Harman JBL BAR 2.1 DEEP BASS Bedienungsanleitung

BAR 2.1 DEEP BASS

OWNER’S MANUAL

JBL_SB_Bar 2.1_OM_V3.indd 1 7/4/2019 3:26:40 PM

IMPORTANT SAFETY INSTRUCTIONS

Verify Line Voltage Before Use

The JBL Bar 2.1 Deep Bass (soundbar and subwoofer) has

been designed for use with 100-240 volt, 50/60 Hz AC current.

Connection to a line voltage other than that for which your

product is intended can create a safety and re hazard and may

damage the unit. If you have any questions about the voltage

requirements for your specic model or about the line voltage in

your area, contact your retailer or customer service representative

before plugging the unit into a wall outlet.

Do Not Use Extension Cords

To avoid safety hazards, use only the power cord supplied

with your unit. We do not recommend that extension cords be

used with this product. As with all electrical devices, do not run

power cords under rugs or carpets, or place heavy objects on

them. Damaged power cords should be replaced immediately

by an authorized service center with a cord that meets factory

specications.

Handle the AC Power Cord Gently

When disconnecting the power cord from an AC outlet, always

pull the plug; never pull the cord. If you do not intend to use this

speaker for any considerable length of time, disconnect the plug

from the AC outlet.

Do Not Open the Cabinet

There are no user-serviceable components inside this product.

Opening the cabinet may present a shock hazard, and any

modication to the product will void your warranty. If water

accidentally falls inside the unit, disconnect it from the AC power

source immediately, and consult an authorized service center.

JBL_SB_Bar 2.1_OM_V3.indd 2 7/4/2019 3:26:40 PM

www.jbl.com

English

TABLE OF CONTENTS

IMPORTANT SAFETY INSTRUCTIONS 2

1 INTRODUCTION 4

2 WHAT’S IN THE BOX 4

3 PRODUCT OVERVIEW 5

3.1 SOUNDBAR 5

3.2 SUBWOOFER 5

3.3 REMOTE CONTROL 6

4 PLACE 6

4.1 DESKTOP PLACEMENT 6

4.2 WALL-MOUNTING 7

5 CONNECT 7

5.1 TV CONNECTION 7

5.2 DIGITAL DEVICE CONNECTION 8

5.3 BLUETOOTH CONNECTION 8

6 PLAY 9

6.1 POWER-ON/AUTO STANDBY/AUTO WAKEUP 9

6.2 PLAY FROM THE TV SOURCE 9

6.3 PLAY FROM THE HDMI IN SOURCE 10

6.4 PLAY FROM THE BLUETOOTH SOURCE 10

7 SOUND SETTINGS 10

8 RESTORE FACTORY SETTINGS 11

9 SOFTWARE UPDATE 11

10 RE-CONNECT THE SUBWOOFER 11

11 PRODUCT SPECIFICATIONS 12

12 TROUBLESHOOTING 12

13 TRADEMARKS 13

14 OPEN SOURCE LICENSE NOTICE 14

JBL_SB_Bar 2.1_OM_V3.indd 3 7/4/2019 3:26:40 PM

1 INTRODUCTION

Thank you for purchasing the JBL Bar 2.1 Deep Bass (soundbar

and subwoofer) which is designed to bring an extraordinary sound

experience to your home entertainment system. We encourage

you to take a few minutes to read through this manual, which

describes the product and includes step-by-step instructions for

setting up and getting started.

To make the most of product features and support, you

may need to update the product software through the USB

connector in the future. Refer to the software update section

in this manual to ensure that your product has the latest

software.

Designs and specications are subject to change without notice.

If you have any questions about the soundbar, installation or

operation, please contact your retailer or customer service

representative, or visit our website: www.jbl.com.

2 WHAT’S IN THE BOX

Unpack the box carefully and ensure that the following parts are

included. If any part is damaged or missing, do not use it and

contact your retailer or customer service representative.

Soundbar

Subwoofer

Remote control (with 2 AAA batteries)

Power cord*

x 2

* Power cord and plug type vary region.

HDMI cable

Wall-mounting kit

Product information quantity & wall-mounting template

JBL_SB_Bar 2.1_OM_V3.indd 4 7/4/2019 3:26:40 PM

www.jbl.com

English

3 PRODUCT OVERVIEW

3.1 Soundbar

Controls

1 32

1. (Power)

• Switch on or to standby

2. -/+ (Volume)

• Decrease or increase the volume

• Press and hold to decrease or increase the volume

continuously

• Press the two buttons together to mute or unmute

3. (Source)

• Select a sound source: TV (default), Bluetooth or HDMI

4. Status display

Connectors

1 2 3 4 5

1. POWER

• Connect to power

2. OPTICAL

• Connect to the optical output on your TV or digital device

3. USB

• USB connector for software update

• Connect to a USB storage device for audio play (for US

version only)

4. HDMI IN

• Connect to the HDMI output on your digital device

5. HDMI OUT (TV ARC)

• Connect to the HDMI ARC input on your TV

3.2 Subwoofer

• Connection status indicator

Solid white Connected to the soundbar

Flashing white Pairing mode

Solid amber Standby mode

2. POWER

• Connect to power

JBL_SB_Bar 2.1_OM_V3.indd 5 7/4/2019 3:26:40 PM

3.3 Remote control

• Switch on or to standby

2. TV

• Select the TV source

3. (Bluetooth)

• Select the Bluetooth source

• Press and hold to connect another Bluetooth device

• Select the bass level for subwoofer: low, middle, or high

5. HDMI

• Select the HDMI IN source

6. + / -

• Increase or decrease the volume

• Press and hold to increase or decrease the volume

continuously

7. (Mute)

• Mute/unmute

4 PLACE

4.1 Desktop placement

Place the soundbar and subwoofer on a at and stable surface.

Make sure that the subwoofer is at least 3 ft (1 m) away from the

soundbar, and 4” (10 cm) away from a wall.

> 10cm/4”

1m/3ft

NOTES:

−The power cord shall be properly connected to power.

−Do not place any objects on the top of the soundbar or subwoofer.

−Make sure that the distance between the subwoofer and the soundbar

is less than 20 ft (6 m).

JBL_SB_Bar 2.1_OM_V3.indd 6 7/4/2019 3:26:41 PM

www.jbl.com

English

4.2 Wall-mounting

≤8 mm/

0.31"

4mm/

0.16"

≥30 mm/1.18"

1. Preparation:

a) With a minimum distance of 2” (50mm) from your TV, stick

the supplied wall-mounting template to a wall by using

adhesive tapes.

b) Use your ballpen tip to mark the screw holder location.

Remove the template.

c) On the marked location, drill a 4 mm/0.16” hole. Refer to

Figure 1 for the screw size.

2. Install the wall-mounting bracket.

3. Fasten the screw onto the back of the soundbar.

4. Mount the soundbar.

NOTES:

−Make sure that the wall can support the weight of the soundbar.

−Install on a vertical wall only.

−Avoid a location under high temperature or humidity.

−Before wall-mounting, make sure that cables can be properly

connected between the soundbar and external devices.

−Before wall-mounting, make sure that the soundbar is unplugged from

power. Otherwise, it may cause an electric shock.

5 CONNECT

5.1 TV connection

Connect the soundbar with your TV through the supplied HDMI

cable or an optical cable (sold separately).

Through the supplied HDMI cable

An HDMI connection supports digital audio and video with a

single connection. HDMI connectivity is the best option for your

soundbar.

HDMI

(ARC)

HDMI OUT

(TV ARC)

1. Connect the soundbar with your TV by using the supplied

HDMI cable.

2. On your TV, check that HDMI-CEC and HDMI ARC have been

enabled. Refer to the owner’s manual of your TV for more

information.

NOTES:

−Full compatibility with all HDMI-CEC devices is not guaranteed.

−Contact your TV manufacturer if you have problems with the HDMI-

CEC compatibility of your TV.

Through an optical cable

OPTICAL

• Connect the soundbar with your TV by using an optical cable

(sold separately).

JBL_SB_Bar 2.1_OM_V3.indd 7 7/4/2019 3:26:41 PM

5.2 Digital device connection

1. Make sure that you have connected your TV to the soundbar

through the HDMI ARC connection (See “Through the supplied

HDMI cable” under “TV connection” in the “CONNECT”

chapter).

2. Use an HDMI cable (V1.4 or later) to connect the soundbar

with your digital device, such as a set-top box, DVD/Blu-ray

player or game console.

3. On your digital device, check that HDMI-CEC has been

enabled. Refer to the owner’s manual of your digital device for

more information.

HDMI IN

HDMI OUT

NOTES:

−Contact your digital device manufacturer if you have problems with the

HDMI-CEC compatibility of your digital device.

5.3 Bluetooth connection

Through Bluetooth, connect the soundbar with your Bluetooth

device, such as a smartphone, tablet and laptop.

Settings Bluetooth

Bluetooth

DEVICES

JBL Bar 2.1

Now Discoverable

Connected

< 10 m / 33 ft

Connect a Bluetooth device

1. Press to switch on (See “Power-on/Auto standby/Auto

wakeup” in the “PLAY” chapter).

2. To select Bluetooth source, press on the soundbar or on

the remote control.

→“BT PAIRING”: Ready for BT pairing

3. On your Bluetooth device, enable Bluetooth and search for

“JBL Bar 2.1” within three minutes.

→The device name is displayed if your device is named in

English. A conrmation tone is heard.

To reconnect the last paired device

Your Bluetooth device is retained as a paired device when the

soundbar goes to standby mode. Next time you switch to the

Bluetooth source, the soundbar reconnects the last paired device

automatically.

To connect to another Bluetooth device

1. In the Bluetooth source, press and hold on the soundbar

or on the remote control until “BT PAIRING” is displayed.

→The previously paired device is cleared from the soundbar.

→The soundbar enters the Bluetooth pairing mode.

2. Follow the Step 3 under “Connect a Bluetooth device”.

• If the device has ever been paired with the soundbar, rst

unpair “JBL Bar 2.1” on the device.

NOTES:

−The Bluetooth connection will be lost if the distance between the

soundbar and Bluetooth device exceeds 33 ft (10 m).

−Electronic devices may cause radio interference. Devices that generate

electromagnetic waves must be kept away from the Soundbar, such

as microwaves and wireless LAN devices.

JBL_SB_Bar 2.1_OM_V3.indd 8 7/4/2019 3:26:41 PM

www.jbl.com

English

6 PLAY

6.1 Power-on/Auto standby/Auto wakeup

POWER

Switch on

1. Connect the soundbar and subwoofer to power by using the

supplied power cords.

2. On the soundbar, press to switch on.

→“HELLO” is displayed.

→The subwoofer is connected to the soundbar automatically.

Connected: turns solid white.

NOTES:

−Use the supplied power cord only.

−Before switching on the soundbar, make sure that you have completed

all other connections (See “TV connection” and “Digital device

connection” in the “Connect” chapter).

Auto standby

If the soundbar is inactive for more than 10 minutes, it will switch

to standby mode automatically. “STDBY” is displayed. The

subwoofer also goes to standby, and turns solid amber.

Next time you switch on the soundbar, it returns to the last

selected source.

Auto wakeup

In standby mode, the soundbar will wake up automatically when

• the soundbar is connected to your TV through the HDMI

ARC connection and your TV is switched on;

• the soundbar is connected to your TV through an optical

cable and audio signals are detected from the optical cable.

6.2 Play from the TV source

With the soundbar connected, you can enjoy TV audio from the

soundbar speakers.

HDMI ARC

OPTICAL

1. Make sure that your TV is set to support external speakers

and the built-in TV speakers are disabled. Refer to the owner’s

manual of your TV for more information.

2. Make sure that the soundbar has been properly connected

to your TV (See “TV connection” in the “CONNECT” chapter).

3. To select the TV source, press on the soundbar or TV on

the remote control.

→“TV”: The TV source is selected.

• In the factory settings, the TV source is selected by

default.

NOTES:

−If the soundbar is connected to your TV through both an HDMI cable

and an optical cable, the HDMI cable is selected for the TV connection.

6.2.1 TV remote control setup

To use your TV remote control for both your TV and the soundbar,

check that your TV supports HDMI-CEC. If your TV does not

support HDMI-CEC, follow the steps under “TV remote control

learning”.

HDMI-CEC

If your TV supports HDMI-CEC, enable the functions as instructed

in your TV user manual. You can control the volume +/-, mute/

unmute, and power on/standby functions on your soundbar

through the TV remote control.

TV remote control learning

1. On the soundbar, press and hold and + until “LEARNING”

is displayed.

→You enter the TV remote control learning mode.

2. Within 15 seconds, do the following on the soundbar and your

TV remote control:

a) On the soundbar: press one of the following buttons +, -,

+and - together (for the mute/unmute function), and .

b) On your TV remote control: press the desired button.

→“WAIT” is displayed on the soundbar.

→“DONE”: The function of the soundbar button is learnt

by your TV remote control button.

3. Repeat Step 2 to complete the button learning.

JBL_SB_Bar 2.1_OM_V3.indd 9 7/4/2019 3:26:41 PM

4. To exit the TV remote control learning mode, press and hold

and + on the soundbar until “EXIT LEARNING” is displayed.

→The soundbar returns to the last selected source.

6.3 Play from the HDMI IN source

With the soundbar connected as shown in the following diagram,

your digital device can play video on your TV and audio from the

soundbar speakers.

HDMI IN

HDMI OUT

(TV ARC)

HDMI OUT

HDMI

(ARC)

1. Make sure that the soundbar has been properly connected to

your TV and digital device (See “TV connection” and “Digital

device connection” in the “CONNECT” chapter).

2. Switch on your digital device.

→Your TV and the soundbar wake up from standby mode

and switch to the input source automatically.

• To select the HDMI IN source on the soundbar, press

on the soundbar or HDMI on the remote control.

3. Switch your TV to standby mode.

→The soundbar and source device are switched to standby

mode.

NOTES:

−Full compatibility with all HDMI-CEC devices is not guaranteed.

6.4 Play from the Bluetooth source

Through Bluetooth, stream audio play on your Bluetooth device

to the soundbar.

1. Check that the soundbar has been properly connected to

your Bluetooth device (See “Bluetooth connection” in the

“CONNECT” chapter).

2. To select the Bluetooth source, press on the soundbar or

on the remote control.

3. Start audio play on your Bluetooth device.

4. Adjust the volume on the soundbar or your Bluetooth device.

7 SOUND SETTINGS

Bass adjustment

1. Check that the soundbar and subwoofer are properly

connected (See the “INSTALL” chapter).

2. On the remote control, press repeatedly to switch between

bass levels.

→“LOW”, “MID” and “HIGH” are displayed.

Audio sync

With the audio sync function, you can synchronize audio and

video to make sure that no delay is heard from your video content.

1. On the remote control, press and hold TV until “SYNC” is

displayed.

2. Within ve seconds, press +or - on the remote control to

adjust the audio delay and match with video.

→The audio sync timing is displayed.

Smart mode

With the smart mode enabled by default, you can enjoy TV

programs with rich sound effects. For TV programs such as news

and weather forecasts, you can reduce sound effects by disabling

the smart mode and switching to the standard mode.

Smart mode: EQ settings and JBL Surround Sound are applied

for rich sound effects.

Standard mode: The preset EQ settings are applied for standard

sound effects.

To disable the smart mode, do the following:

• On the remote control, press and hold until “TOGGLE” is

displayed. Press +.

→“OFF SMART MODE”: The smart mode is disabled.

→Next time you switch on the soundbar, the smart mode is

enabled again automatically.

JBL_SB_Bar 2.1_OM_V3.indd 10 7/4/2019 3:26:42 PM

Andere Handbücher für JBL BAR 2.1 DEEP BASS

Inhaltsverzeichnis

Andere Harman Sprecher Handbücher

Harman

Harman JBL Conceal Series Bedienungsanleitung

Harman

Harman JBL IRX108-BT Bedienungsanleitung

Harman

Harman JBL FLIP 5 Bedienungsanleitung

Harman

Harman JBL Club 34F Bedienungsanleitung

Harman

Harman CITATION TOWER Bedienungsanleitung

Harman

Harman JBL SoundPoint SP8 Series Bedienungsanleitung

Harman

Harman Harman Kardon CITATION ONE Bedienungsanleitung

Harman

Harman JBL CINEMA SB190 Bedienungsanleitung

Harman

Harman JBL VerTec VT4889ADP Technisches Datenblatt

Harman

Harman JBL CINEMA SB160 Bedienungsanleitung

Harman

Harman JBL BAR 2.1 DEEP BASS MK2 Bedienungsanleitung

Harman

Harman JBL LINK 300 Bedienungsanleitung

Harman

Harman AXYS TUNNEL Intellivox ADC-V90 Bedienungsanleitung

Harman

Harman JBL FLIP Bedienungsanleitung

Harman

Harman JBL FLIP 4 Bedienungsanleitung

Harman

Harman TRAVELER Bedienungsanleitung

Harman

Harman Martin P3 PowerPort 1000 IP Bedienungsanleitung

Harman

Harman axys ABF-260 Bedienungsanleitung

Harman

Harman JBL Professional EON700 Series Bedienungsanleitung

Harman

Harman JBL XTREME 2 Bedienungsanleitung

Harman

Harman JBL QUANTUM Stream Bedienungsanleitung

Harman

Harman JBL Professional VTX Series Bedienungsanleitung

Harman

Harman JBL Charge4 Bedienungsanleitung

Harman

Harman JBL FLIP ESSENTIAL 2 Bedienungsanleitung

Beliebte Sprecher Handbücher anderer Marken

argon audio

argon audio IE20 Bedienungsanleitung

Denon

Denon SC-N7 Bedienungsanleitung

Gemline

Gemline Ace 3952 Bedienungsanleitung

Focal

Focal ON WALL 300 Bedienungsanleitung

HEADRUSH

HEADRUSH Maximus HRSP 5024 Bedienungsanleitung

SoundLogic

SoundLogic BCCS-6/6395 Bedienungsanleitung

Peavey

Peavey DTH 218 Bedienungsanleitung

Avantree

Avantree Pluto Air Bedienungsanleitung

Morel

Morel Integra Series INTEGRA OVATION 4 Bedienungsanleitung

Oppo

Oppo SONICA Bedienungsanleitung

Bose

Bose SoundLink Wireless Music System Bedienungsanleitung

Rocksteady

Rocksteady Stadium Bedienungsanleitung

Bowers & Wilkins

Bowers & Wilkins 4 Bedienungsanleitung

Sonance

Sonance SONOS OUTDOOR Series Bedienungsanleitung

Electro-Voice

Electro-Voice EVID FM4.2 Bedienungsanleitung

Pioneer

Pioneer XW-HTD630 Bedienungsanleitung

Onn

Onn BWA16AA002 Bedienungsanleitung

HP GL313AA - USB Speakers PC Multimedia Bedienungsanleitung