Harbor Freight Tools 47980 Kurzanleitung

47980

ASSEMBLY & OPERATING INSTRUCTIONS

MECHANICS’

ROLLER SEAT

Brought to You By Augusta Flint

THANK YOU for choosing a HARBOR FREIGHT TOOLS product. For future reference, please complete the owner’s

record below:

Model___________ Serial No._____________ Purchase Date_____________

Save This Manual

You will need the manual for the safety warnings and precautions, assembly instructions, operating

and maintenance procedures, parts list and diagram. Keep your invoice with this manual. Write the

invoice number on the inside of the front cover. Keep the manual and invoice in a safe and dry

place for future reference.

Technical Specifications

Product Name: Mechanics’ Roller Seat

Product Number: 47980

Seat Dimension: 11" Deep x 17" Wide

Tool Tray Size: 17" Diameter x 7/8" Deep

Finish: Chromed Cylinder, chrome Casters, red Vinyl Seat Cover,

black Wheels, black painted metal

Dimensions: 28" high at back, 22" high at Seat

Fabrication: 1" Square Steel Tube, swivel casters, pressurized pneumatic

cylinder

Caster Support: Double ball bearing

Height Options: Adjusts from 17-1/2" to 22" high

Maximum Weight: 250 LBS.

Safety Warnings and Precautions

WARNING: When using product, basic safety precautions should always be followed to

reduce the risk of personal injury and damage to equipment.

Read all instructions before using this product!

1. Keep work area clean. Cluttered areas invite injuries.

2. Observe work area conditions. Do not use this product in damp or wet locations. Don’t

expose to rain. Keep work area well lighted.

3. Keep children away. Children must never be allowed in the work area. Do not let them

handle machines, tools, extension cords or this product. This product is not a toy.

4. Store idle equipment. When not in use, products must be stored in a dry location to inhibit

rust. Always lock up products and keep out of reach of children.

5. Use the right tool for the job. Do not attempt to force a small tool or attachment to do the

work of a larger industrial tool. There are certain applications for which this product was

designed. It will do the job better and more safely at the rate for which it was intended. Do not

modify this product and do not use this product for a purpose for which it was not intended.

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts.

Wear restrictive hair covering to contain long hair.

#47980 Page 2

Brought to You By Augusta Flint

7. Use eye and ear protection. Always wear ANSI approved impact safety goggles.

8. Check for damaged parts. Before using any product, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended function.

Check for alignment and binding of moving parts; any broken parts or mounting fixtures; and

any other condition that may affect proper operation. Any part that is damaged should be

properly repaired or replaced by a qualified technician.

9. Replacement parts and accessories. When servicing, use only identical replacement parts.

Use of any other parts will void the warranty. Only use accessories intended for use with this

product. Approved accessories are available from Harbor Freight Tools.

10. Do not operate product if under the influence of alcohol or drugs. Read warning labels on

prescriptions to determine if your judgment or reflexes are impaired while taking drugs. If there

is any doubt, do not operate the product.

11. Do not use the Mechanics’ Roller Seat as a scaffold, ladder, stool or any use not intended

for this product. This product is only meant to be used as a seat.

12. Make certain to use the Mechanics’ Roller Seat on a flat, level and even surface.

13. Gently sit on the Roller Seat. Falling into or sitting down hard on the seat could damage

the product.

Warning: The warnings, cautions, and instructions discussed in this instruction

manual cannot cover all possible conditions and situations that may

occur. It must be understood by the operator that common sense and

caution are factors which cannot be built into this product, but must be

supplied by the operator.

Assembly

Your Mechanics’ Roller Seat will require complete assembly prior to use. It is important that you

read the entire manual to become familiar with the unit BEFORE you use the Roller Seat. Before

assembling your Mechanics’ Roller Seat be sure that you have all parts described in the Parts List

located on the last pages of this manual.

Step 1) Attach the Up and Down Plate (#2) to the Seat (#1). Slide one Washer (#3) onto

each Hex Screw (#4). Insert one (1) Hex Screw (#4) with Washer (#3) up through

each corner of the Up and Down Plate (#2) and into the bottom of the Seat (#1).

Tighten all four (4) Hex Screws until Up and Down Plate (#2) is firm against

Seat (#1)-see Figure 1.

#47980 Page 3

Figure 1-Attaching Plate to Seat

Up and Down Plate (#2)

Hex Screw (#4) with Washer (#3)

Cotter Pin (#12)

Handle (#11)

Brought to You By Augusta Flint

Step 2) Place the small end of the Handle between the stays located on the Up and Down

Plate (#2). Secure in place by inserting Cotter Pin (#12) through the hole in the stay,

then through Handle (#11) and through second Stay. Place pin through Cotter

Pin (#12)-see Figure 1.

Step 3) Slide Seat (#1) with Up and Down Plate (#2) onto the end of the Pneumatic

Pump (#5).

Step 4) Slide Tool Tray (#8) over the bottom end of the Pneumatic Pump (#5) so that the

three (3) different Tray compartments face upward-see Assembly diagram.

Step 5) Slide the Base (#9) up onto the bottom of the Pneumatic Pump (#5) so that the holes

in the Tool Tray (#8) rest over the holes in each leg of the Base (#9).

Step 6) Slide the pin on the Rear Caster Wheel (#10) up through hole in the Base (#9) and

Tool Tray (#8). Slide on Washer (#6) and thread on Nut (#7). Repeat for the

remaining four (4) Rear Caster Wheels (#10)-see Figure 2.

Tool Tray (#8)-not shown

Rear Caster Wheel (#10)

Figure 2-Caster Wheel to Base

Base (#9)

Washer (#6) and Nut (#7)

Operation

To assist you with operation please refer to the Operational Figures as well as the Assembly

Diagram and Parts List located on the last pages of this manual. Note: Do not exceed the

maximum weight capacity of 250 Lbs.

Lowering the Seat

Step 1) While seated in the Roller Seat, press down on the Handle (#11). The Seat will lower

as you apply weight to the Seat. When the Roller Seat is at the desired height,

release the Handle (#11) and the Seat will be set in position.

Raising the Seat

Step 1) Press down on the Handle (#11) while the Seat is empty. The Seat will raise

upward to its’ maximum height.

#47980 Page 4

Brought to You By Augusta Flint

Unpacking

UNPACK AND CHECK CONTENTS

When unpacking your Mechanics’ Roller Seat, check to make sure the following parts are included.

If any parts are missing or broken, please call HARBOR FREIGHT TOOLS at 1-800-444-3353.

Parts List-Mechanics’ Roller Seat

Part # Description Quantity Part # Description Quantity

1Seat 1 7 Nut 5

2 Up and Down Plate 1 8 Tool Tray 1

3 Washer 4 9 Base 1

4 Hex Screw 4 10 Rear Caster Wheel-2-1/2" 5

5 Pneumatic Pump 1 11 Handle 1

6 Washer 10 12 Cotter Pin 1

Note: Some parts are listed and shown for illustration purposes only and are not

available individually as replacement parts.

Assembly Diagram

#47980 Page 5

Brought to You By Augusta Flint

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A

REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTA-

TION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS

TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT,

THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS RE-

PLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE

BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION

OF REPLACEMENT PARTS THERETO.

#47980 Page 6

Brought to You By Augusta Flint

Inhaltsverzeichnis

Andere Harbor Freight Tools Inneneinrichtung Handbücher

Harbor Freight Tools

Harbor Freight Tools PITTSBURGH AUTOMOTIVE 91200 Montageanleitung

Harbor Freight Tools

Harbor Freight Tools 40141 Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools 91615 Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools 91041 Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools 40089 Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools 66197 Installationshandbuch

Harbor Freight Tools

Harbor Freight Tools 92099 Wartungs- und Serviceanleitung

Harbor Freight Tools

Harbor Freight Tools 91460 Bedienungsanleitung

Harbor Freight Tools

Harbor Freight Tools 91735 Kurzanleitung

Harbor Freight Tools

Harbor Freight Tools 03491 Bedienungsanleitung

Beliebte Inneneinrichtung Handbücher anderer Marken

Homelegance

Homelegance California 1662PEK-1CK Bedienungsanleitung

Osmond Ergonomics

Osmond Ergonomics FLO Bedienungsanleitung

OVE

OVE ELOISE 42 Bedienungsanleitung

overstock

overstock MF286255 Bedienungsanleitung

Sonoma

Sonoma 160-801 Bedienungsanleitung

BOLERO

BOLERO Wicker Side Chair CF158 Installationsanleitung

Coaster

Coaster 4799N Bedienungsanleitung

Stor-It-All

Stor-It-All WS39MP Programmierhandbuch

Lexicon

Lexicon 194840161868 Bedienungsanleitung

Next AMELIA NEW 462947 Bedienungsanleitung

impekk

impekk Manual II Bedienungsanleitung

Elements

Elements Ember Nightstand CEB700NSE Bedienungsanleitung

JWA

JWA CARY 68429 Bedienungsanleitung

VIPACK

VIPACK AMORI AMKB9014 Bedienungsanleitung

Rowico

Rowico SANNA Bedienungsanleitung

Southern Enterprises

Southern Enterprises CK556000TX Bedienungsanleitung

hygena

hygena 314/5041 Bedienungsanleitung

VINNOVA

VINNOVA Kinsley 536060S Bedienungsanleitung