Harbor Breeze GAT24MBK6LOD Bedienungsanleitung

GASKIN CEILING FAN

ITEM #2889555

MODEL #GAT24MBK6LOD

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-888-251-1003, 8 a.m. - 8 p.m., EST, Monday - Sunday. You could

also contact us at [email protected] or visit www.lowespartsplus.com

Purchase Date

Español p. 16

ATTACH YOUR RECEIPT HERE

ADJUNTE SU RECIBO AQUÍ

Harbor Breeze® and logo design are

trademarks or registered trademarks

JS20025

4007498

APPROVED FOR USE IN

WET LOCATIONS

TABLE OF CONTENTS

Modifications not approved by the party responsible for compliance could void the user's authority to

operate the equipment.

*NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates,

uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

* Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Distributed by: Litex Industries Inc., P.O. Box 535639, Grand Prairie, TX, 75053

The device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, (2) this device must accept any

interference received, including interference that may cause undesired operation.

SAFETY INFORMATION

Safety Information ........................................................................................................................ 2

Package Contents ........................................................................................................................ 5

Hardware Contents ...................................................................................................................... 6

Preparation .................................................................................................................................

Initial Installation ........................................................................................................................... 7

Final Installation ............................................................................................................................ 9

Operating Instructions .............................................................................................................. 12

Troubleshooting.........................................................................................................................

Care and Maintenance ............................................................................................................... 15

Limited Lifetime Warranty ..........................................................................................................

Replacement Parts List .............................................................................................................. 15

READ AND SAVE THESE INSTRUCTIONS

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring

handbook if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 ft. from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 13 lbs.

SAFETY INFORMATION

DO NOT suspend any fixture by the house wires. Fan must always be mounted

directly to an eye bolt which is first attached to the building structure. The power cord

alone will not support the weight of the fan. Suspending a fan by the plug will result in

the fan falling, with the possibility of personal injury and the danger of electrical shock or fire.

Secure the eye bolt directly to the building structure. The eye bolt and its support must be able to

support the moving weight of the fan (at least 35 lbs.).

To avoid personal injury, the use of gloves may be necessary while handling fan parts with sharp

edges.

To reduce the risk of fire or electrical shock, do not use the fan with any solid-state speed control

device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock or personal injury, do not bend the blades when

installing or balancing them or cleaning the fan. Do not insert objects between the rotating fan

blades.

WARNING

DANGER

When using an eye bolt, make sure the eye bolt is securely attached to the building structure

and can support the full weight of the fan. Failure to do this can result in serious injury or death.

The stability of the eye bolt is essential in minimizing wobble and noise in the fan after installation

is complete.

To reduce the risk of serious bodily injury, DO NOT use power tools to assemble any part of the

fan, including the blades.

If using this fan in a WET location, connect this product to a Ground Fault Circuit Interrupting

(GFCI) outlet to reduce the risk of personal injury, electrical shock or death. If one is not provided,

contact a qualified electrician for proper installation.

SAFETY INFORMATION

CAUTION

Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

Once installation is complete, carefully check all screws, bolts and nuts on fan motor assembly to

ensure that they are secured.

Do NOT tamper with or attempt to repair LED component. The light source is designed for this

specific application and should not be serviced by untrained personnel. If any servicing is

required, call our customer service department.

This portable fan has a polarized plug (one blade is wider than the other) as a safety feature to

reduce the risk of electric shock. This plug will fit in a polarized outlet only one way. If it does not fit

fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. NEVER use

with an extension cord unless the plug can be fully inserted. DO NOT alter the plug.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

To reduce the risk of electric shock, DO NOT use the product if power cord is frayed or broken.

To reduce the risk of burns, fire, electric shock or injury to persons, unplug from outlet before

putting on or taking off parts.

As a safety precaution, unplug power supply cord when not in use.

DO NOT use staples or nails to secure wiring/power supply cord from light fixture.

DO NOT place wiring/power supply cord on sharp hooks or nails.

DO NOT hang ornaments or other objects from power supply cord, wire or lights.

DO NOT close doors and/or windows on the light fixture power supply cord as doing so may

damage the insulation wire(s).

WARNING

IMPORTANT REMINDER: You must use the

parts provided with this fan for proper installation

and safety.

A Downrod 1

B Motor Housing 1

C Yoke Cover 1

D LED Light Kit 1

E Blade 6

F Switch Housing 1

G Shade 1

HPin (preassembled) 1

DESCRIPTIONPART QUANTITY

PACKAGE CONTENTS

DESCRIPTIONPART QUANTITY

I Clip (preassembled) 1

J Blade Arm 6

K Switch Housing Screw 3

(preassembled)

L Motor Plate Screw 3

(preassembled)

M Motor Screw/Lock Washer 12

(preassembled) + 1 extra

PREPARATION

HARDWARE CONTENTS (shown actual size)

Before beginning assembly of product, make sure all parts are present. Place motor on carpet or on

foam to avoid damage to ﬁnish. Compare parts with package contents list and hardware contents list. If

any part is missing or damaged, do not attempt to install, operate or assemble the product.

Estimated Assembly Time: 60 minutes.

Tools Required for Assembly (not included): Phillips Screwdriver, Pliers, Safety Glasses, Stepladder.

Helpful Tools (not included): AC Tester Light, Tape Measure.

AA BB

Blade

Screw

Qty. 18

+ 1 extra

Rubber

Blade

Washer

Qty. 18

+ 1 extra

Zip Tie

Qty. 1

Clamp

Qty. 6

Pull Chain

Extension

Qty. 2

INITIAL INSTALLATION

1. Remove preassembled motor screws/lock washers

(M) from underside of motor housing (B). If there

are plastic motor blocks installed with the motor

screws/lock washers (M), discard the plastic motor

blocks.

Note: Make sure to keep loose hardware separate

to avoid confusion during installation.

Plastic

Motor

Block

Remove pin (H) and clip (I) from downrod (A).

Partially loosen preassembled set screws and nut

in motor housing yoke at top of motor housing (B).

2a. 2a

Set Screw

Sideview

Yoke

2b.

3. Insert downrod (A) through yoke cover (C). Slip

downrod (A) into motor housing yoke, align holes

and re-install pin (H) and clip (I). Tighten set

screws in motor housing yoke and then tighten

preassembled nut on one of the set screws. Then,

slide yoke cover (C) down until it rests on top of

motor housing (B).

Yoke

Set Screw

and Nut

Sideview

INITIAL INSTALLATION

6. Remove liner from back of clamp (DD). Place

clamps (DD) alongside the path of the power cord

and insert power cord into clamps (DD), making

sure the cord does not hang in the way of the fan.

Hardware Used

Clamp x 6

5. Clip downrod (A) to secured eye bolt. Check the

length of the power cord from the outlet to the fan

(do NOT plug in the fan). Using the zip tie (EE)

secure power cord slack to the side of the

downrod.

Hardware Used

Zip Tie x 1

4. 4

Secure an eye bolt (not included) to ceiling of

building structure.

*NOTE: It is very important you use the proper

hardware when installing the eye bolt as this will

support the fan.

FINAL INSTALLATION

DANGER: To reduce the risk of serious bodily

injury, DO NOT use power tools to assemble the

blades (E). If screws are overtightened, blades (E)

may crack and break.

Partially insert three blade screws (AA) along with

three rubber blade washers (BB) into holes in blade

(E) (labeled THIS SIDE UP) to attach blade arm (J) to

blade (E). Then, tighten each blade screw (AA)

starting with the one in the middle.

Repeat Step 2 for remaining blades (E) and blade

arms (J).

Rubber Blade Washer x 18

Hardware Used

AA Blade Screw x 18

Attach blade arms (J) to the bottom of motor housing

(B) with motor screws/lock washers (M) previously

removed (Step 1, page 6). Tighten motor screws/lock

washers (M) securely.

NOTE: Make sure to completely secure each blade

arm (J) before proceeding to the next.

3. Remove one motor plate screw (L) from motor

plate preassembled on the underside of the motor

housing (B) and partially loosen the other two

motor plate screws (L). Align slotted holes in

switch housing (F) with loosened motor plate

screws (L), allowing molex connections from

motor housing (B) to come through hole in switch

housing (F). Twist switch housing (F) to lock.

Re-insert the motor plate screw (L) that was

removed and securely tighten all three motor plate

screws (L).

Motor

Plate

FINAL INSTALLATION

4. Remove two switch housing screws (K) from

underside of switch housing (F) and partially

loosen the other switch housing screw (K).

molex

connections

Connect WHITE molex wire from LED light kit (D)

to WHITE molex wire from switch housing (F).

Connect BLUE molex wire from LED light kit (D) to

BLACK (or BLUE) molex wire from switch housing

(F). Make sure molex wire connections snap

together securely.

5. Connect male plug from motor housing (B) to female

plug from switch housing (F), matching up the colors

on the male plug with the colors on the female plug

for correct fit. Make sure plugs are connected

completely.

Male

Plug

Female

Plug

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Harbor Breeze Lüfter Handbücher

Harbor Breeze

Harbor Breeze PORTES LP8293LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze SOUTH RIVER C-ST52BNK5D1 Bedienungsanleitung

Harbor Breeze

Harbor Breeze KIAWAH Bedienungsanleitung

Harbor Breeze

Harbor Breeze LP8071LBN Bedienungsanleitung

Harbor Breeze

Harbor Breeze L0982 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BELLHAVEN II E-BLHII52VPW5C4S Bedienungsanleitung

Harbor Breeze

Harbor Breeze WCK52NWZ5D Bedienungsanleitung

Harbor Breeze

Harbor Breeze HTD20005 Bedienungsanleitung

Harbor Breeze

Harbor Breeze E-CAF56OSB5CRC Bedienungsanleitung

Harbor Breeze

Harbor Breeze Santa Ana LP8294LBN Bedienungsanleitung

Harbor Breeze

Harbor Breeze TIEMPO E-TM52BNK5CS Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40107 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40956 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 80209 Bedienungsanleitung

Harbor Breeze

Harbor Breeze AFTONSHIRE Bedienungsanleitung

Harbor Breeze

Harbor Breeze SOUTHLAKE LP8055LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze Teolo Bedienungsanleitung

Harbor Breeze

Harbor Breeze 0228113 Bedienungsanleitung

Harbor Breeze

Harbor Breeze ARMITAGE CC52WW5C1 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BELCARRA CE-JP13BNK6RC Bedienungsanleitung

Harbor Breeze

Harbor Breeze Calera Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40945 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 35061 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 42299 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung