Harman Magnum Stoker Bedienungsanleitung

























MGMR13











DO NOT BURN WET COAL



Introduction 3

Warnings 3

Packing List 5

Assembly 6

Installation 10

Verti-Flow Stoker Control 14

Operation 15

Maintenance 18

Trouble-Shooting 21

Wiring Diagram 23

Feeder Parts 24

Domestic Hot Water Coil 25

Hot Air Duct Option 26

Warranty 27

DO NOT BURN WET COAL





This proven design by Harman features the Verti-Flow Stoker

System.

This unique system provides a very wide range of heat output.

The Verti-Flow Stoker can operate from 5000 to over 85,000 btu's

automatically.

This unit has a 100 pound coal capacity and can provide 85,000

btu's continuous for 17 hours or stretch out to over 100 hours

when less heat is required.

A thermostat is used to regulate the heat output of the stove.

When no heat is needed, the stoker stops and only runs to maintain

the re. If heat is needed, the thermostat can turn on the stoker

at any time.

The pilot or maintenance mode is controlled by a timer box. The

"on" and "off" time can be changed to provide more or less heat

during the maintenance cycle, and to adjust for different coal quality.

This unit must be connected to a chimney capable of providing

a .04 minimum draft reading.  If the chimney has

no draft, coal gases may escape from the unit and stovepipe.

 It is recommended that

a carbon monoxide detector be installed to warn of this condition.









This unit has been tested and approved by OMNI-TEST

Laboratories in accordance to the listed codes. This appliance

is also approved for installation into a shop.

DO NOT BURN WET COAL























Freshly delivered coal is watered down to

eliminate dust when loading and unloading. Wet

rice coal does not ow as well as damp or dry

coal. We do not recommend burning wet coal,

however, we realize if it's the only coal you have

it is better to burn it than freeze. If you must burn

wet coal, the feed rate must be increased in

order to get the same size re. As the wet coal

in the hopper dries out, the feed rate must be

decreased. If you don’t, the feeder will over-re

the stove and waste coal. Doing this once or

twice a year will not damage your stove as long

as it is hot and burning. The damage is caused

when the hopper has wet coal in it when the

stove is cold. This will cause rust and corrosion

which is not covered by your warranty.

Usually after the coal dries for three or four

days, depending on conditions, it will ow very

well and feed properly. The feed rate will then

be the same as for dry coal.

    





      





DO NOT BURN WET COAL



DO NOT BURN WET COAL



First, a note to you, the customer.

This section on Assembly is in the manual for

your information should you ever need to move

your unit and to help you understand how each

part is installed.

Harman Home Heating recommends that your

dealer complete the assembly of this stove. It is

also recommended to take a draft reading with the

stoker burning. This reading should be recorded

on the warranty coupon when you activate your

warranty.



Begin assembly by sliding the pusher block with

the adjuster rod from the front through the slot

shown in g.1. Be sure the pusher block is turned

with the bolt hole to feed indicator side.

Next, hold the pusher block in the most rearward

position and slide the adjuster tube over the adjuster

rod until it bottoms out on the pusher block. Thread

the adjuster over the adjuster rod. Thread wing nut

onto the end of the adjuster rod.

DO NOT BURN WET COAL

Make sure the gasket is in place on the feeder

opening on the rear of the unit, as shown in g 3.

Insert the stoker into the opening in the rear of the

unit. Attach using (2) 5/16 X 1 1/4 bolts.



Install the smaller of the two blowers on the bottom

of the feeder by sliding it into the bracket as far as

it will go. Install restricter plate on blower as shown

below in Fig. 4.

Slide the larger blower into place on the bottom

rear of the stove. NOTE: The bolt holes on the

blowers are not used.



Install the control box on mounting pad provided on

the side of the stoker with (4) #8-32 bolts. NOTE:

The receptacles go toward the front.

Plug the gear motor into the top, the small

combustion blower into the middle, and the large

distribution blower into the bottom receptacle on

the control box as shown. More on the control later.



Install scraper as shown below with locking nut

on each side of the scraper. Tighten nuts when in

the rear most position to assure alignment. Cycle

rod in and out to clean unit.

DO NOT BURN WET COAL

IMPORTANT

Be sure the grate holder is centered

and back as far as possible.



Install hopper support on top rear of stoker.

Note that the bolt holes in the hopper support are slotted

for adjustment. Insert the funnel end of hopper into the

hopper slot on the feeder as shown. Push the top of the

hopper under the hopper support, causing the slot on the

bottom side of the support to hook onto the hopper. The

hopper support will spring up slightly for the hopper to

go under. If you have difculty getting the hopper under,

adjustment may be necessary. Use slotted holes shown

at left. Now the feed motor cover can be installed.



The grate is composed of four pieces: the grate holder, (2)

grate inserts, and grate angle. The grate angle is bolted

to the grate holder with (2) 3/8 X 1 1/4 bolts. Before

installing the grate holder, the 3/8" round gasket must

be checked in the groove on the bottom side of the grate

holder, as shown in g. 7. Check to be sure the gasket

has not been damaged.

The grate holder must be installed through the top door

opening after the feeder has been installed.

Locate the ange at the rear of the grate holder into the

slot on the feeder as shown below. Bolt the front end down

with the 1/4 x 20 Allen bolt and nut provided. The rear end

will be locked in place by the ange. Before tightening the

bolt be sure the grate holder is back as far as possible

and centered side to side on the feeder opening.

Install grate inserts as shown at left. Divide the spaces

between the inserts equally and be sure they are not tight.

The spaces are needed for expansion.

DO NOT BURN WET COAL



Lay the glass frame face down on a at surface. The glass panel

should have channel gasket on the ends (short sides) only. Place

the glass panel into the frame, making sure that it is completely

down in the frame. Now lay the door onto the frame and secure

it using four 1/4-20 ange head bolts. With the assembled door

still lying face down, slide the door top trim under the top of the

door. Align the holes and secure the top trim using two 1/4-20 hex

head bolts.

Door Top Trim

Glass Frame

Bolt Locations

Door Top Trim

Bolt Locations

Front View

DO NOT BURN WET COAL

IMPORTANT

Use only U.L. approved oor board

 





Place the stove a minimum of 3" from a combustible

wall from the rear of the hopper and a minimum of

24" from the sides. The stove should be placed

on a noncombustible oor, or a minimum 3/8" thick

noncombustible oor protector. Install a 6" stove

pipe from ue opening to chimney with a barometric

damper. Secure all pipe joints with sheet metal

screws. Plug power cord into a 120 volt receptacle.

Refer to the section on operation to light a re. With

the stove burning and stabilized, set barometric

damper at .04 to .06 on the draft meter. We do not

expect you to own a draft meter. Therefore, have

your dealer do set-up and ne tuning.

If your chimney will not produce .04 on the draft

meter, a draft inducer should be installed by your

dealer. The draft inducer may help to provide the

additional draft needed for proper operation. If not,

the chimney will need to be corrected.

Inhaltsverzeichnis

Andere Harman Herd Handbücher

Harman

Harman Super-Magnum Coal Stoker Stove Sicherheitsleitfaden

Harman

Harman Absolute 43 Bedienungsanleitung

Harman

Harman XXV-TC Bedienungsanleitung

Harman

Harman P43 Bedienungsanleitung

Harman

Harman Absolute63 Bedienungsanleitung

Harman

Harman SF 250 Montageanleitung

Harman

Harman Super-Magnum Bedienungsanleitung

Harman

Harman Accentra Montageanleitung

Harman

Harman P43 Bedienungsanleitung

Harman

Harman Allure50 Bedienungsanleitung

Harman

Harman TLC 2000 Montageanleitung

Harman

Harman DVC-500 Montageanleitung

Harman

Harman Oakleaf Wood Stove Bedienungsanleitung

Harman

Harman CW-30 Montageanleitung

Harman

Harman Magnafire MARK I Bedienungsanleitung

Harman

Harman Oakwood Montageanleitung

Harman

Harman P43 Bedienungsanleitung

Harman

Harman XXV Bedienungsanleitung

Harman

Harman Mark I Bedienungsanleitung

Harman

Harman P43-C Bedienungsanleitung

Harman

Harman P42i-TC Bedienungsanleitung

Harman

Harman PC45 Bedienungsanleitung

Harman

Harman XXV-TC Bedienungsanleitung

Harman

Harman P61-C Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung

Barton

Barton FH-AMP8745 Technisches Dokument