Harken 32.2 Two Speed Winch Handbuch

32.2

Two Speed Winch

■Required Tools

Screwdriver

Plastic Head Hammer or Mallet

Small Knife

Brush

Rags

Solvent

Oil

Grease

■Parts List

008 Pawl

038 Pawl Spring

6143 Top Screw

27006 Bearing Spacer

27215 Center Stem

27218 Spindle

27219 Ratchet Gear

27222 Gear Shaft

27560 Pawl Gear

27791 Plastic Washer

27908 Washer

27909 Cover Plate

28168 Red Line Ring

30608 Ratchet Head

703192 Bearing

726073 Bearing

927216 Aluminum Drum

928534 Bronze Drum

■Suggested Service Kits

BK4512 10 008 Pawls

10 038 Springs

BK4513 100 ml Grease

When ordering parts, please

include a “B” before each

number (i.e. B008)

Winch Parts

Installation

Service

■Installing Winch

Make sure mounting surface is flat

Check sheet entry angle. Should be at least 8° (see drawing)

Open winch

Position winch on deck with drive gear where sheet

enters winch drum and mark holes

Remove winch and drill holes

Mount using five (5) 1/4" (6 mm) flathead machine screws

Apply bedding compound and bolt winch to boat

Clean excess bedding compound from base drain holes

Lubricate and close winch

■Opening Winch

Remove top screw

Lift off drum

■Servicing Winch

Remove pawls and springs – service as below

Remove bearings, gear shaft and gears

To reach interior shaft bearing, winch must be removed from deck

Clean all parts with rags and solvent

Use a brush to lubricate all moving parts lightly with grease

Replace pawls and springs and lubricate lightly with oil

Reassemble and close winch

■Servicing Pawls

Catch spring with knife and hold against pawl

Lift out pawls

Clean and check for wear

Lubricate pawls using oil

Place spring against pawl with straight leg against pawl

Hold spring closed and slip pawl into pawl socket

Service winch before the sailing season begins and once during.

USA: 1251 E. Wisconsin Ave., Pewaukee, WI 53072 USA • Tel: (262) 691-3320 • Fax: (262) 691-3008 • Web: harken.com • E-mail: [email protected]

ITALY: Via Della Cerca, 12/14, 22070 Lurago Marinone, Como, Italy • Fax: (39) 031.3520031 • Tel: (39) 031.3523111 • Web: harken.it • E-mail: [email protected]

4464/10-04

Position drive gear where sheet

enters winch drum. Sheet entry angle must be at least

8°.

Clean all parts with solvent.

If ratchet gear is mounted

backwards, winch will slip.

Use a brush to spread a light, even

coat of grease.

Use knife to free captive spring. Insert spring with straight leg against

pawl. Use oil for lubrication.

Mounting

Servicing WinchServicing Pawls

Correct

Incorrect

Andere Harken Winde Handbücher

Harken

Harken 60.3 ST E Handbuch

Harken

Harken Performa Winch 80.3 STP Handbuch

Harken

Harken 40.2 ST EL Series Handbuch

Harken

Harken 53.2ST E/HY Bedienungsanleitung

Harken

Harken 70.2 ST EL Handbuch

Harken

Harken Radial Winch 40.2 PT BBB Handbuch

Harken

Harken 60.3 ST EL Handbuch

Harken

Harken 46.2 ST EL Handbuch

Harken

Harken Performa 20 STP Handbuch

Harken

Harken 46.2 PTBBB Handbuch

Harken

Harken 40.2 PT Handbuch

Harken

Harken Powered Performa Winch 50.2 STP EL Handbuch

Harken

Harken Radial Winch 70.2 ST Handbuch

Harken

Harken Performa Winch 40.2 STP Handbuch

Harken

Harken INLH500KIT.US Bedienungsanleitung

Harken

Harken 40.2ST E Bedienungsanleitung

Harken

Harken Carbo AirBlock 340 Bedienungsanleitung

Harken

Harken Powered Performa 80.3 STP EL/HY Handbuch

Harken

Harken 40.2 ST EL Series Handbuch

Harken

Harken Top-Crank LokHead Rigging Winch 500 Bedienungsanleitung

Harken

Harken Riggers Winch 200 Bedienungsanleitung

Harken

Harken Performa Winch 50.2 PTP Handbuch

Harken

Harken 1130 Betriebsanleitung

Harken

Harken 60.2STEC Handbuch

Beliebte Winde Handbücher anderer Marken

WARRIOR

WARRIOR Trojan 40PUS12 Kurzanleitung

SVERO

SVERO 16 Bedienungsanleitung

Warrior Winches

Warrior Winches C10000NH Bedienungsanleitung

Badland Winches

Badland Winches 68146 Bedienungsanleitung

Bush

Bush II Series Bedienungsanleitung

Badland

Badland APEX 5500 Bedienungsanleitung

Quadratec

Quadratec Q9000 Synthetic Handbuch

C-Max

C-Max VIGO Bedienungsanleitung

Comeup

Comeup DV-9 Bedienungsanleitung

Orvea

Orvea Italwinch 805 Bedienungsanleitung

Prowinch

Prowinch PWJTHF300 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LD2000-A Bedienungsanleitung

Topex

Topex 97X080 Bedienungsanleitung

Eastbound

Eastbound MotoWinch 1707001 Bedienungsanleitung

Runva

Runva EWD8000 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Installationsanleitung

Granit

Granit 11157675 Bedienungsanleitung

TREX

TREX TB75 Bedienungsanleitung