Harken Performa 20 STP Handbuch

Performa™Winch 20 STP

Installation and Maintenance Manual

MRPW-03

Performa™Winch 20 STP

Installation and Maintenance Manual

Index

Introduction 3

Technical characteristics 3

Weight 3

Maximum working load 3

Outline 3

Installation 4

Installation procedure 6

Positioning the self-tailing arm 7

Maintenance 7

Washing 7

Maintenance table 7

Disassembly procedure 7

Exploded view with maintenance products 10

Assembly 11

Harken®limited worldwide warranty 12

Ordering spare parts 12

Exploded view 13

Parts list 15

Performa™Winch 20 STP

Installation and Maintenance Manual

148

Ø73,5

Ø137

Introduction - Technical characteristics - Outline

Introduction

This manual gives technical information on winch installation and maintenance, including

disassembling and reassembling.

This information is DESTINED EXCLUSIVELY for specialised personnel or expert users.

Installation, disassembling and reassembling of the winch by personnel who are not experts may

cause serious damage to users and those in the vicinity of the winch.

Harken®accepts no responsibility for defective installation or reassembly of its winches.

In case of doubt the Harken®Tech Service is at your disposal at techser[email protected]

This Manual is available only in English. If you do not fully understand the English language, do

not carry out the operations described in this Manual.

Technical characteristics

Power ratio Gear ratio

1st speed 19,20 : 1 2,76 : 1

The theoretical power ratio does not take friction into account.

Weight

ST Version

Weight (Kg) 2,4

Maximum working load

WARNING!

The maximum working load (MWL) for the 20 ST Performa™ Winch is 550 Kg (1213 lb)

Subjecting the winch to loads above the maximum working load can cause the winch to fail or

pull off the deck suddenly and unexpectedly during high loads causing severe injury or death.

Outline

Line entry height

Performa™Winch 20 STP

Installation and Maintenance Manual

Installation

The winch must be installed on a at area of the deck, reinforced if necessary to bear a load equal

to at least twice the maximum working load of the winch.

It is the installer's responsibility to carry out all structural tests needed to ensure that the deck can

bear the load.

Harken®does not supply the screws needed to install the winch since these may vary depending

on the deck on which it is to be installed.

It is the installer's responsibility to choose the correct screws taking account of the loads they will

have to bear.

Harken®assumes no responsibility for incorrect installation of its winches or for an incorrect choice

of mounting screws.

DANGER!

Incorrect installation of the winch may cause severe injury or

death. Consult the yard that built the boat in the case of doubt

over the correct positioning of the winch.

WARNING!

Failure to use the correct number and type of mounting fasteners

or failure to ensure the correct deck strength can result in the

winch pulling off the deck suddenly and unexpectedly during

high loads causing severe injury or death.

WARNING!

Verify the entry angle of the sheet. This must be 8° with tolerance

of ±2°, to avoid sheet overrides and damaging the winch or

making the winch inoperable leading to loss of control of the boat

which can lead to severe injury or death.

WARNING!

Mount the winch on the deck so that the drive gear is positioned

where the sheet enters the winch drum.

Incorrect position of drive gear can weaken winch leading to failure

which can cause an accident leading to severe injury or death.

NOTICE

You can find the icon on the skirt to identify the drive gear

position.

Once you have chosen the correct mounting position for the winch on the deck proceed with

installation.

Installation

drive gear

SHEET

8°

Performa™Winch 20 STP

Installation and Maintenance Manual

Procedure

To install the winch you must remove the drum and use Socket Head (SH) bolts.

Tools needed

One medium at-bladed screwdriver

To identify the various parts, refer to the exploded view at the end of this Manual.

Torque to apply when assembling

Install the winch on the deck in the position you have chosen, keeping in mind the limits described

on page 3. (See paragraph on installation)

1. Unscrew the central screw ( 2Nm/18 in-lb)

3. Unscrew the three screws n°16

(4Nm/35 in-lb)

5. Lift off the drum n°13

2. Slide off the socket n°18 and the cover n°17

4. Remove the stripper arm n°15 by

rotating and lifting it.

Performa™Winch 20 STP

Installation and Maintenance Manual

Installation procedure

Carry out the Procedure, then install the winch on the deck in the chosen position.

A. Position the base of the winch on the deck and mark the position of the holes or use the drilling

cut-out template at the point where you have decided to place the winch.

Below is a reduced scale diagram.

The drilling cut out template is available on the Harken®website, www.harken.com

B. Remove the winch and drill the ve 6.2 mm diameter holes.

C. Bolt the base of the winch to the deck using ve M6 bolts (not supplied by Harken®), correctly

chosen for the thickness and type of the boat deck. Consult the yard that built the boat in case of

doubt.

WARNING!

To install the winch on the deck, use only bolts in A4 stainless steel (DIN 267 part11).

Bolts made of other materials may not have sufficient strength or may corrode which can

result in winch pulling off deck suddenly and unexpectedly during high loads causing

severe injury or death.

NOTICE

To mount winches on the deck, do not use countersunk bolts.

D. Fill the mounting holes with a suitable marine sealant.

E. Remove the excess adhesive/sealant from the holes and base drainage channels

Ø110

50°

60°

70°

60°

Ø6.2

n°5

final pinion

position

Winch outside Ø137

Performa™Winch 20 STP

Installation and Maintenance Manual

F. Reassemble the winch following the steps of the Procedure in the reverse order, and apply the

products indicated in the section on maintenance.

NOTICE

Before closing the winch, make sure the holes and drainage channels in the base of the winch

are not obstructed.

Positioning the self-tailing arm

Position the self-tailing arm so that the line leaving the winch is led into the cockpit.

Maintenance

Washing

Winches must be washed frequently with fresh water, and in any case after each use.

Do not allow teak cleaning products or other cleaners containing caustic solutions to come into

contact with winches and especially anodised, chrome plated or plastic parts.

Do not use solvents, polishes or abrasive pastes on the logos, on the stickers on the winches or on

any anodized, chrome plated and plastic surfaces.

Make sure that the holes and drainage channels in the base of the winch are not obstructed so that

water does not collect.

Maintenance table

Winches must be visually inspected at the beginning and end of every season of sailing or racing.

In addition they must be completely overhauled, cleaned and lubricated at least every 12 months.

After an inspection, replace worn or damaged components. Do not replace or modify any part of the

winch with a part that is not original.

WARNING!

Periodic maintenance must be carried out regularly. Lack of adequate maintenance shortens

the life of the winch, can cause serious injury and also invalidate the winch warranty.

Installation and maintenance of winches must be carried out exclusively by specialized

personnel.

In the case of doubt contact Harken®Tech Service at techservice@harken.it

Disassembly procedure

Tools needed

One medium at-bladed screwdriver

A number ve hex key

Rags

To identify the various parts refer to the exploded view at the end of this Manual.

Torque to be applied in assembly phase

Maintenance

Performa™Winch 20 STP

Installation and Maintenance Manual

Carry out procedure as shown in the paragraph on winch installation and then do the following:

6. Completely unscrew the three screws n°16

8. Slide out the central shaft n°7

10. Slide off gear n°3

7. Remove the stripper arm support n°12

and slide out the bushing

9. Remove the pin n°6

11. Slide off gear n°11

Performa™Winch 20 STP

Installation and Maintenance Manual

If it is necessary to replace any jaws of the winch, proceed as follows:

If it is necessary to remove any pawls in the central shaft, proceed as follows:

Once the winch is completely disassembled, clean the parts: use a basin of diesel oil to soak

metal components and rinse plastic parts in fresh water. Once you have done this, dry the parts

with cloths that do not leave residue.

Inspect gears, bearings, pins and pawls for any signs of wear or corrosion.

Carefully check the teeth of gears and ring gears to make sure there are no traces of wear.

Replace worn or damaged components.

Carry out maintenance on components using the products listed below.

For more information on which products to use where, refer to the exploded diagram below.

Use a brush to lightly lubricate all gears, gear pins, teeth and all moving parts with grease.

Lightly lubricate the pawls and springs with oil. Do not use grease on the pawls!

I. Unscrew the 3 screws n°14

(4Nm/35 in-lb)

Unscrew the screw n°10 and remove

the washer n°9 ( 4Nm/35 in-lb)

II. Remove the jaws n°19

Performa™Winch 20 STP

Installation and Maintenance Manual

Exploded view with maintenance products

1Apply Harken®grease on assy socket screw

2Apply Harken®grease on drum gear

Harken®Grease

Harken®Pawl Oil

Axial Threadlocker

Anti-seize

Inhaltsverzeichnis

Andere Harken Winde Handbücher

Harken

Harken Top-Crank LokHead Rigging Winch 500 Bedienungsanleitung

Harken

Harken 40.2 ST EL Series Handbuch

Harken

Harken 20.2 PTBBB Handbuch

Harken

Harken Carbo AirBlock 340 Bedienungsanleitung

Harken

Harken NAUTOR MKIV C8436 Bedienungsanleitung

Harken

Harken Performa Winch 80.2 STP Handbuch

Harken

Harken CLR 600 Handbuch

Harken

Harken 48.2ST E/HY Bedienungsanleitung

Harken

Harken 53.2 Bedienungsanleitung

Harken

Harken 40.2 ST EL Series Handbuch

Harken

Harken 56.2ST E/HY Bedienungsanleitung

Harken

Harken Powered Performa 80.3 STP EL/HY Handbuch

Harken

Harken LokHead 500 KIT.US Bedienungsanleitung

Harken

Harken UniPower Radial Handbuch

Harken

Harken 16.2 Two Speed Winch Handbuch

Harken

Harken Performa 46.2 STP Handbuch

Harken

Harken Performa 60.2 STP EL/HY Handbuch

Harken

Harken Performa Winch 40.2 STP Handbuch

Harken

Harken Riggers Winch 200 Bedienungsanleitung

Harken

Harken B 1140 Series Bedienungsanleitung

Harken

Harken 46.2 Kurzanleitung

Harken

Harken Performa Winch 40.2 PTP Handbuch

Harken

Harken 50.2 PTBBB Handbuch

Harken

Harken 46.2ST E/HY Bedienungsanleitung

Beliebte Winde Handbücher anderer Marken

WARRIOR

WARRIOR Trojan 40PUS12 Kurzanleitung

SVERO

SVERO 16 Bedienungsanleitung

Warrior Winches

Warrior Winches C10000NH Bedienungsanleitung

Badland Winches

Badland Winches 68146 Bedienungsanleitung

Bush

Bush II Series Bedienungsanleitung

Badland

Badland APEX 5500 Bedienungsanleitung

Quadratec

Quadratec Q9000 Synthetic Handbuch

C-Max

C-Max VIGO Bedienungsanleitung

Comeup

Comeup DV-9 Bedienungsanleitung

Orvea

Orvea Italwinch 805 Bedienungsanleitung

Prowinch

Prowinch PWJTHF300 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LD2000-A Bedienungsanleitung

Topex

Topex 97X080 Bedienungsanleitung

Eastbound

Eastbound MotoWinch 1707001 Bedienungsanleitung

Runva

Runva EWD8000 Kurzanleitung

Ingersoll-Rand

Ingersoll-Rand LIFTSTAR FG 1500/CN Series Installationsanleitung

Granit

Granit 11157675 Bedienungsanleitung

TREX

TREX TB75 Bedienungsanleitung