Hakko Electronics 933 Bedienungsanleitung

ヒーター交換取扱説明書

No.

A1232(933/934 用 )

危険







     



  

    

       







● 



●     



● 



      







    

 

 







 

 









        

 











  





● 





 

















曲げる

2020.3

MA00225XZ200330

WARNING

Grounding wire

connected to back.

Heater Tube

64mm

Model

933/934

Specification

100, 110V

220~240V

Number

052

140

Bend

CAUTION

Solder the wires so that the solder in the lead hole

can be seen from both sides of the board. Insert the

heater lead (RED) from the opposite of IC.

F. Cut away the unneeded portion of the lead

wires and then cover the heater terminal with

the heater tube.

G. Securely insert the grounding spring into the

round sleeve on the opposite side from the lead

wire.

H. Replace the board along the groove on the grip,

making sure that the temperature button socket

is facing the right direction.

I. Reassemble by following the disassembly

procedure in reverse, and adjust the CAL to

calibrate the unit.

-When calibrating the soldering iron,use a new tip

as the temperature of a used tip may be lower

than normal due to deterioration.

-Do not set the temperature above 480℃ during

the CAL adjustment, as this may damage the unit.

1. After confirming that the power is off, pull out

the currently inserted button and insert the

desired one.

2. Pull back the handle cover to expose the CAL

adjustment hole.

3. Insert the plug of the power cord into the outlet.

The heater power lamp will begin blinking when

the soldering iton has reached the set temper-

ature.

4. While measuring the tip temperature; with a tip

thermometer, adjust the CAL using straight-

edge(-)screw driver. Turning the CAL clockwise

increase the temperature; turning it counter-

clockwise decrease the temperature.

If you have the P.W.B. with the hole for sensor

lead (blue) is located 2mm away from the edge,

please bend the sensor lead as shown in the figure

below. Then cover the heater tube.

Temp. Calibration

Sensor(Blue)

Heater(Red)

Number (052 or 140)

CAUTION

INSTRUCTIONMANUAL

FORREPLACING

THEHEATINGELEMENT

No.A1232(100V), No.A1272(110V),

No.A1273(220V), No.A1274(230V),

No.A1275(240V)

Always remove the power plug from the

outlet and wait for the soldering iron to

cool completely before replacing parts

or performing maintenance. Leaving the

unit plugged in during these operations

is dangerous and may result in electric

shock, failure, or reduced performance.

Replacing the Heating

Element

A. Remove the temp. button.

B. Remove the nut and disassemble the tip section.

C. Remove the screws and then remove the nipple.

D. Carefully pull out the heating element and

P.W.B., then remove the grounding spring.

E. Place a new heating element on the board as

shown in the figure below and solder it into

place. Check the number printed on the new

heating element. Errors in replacement may

result in failure or accident.

Dieses Handbuch passt für folgende Modelle

Andere Hakko Electronics Elektrowerkzeuge Handbücher

Hakko Electronics

Hakko Electronics FR-4104 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-410 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-9707 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2030 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-410 Bedienungsanleitung

Hakko Electronics

Hakko Electronics B5166 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FT-8004 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR-4103 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-601 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-9703 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2022 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 807 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-204 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FU-601 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2030 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-888D Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM-2023 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FU-600 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-600 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FX-8003 Bedienungsanleitung

Hakko Electronics

Hakko Electronics FM2022-05 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 474 Bedienungsanleitung

Hakko Electronics

Hakko Electronics 470B Bedienungsanleitung

Hakko Electronics

Hakko Electronics FR410-52 Bedienungsanleitung

Beliebte Elektrowerkzeuge Handbücher anderer Marken

AEG

AEG OMNI-JS Bedienungsanleitung

SIP

SIP 01533 Bedienungsanleitung

Ribimex

Ribimex PRS499 Bedienungsanleitung

3M Fiber Optic Connector Crimp Tool Bedienungsanleitung

Ryobi

Ryobi P524 Bedienungsanleitung

ROJEK

ROJEK FSN 300A Bedienungsanleitung

Kemper

Kemper 1740PRO Bedienungsanleitung

WABCO

WABCO OptiTire Bedienungsanleitung

EINHELL

EINHELL TE-MS 18/210 Li Bedienungsanleitung

Orgapack

Orgapack OR-T 85 Kurzanleitung

TOUGHCUT

TOUGHCUT Diamond 400 Bedienungsanleitung

Yaros

Yaros PB-3603 Bedienungsanleitung

Fein

Fein BSS 2.0 E Einrichtungshandbuch

Baileigh Industrial

Baileigh Industrial SS-2725 Bedienungsanleitung

Milwaukee

Milwaukee 2674-20 Bedienungsanleitung

Fein

Fein BLs 1.6 Bedienungsanleitung

Princess

Princess Electric Multi Sharpener Bedienungsanleitung

FOREDOM

FOREDOM K.1050 Handbuch