Harbor Breeze BELLHAVEN II E-BLHII52VPW5C4S Bedienungsanleitung

Questions, problems, missing parts? Before returning to your retailer, call or contact our

customer service department at 1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

Harbor Breeze® is a registered trademark

ATTACH YOUR RECEIPT HERE

Serial Number Purchase Date

Federal regulations require ceiling fans with light kits manufactured or imported after

January 1, 2009, to limit total wattage consumed by the light kit to 190W. Therefore,

this fan is equipped with a wattage limiting device. If you lamp this fan's light kit with

bulbs totaling more than 190W, the wattage limiting device will reduce the watts

consumed to 190W.

ITEM #18039

MODEL #E-BLHII52VPW5C4S

BELLHAVEN II CEILING FAN

español p. 20

E192641

TABLE OF CONTENTS

Safety Information ………………………………………………………...……..…...............2 - 3

Package Contents ……………………………………………………..……..…..…..................4

Hardware Contents ..................

....

........................................................................................

.........

Preparation ....….…………………..……………………….…………….……………............5

Initial Installation .........……………………...………………………………………

….

......6 - 7

Fan Mounting ..........…………………………………………………...................................7 - 9

Wiring ...................…………………….............................................………

......

.............9 - 11

Final Installation …………….……………………….…………….……..............

.…..

..........11 - 14

Operation Instructions .......................…………………………....................................15 - 16

Care and Maintenance ……………………………………………………………..……………........16

Troubleshooting .....………...………………………….……………..………......................17 - 18

Warranty ……………………………….…………………………………………..…..................18

Replacement Parts List .......................................................................................................

....

READ AND SAVE THESE INSTRUCTIONS

Please read and understand this entire manual before attempting to assemble, install or operate the

product. If you have any questions regarding the product, please call customer service at

1-800-527-1292, 8:30 a.m. - 5:00 p.m., CST, Monday - Friday.

• Do not discard fan carton or foam inserts. Should this fan need to be returned to the factory for

repairs, it must be shipped in its original packaging to ensure proper protection against damage that

might exceed the initial cause for return.

• Make sure that all electrical connections comply with local codes, ordinances, the National Electrical

Code and ANSI/NFPA 70-1999. Hire a qualified electrician or consult a do-it-yourself wiring handbook,

available at Lowe's, if you are unfamiliar with installing electrical wiring.

• Make sure the installation site you choose allows a minimum clearance of 7 feet from the blades to

the floor and at least 30 in. from the end of the blades to any obstruction.

• After you install the fan, make sure that all connections are secure to prevent the fan from falling.

• The net weight of this fan including the light kit is: 25 lbs. (11.34 kg).

SAFETY INFORMATION

To reduce the risk of fire, electrical shock, or personal injury, mount fan to outlet box

marked "ACCEPTABLE FOR FAN SUPPORT OF 35 LBS (15.9 KG) OR LESS" and use

mounting screws provided with the outlet box. Most outlet boxes commonly used for the

support of lighting fixtures are not acceptable for fan support and may need to be replaced.

Consult a qualified electrician if in doubt.

When mounting fan to a ceiling outlet box, use a METAL octagonal outlet box. Secure the outlet

box directly to the building structure. The outlet box and its support must be able to support the

moving weight of the fan (at least 35 lbs.). Do NOT use a plastic outlet box.

To avoid personal injury, the use of gloves may be necessary while handling fan parts with

sharp edges.

To reduce the risk of fire, electrical shock, or personal injury, wire connectors provided with this

fan are designed to accept only one 12-gauge house wire and two lead wires from the fan. If your

house wire is larger than 12-gauge or there is more than one house wire to connect to the two fan

lead wires, consult an electrician for the proper size wire connectors to use.

To reduce the risk of fire or electrical shock, do not use the fan with any solid state speed

control device or control fan speed with a full range dimmer switch.

To reduce the risk of fire, electrical shock, or personal injury, do not bend the blade arms when

installing them, balancing the blades, or cleaning the fan. Do not insert objects between the

rotating fan blades.

To reduce the risk of personal injury, use only parts provided with this fan. The use of parts

OTHER than those provided with this fan will void the warranty.

WARNINGS

CAUTIONS

Before proceeding, be sure to shut off electricity at main switch or circuit breaker in order to avoid

electrical shock.

Read all instructions and safety information before installing your new fan. Review the

accompanying assembly diagrams.

IMPORTANT REMINDER: You must

use the parts provided with this fan for

proper installation and safety.

PACKAGE CONTENTS

PART DESCRIPTION QUANTITY

A Downrod 1

B Canopy 1

C Mounting Bracket 1

D Motor Housing 1

E Fitter Plate 1

F Yoke Cover 1

G Light Kit Fitter 1

H Blade Arm 5

I Blade 5

J Glass Shade 4

K Motor Screw 10

(preassembled)

L Lock Washer 10

(preassembled)

PART DESCRIPTION QUANTITY

M Canopy Mounting Screw 2

(preassembled)

N Pin (preassembled) 1

O Clip (preassembled 1

P Pull Chain Extension 2

Q Socket Ring 4

(preassembled)

R Finial (preassembled) 1

S Candelabra Base Bulb 4

T Canopy Cover 1

U Motor Plate Screw 3

(preassembled)

HARDWARE CONTENTS (shown actual size)

Blade

Screw

Qty. 15

Before beginning assembly of product, make sure all parts are present. Compare parts with package

contents list and hardware contents above. If any part is missing or damaged, do not attempt to

assemble the product. Contact customer service for replacement parts.

Estimated Assembly Time: 120 minutes

Tools Required for Assembly (not included): Electrical Tape, Phillips Screwdriver, Pliers, Safety

Glasses, Stepladder and Wire Strippers

Helpful Tools (not included): AC Tester Light, Tape Measure, Do-It-Yourself Wiring Handbook

(available at Lowe’s) and Wire Cutters

Bulbs Required (included): 4 candelabra base 40-watt max. bulbs

DANGER: When using an existing outlet box, make sure the outlet box is securely attached to

the building structure and can support the full weight of the fan. Failure to do this can result in serious

injury or death. The stability of the outlet box is essential in minimizing wobble and noise in the fan

after installation is complete.

CAUTION: Be sure outlet box is properly grounded and that a ground wire (green or bare) is

present.

After opening top of carton, remove mounting hardware package from foam inserts. Remove motor

from packing and place on carpet or on foam to avoid damage to ﬁnish.

CAUTION: Carefully check all screws, bolts and nuts on fan motor assembly to ensure that they

are secured.

PREPARATION

E3 Wire

Connector

Qty. 4

Fiber

Blade

Washer

Qty. 15

INITIAL INSTALLATION

Turn off circuit breakers and wall switch to the fan

supply line leads. (Fig. 1)

DANGER: Failure to disconnect power supply

prior to installation may result in serious injury or

death.

Check to make sure blades (I) are at least 30 in.

from any obstruction. Check downrod (A) length to

ensure blades (I) are at least 7 ft. above the floor.

(Fig. 3)

OFF

7 ft.

min.

30 in.

min.

Determine mounting method to use. (Fig. 2)

A. Normal mount

B. Angle mount

Important: If using the angle mount, check to

make sure the ceiling angle is not steeper than 19°.

INITIAL INSTALLATION

5. Remove motor screws (K) and lock washers (L)

from underside of motor and save for blade arm

(H) attachment later on. [If there are plastic motor

blocks installed with the motor screws (K) and

lock washers (L), discard the plastic motor

blocks.] (Fig. 5)

FAN MOUNTING

Set

Screw

Remove pin (N) and clip (O) from motor housing

yoke at top of motor housing (D) and partially

loosen set screws. (Fig. 1)

*Helpful Hint: Downrod style mounting is best

suited for ceilings 8 ft. (2.44 m) high or higher.

For taller ceilings you may want to use a longer

downrod (not included) than the one provided.

Angle style mounting is best suited for angled or

vaulted ceilings. A longer downrod is sometimes

necessary to ensure proper blade clearance.

Secure mounting bracket (C) to outlet box using

screws, spring washers, and flat washers

provided with the outlet box. (Fig. 4)

*NOTE:It is very important that you use the

proper hardware when installing the mounting

bracket (C) as this will support the fan.

IMPORTANT: If using the angle mount, make

sure open end of mounting bracket (C) is installed

facing the higher point of the ceiling.

4. 4

Depending on the length of downrod (A) you

use, you may need to cut the lead wires back to

simplify the wiring. If you decide to cut back the

lead wires, it is suggested that you do so in the

following manner:

Take the lead wires and make sure that you

have pulled them all the way through the top of

the downrod (A). Start at the TOP of the ball on

the downrod (A) and measure 8 in. of lead wire,

and then cut the excess wire off with wire cutters

(not included). (Fig. 4)

Note: If you do not cut back the lead wires,

Steps 4 and 5 are not necessary and you may

proceed to Step 6 instead.

FAN MOUNTING

Insert downrod (A) through canopy (B), canopy

cover (T), and yoke cover (F). [Note: Canopy

cover (T) must be turned with the shiny side

toward the motor housing (D).] Thread wires

from motor housing (D) through downrod (A).

(Fig. 2)

Slip downrod (A) into motor housing yoke, align

holes and re-install pin (N) and clip (O).

Re-tighten set screws in motor housing yoke and

then tighten nuts. Slide yoke cover (F) down until

it rests on top of motor housing (D). (Fig. 3)

2. 2

Set Screw

Ball

WIRING

WARNING: To reduce the risk of fire,

electrical shock, or personal injury, wire

connectors provided with this fan are designed

to accept only one 12-gauge house wire and two

lead wires from the fan. If your house wire is

larger than 12-gauge or there is more than one

house wire to connect to the two fan lead wires,

consult an electrician for the proper size wire

connectors to use.

CAUTION: Be sure outlet box is properly

grounded and that a ground (green or bare) wire is

present.

WARNING: If house wires are different

colors than referred to in the following steps,

stop immediately. A professional electrician is

recommended to determine wiring.

If you decided to cut back the lead wires in Step 4,

strip 1/2 in. of insulation from end of white wire.

Twist stripped ends of each strand of wire within

the insulation with pliers (not included). (Fig. 5)

Repeat Step 5 for black, blue (if applicable) and

green wires.

Install ball end of downrod (A) into mounting

bracket (C) opening. Align slot in ball with tab in

mounting bracket (C). (Fig. 6)

DANGER: Failure to align slot in ball with tab

may result in serious injury or death.

6. 6

Slot

Tab

FAN MOUNTING

WIRING

FAN AND LIGHT CONTROLLED BY PULL CHAINS

BLACK

WHITE

GROUND/GREEN (BARE)

WHITE

BLUE

WHITE

FROM FAN

120 V Power

FROM

CEILING

FAN

GREEN

BLACK

GREEN

Choose wiring diagram (Fig. 1A, Fig. 1B or Fig.

1C) that fits your situation and make appropriate

wiring connections as follows: [NOTE: For each

wire connection below, use one of the wire

connectors (CC) provided, making sure to screw

wire connector (CC) on in a clockwise direction.]

1A. FAN AND LIGHT CONTROLLED BY

PULL CHAINS: Connect BLACK and BLUE

wire from fan to BLACK wire from ceiling.

Connect WHITE wire from fan to WHITE wire

from ceiling. Connect all GROUND (GREEN)

wires together from fan (on downrod (A) and

mounting bracket (C)) to BARE/GREEN wire

from ceiling. (Fig. 1A)

WHITE

BLACK

BLACK (WALL SWITCH)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

GREEN

WHITE

GREEN

FAN CONTROLLED BY PULL CHAIN, LIGHT BY

WALL SWITCH

1B. FAN CONTROLLED BY PULL CHAIN,

LIGHT BY WALL SWITCH: If you intend to

control the fan light with a separate wall

switch, connect BLACK wire from fan to

BLACK wire from ceiling. Connect BLUE wire

from fan to the BLACK wire from the

independent wall switch for the light. Connect

WHITE wire from fan to WHITE wire from

ceiling. Connect all GROUND (GREEN) wires

together from fan (on downrod (A) and

mounting bracket (C)) to BARE/GREEN wire

from ceiling. (Fig. 1B)

NOTE: Black wire is hot power for fan. Blue wire

is hot power for light kit. White wire is common

for fan and light kit. Green or bare wire is ground.

FAN AND LIGHT CONTROLLED BY TWO WALL

SWITCHES

WHITE

BLACK (WALL SWITCH)

BLACK (WALL SWITCH FOR LIGHT)

GROUND/GREEN (BARE)

BLACK

BLUE

WHITE

FROM FAN

FAN

120 V Power

FROM

CEILING

GREEN

WHITE

GREEN

1C. FAN AND LIGHT CONTROLLED BY

TWO WALL SWITCHES: If you intend to

control the fan and light with separate wall

switches, connect BLACK wire from fan to

BLACK wire from the independent wall switch

for the fan. Connect BLUE wire from fan to the

BLACK wire from the other independent wall

switch for the light. Connect WHITE wire from

fan to WHITE wire from ceiling. Connect all

GROUND (GREEN) wires together from fan

(on downrod (A) and mounting bracket (C)) to

BARE/GREEN wire from ceiling. (Fig. 1C)

Inhaltsverzeichnis

Sprachen:

Andere Harbor Breeze Lüfter Handbücher

Harbor Breeze

Harbor Breeze C-TR56BNK3D1R Bedienungsanleitung

Harbor Breeze

Harbor Breeze 00881 Bedienungsanleitung

Harbor Breeze

Harbor Breeze E-ER56ORB3LKLR Bedienungsanleitung

Harbor Breeze

Harbor Breeze RC103L Bedienungsanleitung

Harbor Breeze

Harbor Breeze MARINA COVE II Bedienungsanleitung

Harbor Breeze

Harbor Breeze E-TM52BNK5LED Bedienungsanleitung

Harbor Breeze

Harbor Breeze MAZON MZ44MBK3LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze BUILDER'S SERIES 40698 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 52 IN CLASSIC STYLE 40081 Bedienungsanleitung

Harbor Breeze

Harbor Breeze STONECROFT 41946 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40410 Bedienungsanleitung

Harbor Breeze

Harbor Breeze CGR60WW3LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze TALAMORE TAL60MBK8LR Bedienungsanleitung

Harbor Breeze

Harbor Breeze ANNANDALE 42864 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BEACH CREEK TG44LW3D1RC Bedienungsanleitung

Harbor Breeze

Harbor Breeze 41161 Bedienungsanleitung

Harbor Breeze

Harbor Breeze LP8210LAZ Bedienungsanleitung

Harbor Breeze

Harbor Breeze ECHOLAKE 42080 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 42299 Bedienungsanleitung

Harbor Breeze

Harbor Breeze BRADBURY BRD48BNK6LRS Bedienungsanleitung

Harbor Breeze

Harbor Breeze LANSING 40198 Bedienungsanleitung

Harbor Breeze

Harbor Breeze WAVEPORT STYLE E-WK52NWZ5C1 Bedienungsanleitung

Harbor Breeze

Harbor Breeze 40360 Bedienungsanleitung

Harbor Breeze

Harbor Breeze KEYPORT HUGGER 40141 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung