalpartsnearthenozzle.

●

Donotallowthenozzletocomecloseto,ortouch,ﬂammablematerials.

●

Informothersintheareathattheunitishotandshouldnotbetouched.

● Turnthepoweroﬀwhennotinuse,orleftunattended.

● TurnthepoweroﬀwhenchangingpartsorstoringtheHAKKO

FR-410.

● Thisunitisforcounterorworkbenchuseonly.

●

This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in safe way and

understand the hazards involved.

● Children shall not play with the appliance.

●

Cleaning and user maintenance shall not be made by children

without supervision.

Warnings, cautions and notes are placed at critical points in this manual to direct the

operator’s attention to significant items. They are defined as follows:

W A R N I N G：FailuretocomplywithaWARNINGmayresultinseriousinjuryordeath.

CAUTION：FailuretocomplywithaCAUTIONmayresultininjurytotheoperator,

ordamagetotheitemsinvolved.



N O T E：ANOTEindicatesaprocedureorpointthatisimportanttotheprocess

beingdescribed.

Cleaning Pin (for ø1.0 mm

[0.04 in] nozzle)

Nozzle wrench

Ceramic paper Filter

(for handpiece)

Filter

(for station) Cleaning Pin

(for heating element)

Cleaning Drill (for ø1.0 mm

[0.04 in] nozzle)

HAKKO FH-410

Power cord

Tool box

HAKKO

FR-410

×1

×2×4

HAKKO FR-410 station

HAKKO FR-4103 handpiece

(with N61-05 (ø1.0 mm [0.04 in] type S) nozzle)

Power cord

HAKKO FH-410 iron holder

(with cleaning sponge)

Tool box

Instruction Manual

2. SPECIFICATIONS

● HAKKO FR-410

Power consumption

Temperature range

Temperature stability

190 W

330 - 450℃(620 - 850℉)

±5℃(±9℉) at idle temperature

● Station

Output

Vacuum generator

Vacuum pressure (max.)

Suction flow

Dimensions

Weight

AC 24 V

Vacuum pump, double cylinder type

80 kPa (600 mmHg)

15 L/min.

165 (W) × 137 (H) × 244 (D) mm

(6.5 × 5.4 × 9.6 in.)

4.8 kg (10.6 lb.)

●Handpiece (HAKKO FR-4103)

Part name

Power consumption

Nozzle to ground resistance

Nozzle to ground potential

Cord

Length (w/o cord)

Weight (w/o cord)

HAKKO FR-4103

140 W (24 V)

<2 Ω

<2 mV

1.2 m (4 ft.)

168 mm (6.6 in.) with N61-05 nozzle

190 g (0.42 lb.) with N61-05 nozzle

* The temperature was measured using the HAKKO FG-101

Soldering Tester.

* This product is protected against electrostatic discharge.

* Specifications and design are subject to change without notice.

1. PACKING LIST AND PART NAMES Please check to make sure that all items

listed below are included in the package.

Nozzle (N61 series)

Filter pipe

Trigger

HAKKO FR-4103

CAUTION

■ Electrostatic Protection

3. WARNINGS, CAUTIONS AND NOTES

WARNING

CAUTION

To prevent accidents or damage to the HAKKO FR-410, be sure to observe the following:

● Do not use the unit for applications other than desoldering.

● Do not strike the handpiece against hard objects to remove excess solder. This will

damage the handpiece.

● Do not modify the HAKKO FR-410.

● Use only genuine HAKKO replacement parts.

● Do not allow the HAKKO FR-410 to become wet, or use it when hands are wet.

●

Be sure to hold the plug when inserting or removing the handpiece and power cords.

● Be sure the work area is well ventilated. Desoldering produces smoke.

● While using the HAKKO FR-410, don't do anything which may cause bodily harm

or physical damage.

When power is ON, the nozzle will be hot. To avoid injury or damage to

personnel and items in the work area, observe the following:

● Donottouchthenozzleorthemetalpartsnearthenozzle.

●

Donotallowthenozzletocomecloseto,ortouch,ﬂammablematerials.

●

Informothersintheareathattheunitishotandshouldnotbetouched.

● Turnthepoweroﬀwhennotinuse,orleftunattended.

● TurnthepoweroﬀwhenchangingpartsorstoringtheHAKKO

FR-410.

● Thisunitisforcounterorworkbenchuseonly.

●

This appliance can be used by children aged from 8 years and above

and persons with reduced physical, sensory or mental capabilities or

lack of experience and knowledge if they have been given supervision

or instruction concerning use of the appliance in safe way and

understand the hazards involved.

● Children shall not play with the appliance.

●

Cleaning and user maintenance shall not be made by children

without supervision.

Warnings, cautions and notes are placed at critical points in this manual to direct the

operator’s attention to significant items. They are defined as follows:

W A R N I N G：FailuretocomplywithaWARNINGmayresultinseriousinjuryordeath.

CAUTION：FailuretocomplywithaCAUTIONmayresultininjurytotheoperator,

ordamagetotheitemsinvolved.



N O T E：ANOTEindicatesaprocedureorpointthatisimportanttotheprocess

beingdescribed.

CAUTION

Increasing the angle of the handpiece receptacle will cause

an increase in the handpiece temperature.

NOTE :

You can put nozzles that are not in use on the radial tray

of the cleaner base.

4. INITIAL SETUP

Loosen the adjusting screws to change the angle of the handpiece

receptacle as you like, then tighten the screws.

A. Iron holder

● Setup the iron holder

Following the instructions given in the illustration on the right,

assemble the iron holder.

Cleaner base

Radial tray

● How to use the cleaning sponge

The sponge is compressed. It will swell when moistened

with water. Before using the unit, dampen the sponge with

water and squeeze it to remove excess water.

CAUTION

Be sure the sponge is moistened with water before use to avoid damaging the nozzle.

1. Fit the small sponge pieces into the hollows in the

cleaner base.

2. Add an appropriate amount of water into the cleaner

base. The small sponge pieces will absorb water

and help keep the larger sponge damp at all times.

3. Dampen the large sponge, squeeze it to remove excess

water and put it on the cleaner base.

Cleaning

sponge

(Large)

(Small)

Turn the power

switch ON.

Connect the hose.

3. Set the HAKKO FR-4103 in the iron holder.

CAUTION

Be sure to hold the plug when inserting or removing the handpiece cord.

B. Station

● Connection

1. Connect the power cord to the receptacle on the

rear of the station.

2. Connect the plug from the HAKKO FR-4103

to the receptacle on the HAKKO FR-410.

CAUTION

Connect the plug to the receptacle, aligning the tab

on the plug with the opening on the receptacle.

Insert the plug into

the receptacle until

it seats.

To disconnect, pull the plug

from the receptacle while

pressing down the tab on

the plug.

Receptacle

4. Connect the hose from the HAKKO FR-4103

to the vacuum outlet cap on the HAKKO

FR-410 station.

5. Plug the power cord into a grounded power outlet.

Ensure that the power switch is OFF before

plugging in the power cord.

CAUTION

Be sure to ground this product as it is ESD

safe by design.

6. Turn the power switch ON.

5. OPERATION

PART NAMES

Control

Buttons

Receptacle Power Switch

- Moving the cursor UP. Increases the value.

- Moving the cursor DOWN.

Decreases the value.

- End of sequence (terminates a phase

of a data entry mode).

DOWN

ENTER

The HAKKO FR-410 has three controls

Vacuum

outlet cap

Normal display screen

CAUTION

When not in use, place the handpiece in

the iron holder.

CAUTION

Increasing the angle of the handpiece receptacle will cause

an increase in the handpiece temperature.

NOTE :

You can put nozzles that are not in use on the radial tray

of the cleaner base.

4. INITIAL SETUP

Loosen the adjusting screws to change the angle of the handpiece

receptacle as you like, then tighten the screws.

A. Iron holder

● Setup the iron holder

Following the instructions given in the illustration on the right,

assemble the iron holder.

Cleaner base

Radial tray

● How to use the cleaning sponge

The sponge is compressed. It will swell when moistened

with water. Before using the unit, dampen the sponge with

water and squeeze it to remove excess water.

CAUTION

Be sure the sponge is moistened with water before use to avoid damaging the nozzle.

1. Fit the small sponge pieces into the hollows in the

cleaner base.

2. Add an appropriate amount of water into the cleaner

base. The small sponge pieces will absorb water

and help keep the larger sponge damp at all times.

3. Dampen the large sponge, squeeze it to remove excess

water and put it on the cleaner base.

Cleaning

sponge

(Large)

(Small)

Turn the power

switch ON.

Connect the hose.

3. Set the HAKKO FR-4103 in the iron holder.

CAUTION

Be sure to hold the plug when inserting or removing the handpiece cord.

B. Station

● Connection

1. Connect the power cord to the receptacle on the

rear of the station.

2. Connect the plug from the HAKKO FR-4103

to the receptacle on the HAKKO FR-410.

CAUTION

Connect the plug to the receptacle, aligning the tab

on the plug with the opening on the receptacle.

Insert the plug into

the receptacle until

it seats.

To disconnect, pull the plug

from the receptacle while

pressing down the tab on

the plug.

Receptacle

4. Connect the hose from the HAKKO FR-4103

to the vacuum outlet cap on the HAKKO

FR-410 station.

5. Plug the power cord into a grounded power outlet.

Ensure that the power switch is OFF before

plugging in the power cord.

CAUTION

Be sure to ground this product as it is ESD

safe by design.

6. Turn the power switch ON.

5. OPERATION

PART NAMES

Control

Buttons

Receptacle Power Switch

- Moving the cursor UP. Increases the value.

- Moving the cursor DOWN.

Decreases the value.

- End of sequence (terminates a phase

of a data entry mode).

DOWN

ENTER

The HAKKO FR-410 has three controls

Vacuum

outlet cap

Normal display screen

CAUTION

When not in use, place the handpiece in

the iron holder.

●

When triggering before the heater reaches set temperature

HEAT I NG...

PLEASE

A I T

When triggering before the heater reaches set

temperature, the display screen shows “HEATING

...

PLEASE WAIT” and the vacuum does not work.

Please wait for the heater to reach the set temperature.

Nozzle

Board

Solder

Lead

1. Place the nozzle over the lead wire of the part to be

desoldered and begin heating.

Be careful to heat the lead wire and the solder, not the land.

Placing the nozzle directly in contact with the land may

cause the land to peel off. You may apply a small amount of

solder to form a heat bridge to help the heating process.

2. Check to make sure all of the solder on the joint has melted.

With the nozzle still in place over the lead wire, slowly move

the lead wire, being careful not to apply too much force. If

the lead wire moves easily, all of the solder has melted.

3. Pull the trigger to remove the melted solder.

4. If the solder was not removed, re-solder the part using new

solder and then repeat the desoldering process.

A. Desoldering

If the pump does not operate, immediately clean

the nozzle & heating element and replace the filter

if necessary.

CAUTION

Make sure that a filter has been inserted in the

desoldering tool. Desoldering without a filter may

damage the pump.

CAUTION

B.Making Changes to Settings

●

Selecting the preset number

When changing the temperature, there is a preset function

to manually set the temperature.

1. Press any of the

three control buttons.

<↑> <↓> <ENT>

PRESET1

PRESET2

PRESET3

660℉

750℉

840℉

2. The preset selection screen

appears.

5. OPERATION (continued)

● Changing various settings

(other than preset selections)

2. The setting selection screen

appears.

Press and hold any one

of the three control buttons

for at least 2 seconds.

The following settings

can be changed from

this screen:

4. Press the <ENT> button to

finalize your selection.

If you wish to exit the PRESET SELECTION screen...

Scroll the cursor to the bottom, select <EXIT>, and press the <ENT> button. You will

return to the normal display without making any changes.

Or if the device is left alone without making any operation for 10 seconds, you will

return to the normal display.

When changing the current set temperature or the preset temperature, follow the

operation of “

●

Changing various setting (other than preset selections)”.

<↓> <ENT>

4. Press the <ENT> button to

finalize your selection.

<↑>

3. Move the cursor UP or DOWN

by pressing the corresponding

buttons.

3. Move the cursor UP or DOWN

by pressing the corresponding

buttons.

<↓> <ENT>

660℉

750℉

840℉

<↑>

PRESET1

PRESET2

PRESET3

660℉

750℉

840℉

PRESET1

PRESET2

PRESET3

• Set Temp (Nozzle

temperature setting)

• Offset Temp

(Nozzle temperature

offset setting)

• Vacuum Check

(Check of nozzle clogging

and suction force)

• Preset Temp

(Setting of each

preset temperature)

• Preset ID (Setting

of each preset name)

• LCD Contrast

(Contrast adjustment

of display screen)

<EXIT>(Return to

the normal display)

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

●

When triggering before the heater reaches set temperature

HEAT I NG...

PLEASE

A I T

When triggering before the heater reaches set

temperature, the display screen shows “HEATING

...

PLEASE WAIT” and the vacuum does not work.

Please wait for the heater to reach the set temperature.

Nozzle

Board

Solder

Lead

1. Place the nozzle over the lead wire of the part to be

desoldered and begin heating.

Be careful to heat the lead wire and the solder, not the land.

Placing the nozzle directly in contact with the land may

cause the land to peel off. You may apply a small amount of

solder to form a heat bridge to help the heating process.

2. Check to make sure all of the solder on the joint has melted.

With the nozzle still in place over the lead wire, slowly move

the lead wire, being careful not to apply too much force. If

the lead wire moves easily, all of the solder has melted.

3. Pull the trigger to remove the melted solder.

4. If the solder was not removed, re-solder the part using new

solder and then repeat the desoldering process.

A. Desoldering

If the pump does not operate, immediately clean

the nozzle & heating element and replace the filter

if necessary.

CAUTION

Make sure that a filter has been inserted in the

desoldering tool. Desoldering without a filter may

damage the pump.

CAUTION

B.Making Changes to Settings

●

Selecting the preset number

When changing the temperature, there is a preset function

to manually set the temperature.

1. Press any of the

three control buttons.

<↑> <↓> <ENT>

PRESET1

PRESET2

PRESET3

660℉

750℉

840℉

2. The preset selection screen

appears.

5. OPERATION (continued)

● Changing various settings

(other than preset selections)

2. The setting selection screen

appears.

Press and hold any one

of the three control buttons

for at least 2 seconds.

The following settings

can be changed from

this screen:

4. Press the <ENT> button to

finalize your selection.

If you wish to exit the PRESET SELECTION screen...

Scroll the cursor to the bottom, select <EXIT>, and press the <ENT> button. You will

return to the normal display without making any changes.

Or if the device is left alone without making any operation for 10 seconds, you will

return to the normal display.

When changing the current set temperature or the preset temperature, follow the

operation of “

●

Changing various setting (other than preset selections)”.

<↓> <ENT>

4. Press the <ENT> button to

finalize your selection.

<↑>

3. Move the cursor UP or DOWN

by pressing the corresponding

buttons.

3. Move the cursor UP or DOWN

by pressing the corresponding

buttons.

<↓> <ENT>

660℉

750℉

840℉

<↑>

PRESET1

PRESET2

PRESET3

660℉

750℉

840℉

PRESET1

PRESET2

PRESET3

• Set Temp (Nozzle

temperature setting)

• Offset Temp

(Nozzle temperature

offset setting)

• Vacuum Check

(Check of nozzle clogging

and suction force)

• Preset Temp

(Setting of each

preset temperature)

• Preset ID (Setting

of each preset name)

• LCD Contrast

(Contrast adjustment

of display screen)

<EXIT>(Return to

the normal display)

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

●

Set Temp (Nozzle temperature setting)

1. Move the cursor to select “Set Temp”. After selecting, press <ENT>.

Entering from hundreds to units digit

Press the <↑> or <↓> to set the desired figure.

Press the <ENT> button to advance to the next digit.

Only values from 6 to 8 can be selected when entering the hundreds digit.

(In ℃mode, values from 3 to 4 can be selected.)

Values from 0 to 9 can be selected when entering the tens or units digits.

(The same values can be selected in ℃mode.)

3. When desired figure is displayed, press the button to enter.

The next digit will begin to flash. After entering the units digit, press the button to

save the figure to the system memory and begin heater control with new setting

temperature.

CAUTION

The temperature range is from 620 to 850℉. (330 to 450℃)

If you enter a value outside the temperature setting range, the display returns to

the hundreds digit, and you have to enter a correct value.

CAUTION

If power is switched off or lost during the execution of this procedure, no data

will be entered. The entire procedure must be repeated from step 1.

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

5. OPERATION (continued)

●

Offset Temp (Nozzle temperature offset setting)

Move the cursor to select “OffsetTemp”. After selecting, press <ENT>.

2. Enter the offset value (-05) which is the difference between tip temperature and set

temperature.

Press the <↑> or <↓> to set the desired figure.

Press the <ENT> button to advance to the next digit.

The hundreds digit can display 0 (for positive value) or minus sign. (for negative value)

(Same values can be selected in

℃

mode.)

Values from 0 to 9 can be selected when entering the ten digit.

(In ℃mode, values from 0 to 5 can be selected.)

Values from 0 to 9 can be selected when entering the units digit.

(Same values can be selected in ℃mode.)

3. After entering the units digit, press the button to save the figure to the system

memory and begin heater control with the new offset value.

CAUTION

During the offset setting, please be careful tip temperature does not exceed 850℉.

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

Example：If the measured temperature is 705℉and set temperature is 700℉, the

difference is -5℉. (need to decrease by 5℉) So, enter the figure which 5

is deducted from present offset value.

CAUTION

The allowable ranges for offset values are from -90 to +90℉. (In℃mode, from -50

to +50℃) If you enter a value outside the offset value range, the display returns to

the hundreds digit, and you have to enter a correct value.

●

Set Temp (Nozzle temperature setting)

1. Move the cursor to select “Set Temp”. After selecting, press <ENT>.

Entering from hundreds to units digit

Press the <↑> or <↓> to set the desired figure.

Press the <ENT> button to advance to the next digit.

Only values from 6 to 8 can be selected when entering the hundreds digit.

(In ℃mode, values from 3 to 4 can be selected.)

Values from 0 to 9 can be selected when entering the tens or units digits.

(The same values can be selected in ℃mode.)

3. When desired figure is displayed, press the button to enter.

The next digit will begin to flash. After entering the units digit, press the button to

save the figure to the system memory and begin heater control with new setting

temperature.

CAUTION

The temperature range is from 620 to 850℉. (330 to 450℃)

If you enter a value outside the temperature setting range, the display returns to

the hundreds digit, and you have to enter a correct value.

CAUTION

If power is switched off or lost during the execution of this procedure, no data

will be entered. The entire procedure must be repeated from step 1.

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

5. OPERATION (continued)

●

Offset Temp (Nozzle temperature offset setting)

Move the cursor to select “OffsetTemp”. After selecting, press <ENT>.

2. Enter the offset value (-05) which is the difference between tip temperature and set

temperature.

Press the <↑> or <↓> to set the desired figure.

Press the <ENT> button to advance to the next digit.

The hundreds digit can display 0 (for positive value) or minus sign. (for negative value)

(Same values can be selected in

℃

mode.)

Values from 0 to 9 can be selected when entering the ten digit.

(In ℃mode, values from 0 to 5 can be selected.)

Values from 0 to 9 can be selected when entering the units digit.

(Same values can be selected in ℃mode.)

3. After entering the units digit, press the button to save the figure to the system

memory and begin heater control with the new offset value.

CAUTION

During the offset setting, please be careful tip temperature does not exceed 850℉.

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<↑> <↓> <ENT>

Example：If the measured temperature is 705℉and set temperature is 700℉, the

difference is -5℉. (need to decrease by 5℉) So, enter the figure which 5

is deducted from present offset value.

CAUTION

The allowable ranges for offset values are from -90 to +90℉. (In℃mode, from -50

to +50℃) If you enter a value outside the offset value range, the display returns to

the hundreds digit, and you have to enter a correct value.

●

Vacuum Check (Check of nozzle clogging and suction force)

During suction, the gauge indicating sucking status is shown at the lower side

of the screen.

When “CHK” appears and you notice that the sucking force is weakening,

perform “Vacuum Check”.

Move the cursor to select “Vacuum Check”. After selecting, press <ENT>.

Pull the trigger.

3. When “Clogging” appears, perform cleaning and replace filters.

Suction gauge Sign of clogging

CHK

<↑> <↓> <ENT>

S e t T emp

O f f s e t T emp

Vacuum Check

680ﾟ F

00ﾟ F

<EXIT>

Vacuum Check

P u ll T r i gge r

<EXIT>

Vacuum Check

P u ll T r i gge r

O K

<EXIT>

Vacuum Check

P u ll T r i gge r

Clo g ging

No degradation in sucking force Degradation in sucking force

4. Select <EXIT>, and press the <ENT> button to return to the selection screen.

5. OPERATION (continued)

●

Preset Temp (Setting of each preset temperature)

1. Move the cursor to select “Preset Temp”. After selecting, press <ENT>.

Select the preset No. whose temperature setting you wish to change.

Entering from hundreds to units digit

Press the <↑> or <↓> to set the desired figure.

Press the <ENT> button to advance to the next digit.

Only values from 6 to 8 can be selected when entering the hundreds digit.

(In ℃mode, values from 3 to 4 can be selected.)

Values from 0 to 9 can be selected when entering the tens or units digits.

(The same values can be selected in ℃mode.)

3. After entering the units digit, press the button to save the figure to the system

memory and begin heater control with new setting temperature.

4. To exit from each setting screen, scroll the screen, select <EXIT>, and press the

<ENT> button.

CAUTION

If power is switched off or lost during the execution of this procedure, no data

will be entered. The entire procedure must be repeated from step 1.

<↑> <↓> <ENT>

O f f s e t T emp

Vacuum Check

P r ese t T emp

00ﾟ F

<↑> <↓> <ENT>

P1 T emp

P2 T emp

P3 T emp

660ﾟ F

750ﾟ F

840ﾟ F

<↑> <↓> <ENT>

PRESET1 TempS e t

60ﾟ F

<↑> <↓> <ENT>

PRESET1 TempS e t

6 0ﾟ F

<↑> <↓> <ENT>

PRESET1 TempS e t

66 ﾟ F

<↑> <↓> <ENT>

P2 T emp

P3 T emp

<EXIT>

750ﾟ F

840ﾟ F

CAUTION

The temperature range is from 620 to 850℉. (330 to 450℃)

If you enter a value outside the temperature setting range, the display returns to

the hundreds digit, and you have to enter a correct value.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hakko Electronics Elektrowerkzeuge Handbücher

Hakko Electronics

Hakko Electronics FR-410 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-9703 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2023 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-9707 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2023 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-8003 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM2022-05 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 470B Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2030 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 933 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-410 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-204 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FU-600 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FU-601 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2031 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2022 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-601 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-950 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 807 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-4104 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR410-52 Bedienungsanleitung

Hakko Electronics

Hakko Electronics B5166 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR400-53 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FT-8004 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch

Silca

Silca MARKER 2000 Bedienungsanleitung