HAMPTON BAY FZ-12A Bedienungsanleitung

Dieses Handbuch passt für folgende Modelle

1

Andere HAMPTON BAY Lüfter Handbücher

HAMPTON BAY

HAMPTON BAY LDS-BF2002 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY 132 cm Fan Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY SEAPORT AL634-WH Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY HOLLIS 52196 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY MENA 92404 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY BPT18-34A-5 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Lonestar 52 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY 266-848 Installationsanleitung

HAMPTON BAY

HAMPTON BAY Andross Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY 91171 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Mena Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY 409-952 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY CEVA Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Renwick Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Copperhead Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY LK-GZL Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY PALM BEACH II 59299 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY SINCLAIR 798-072 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY AG524I-ORB Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY BPT13-13D-1 Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY SW18030 WH Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Hawthorne II Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Spoleto II Spoleto II Bedienungsanleitung

HAMPTON BAY

HAMPTON BAY Eastridge 640-659 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

1

FZ-12A

1000 026 990

Hand Screw

F

E

D

A B

C

G

1. Removing the Hand Screw

Carefully turn the fan on its side and

place on a table. Ensure the back of

the fan body faces upward. Loosen and

remove the hand screw (A) from the

front base (B) by turning

counterclockwise.

2. Base Assembly

Align the two portions of the circular

base and snap together by gently

pushing the two pillars at the bottom of

the rear base (C) into the two adjacent

sockets of the front base (B). Ensure

the connections are tight and secure.

ASSEMBLY INSTRUCTIONS

center of the base assembly.

Place the power cord (D) through the

Carefully remove all contents from the plastic bag and gift box.

CAUTION : THIS FAN MUST OPERATE STANDING UPRIGHT.

DO NOT USE WITHOUT BASE.

3. Securing the Tower Fan to the

Base Assembly

3

D

ASSEMBLY INSTRUCTIONS

6

5

A

4

4. Securing the Power Cord to the

Base Assembly

With the fan still on its side, locate the

power cord holding bracket at the

bottom of the base assembly. Gently

pull any slack out of the power cord,

place the power cord securely in the

holding bracket and secure the power

cord bracket over the power cord. Then

thread the power cord through the “U”

locating notch on the edge of the base

assembly. ( Fig. 6 )

Insert and tighten the hand screw (A)

into the hexagonal screw hole to

secure the base assembly to the tower

fan unit. ( Fig. 5 )

Return the tower fan to its upright

position.

Note: Do not operate the tower fan unless it is

in its proper, upright position.

Align the arrow on the base assembly

(which is near the central hole of the

base assembly ) with the arrow on the

rear of the tower fan unit and push the

base assembly close to the tower fan

unit tightly.Firmly hold the fan body

steady and rotate the base assembly

clockwise until three plastic hooks on

the tower fan bottom lock unto the three

open slots of the base assembly tightly.

You should now notice that the

hexagonal screw hole on the base

assembly is aligned with the screw hole

on the bottom of the tower fan unit.

( Fig. 4 )

9

VENTILADOR DE TORRE

GIRATORIO DE 71,1CM

FZ-12A

F

E

D

A B

C

G

DESCRIPCIÓN CANTIDAD

Tornillo

1

Base frontal 1

Base posterior 1

1

1

1

Botón de oscilación 1

PIEZA

A

B

C

D

E

F

G

Interruptor de perilla giratorio

Cable de alimentación

Tuerca de montaje de la

rejilla posterior

10