Hasbro LAZER TAG 13744 Bedienungsanleitung

LT01_distressed

LT02_clean

AGES 8+

13744

Replace with 12 x 1.5V “AA” or R6 size alkaline batteries.

Phillips/cross head screwdriver (not included) needed to

replace batteries.

BATTERIES INCLUDED

x12

Get other manuals https://www.bkmanuals.com

STANDARD, CRT TV ONLY. NOT FOR USE WITH PROJECTION, LCD,

HIGH-DEFINITION, OR PLASMA TV.

1. Using a Phillips/cross head screwdriver (not

included), unscrew the battery covers on

your Tagger units.

2. Insert 6 fresh 1.5 V “AA” or R6 size

batteries (not included) in each Tagger

unit. Alkaline batteries recommended. See

diagram for polarity.

3. Replace battery covers and tighten screws.

Replacing the batteries:

Get other manuals https://www.bkmanuals.com

CAUTION: TO AVOID BATTERY LEAKAGE

1. Be sure to insert the batteries correctly and always follow the toy and battery

manufacturers’ instructions;

2. Do not mix old and new batteries or alkaline, standard (carbon-zinc) or

rechargeable (nickel-cadmium) batteries;

3. Always remove weak or dead batteries from the product.

IMPORTANT: BATTERY INFORMATION

Please retain this information for future reference.

Batteries should be replaced by an adult.

CAUTION:

1. Always follow the instructions carefully. Use only batteries specified and be sure

to insert item correctly by matching the + and – polarity markings.

2. Do not mix old and new batteries or standard (carbon-zinc) with alkaline

batteries.

3. Remove exhausted or dead batteries from the product.

4. Remove batteries if product is not to be played with for a long time.

5. Do not short-circuit the supply terminals.

6. Should this product cause, or be affected by, local electrical interference, move

it away from other electrical equipment. Reset (switching off and back on again

or removing and reinserting batteries) if necessary.

7. RECHARGEABLE BATTERIES: Do not mix these with any other types of

batteries. Always remove from the product before recharging. Recharge batteries

under adult supervision. DO NOT RECHARGE OTHER TYPES OF BATTERIES.

Get other manuals https://www.bkmanuals.com

THE PARTS OF YOUR TAGGER

Power/Game

Type Switch

Strength Switch

Accessory Rail

Indoor/Outdoor Switch

VIDEO GAME MODULE

PINPOINT SIGHT

Release Button

SHOT BLAST™*

Attachment

Weapon Rail

Shield Activation

Button

Trigger

Receiver Dome/Hit Indicator

Ammo Core™*

Release

Strength

Gauge

Ammo

Indicator

Ammo Core™*

Rack

Get other manuals https://www.bkmanuals.com

1. All players should agree on Strength scores for the

game, and set the Strength Switch to either 10 or

25. You can’t change your Strength score once the

game begins!

• 10 Strength means you can be tagged 10 times

before you are out of the game.

• 25 Strength means you can be tagged 25 times

before you are out of the game. Your Strength

Gauge will stay ﬁlled until you are on your last 10

Strength points.

2. Set the Indoor/Outdoor Switch to the proper

position based on where you are.

3. Decide what game type to play – Solo or Team.

• Solo Game means that all players are on their

own. The last player with any Strength Points left

wins!

• Team Game means that players organize

themselves into two teams that battle against each

other. You can’t tag someone on your own team.

There are many different team games you can play

– make up your own, or check out lazertag.com for

team game rules!

BEFORE YOU TURN ON YOUR TAGGER

Get other manuals https://www.bkmanuals.com

1. Switch your Tagger to Solo, Team 1 or Team 2.

2. When all players have set their Taggers to the right

game type, point your Tagger in the air and pull the

Trigger. This will activate a 10-second countdown,

after which the game begins!

3. To tag another Player, point your Tagger at him and

pull the Trigger. This will use one round of Ammo.

4. When all of the lights on the Ammo Indicator are out,

you need to reload. Press the Ammo Core™* Release

to pop out the Ammo Core™*. Now, push the Power

Core back in. You are reloaded and ready to continue

tagging!

5. When you are tagged, your Tagger will rumble, and

one (or more, depending on the Weapon Accessory

your opponent is using) of your Strength points will

be lost. When all of the lights on your Strength Gauge

go out, you are out of the game (your Tagger will warn

you when your Strength is down to dangerous levels).

6. The last player (or players on the same team in a

team game) with Strength points left wins!

PLAYING A GAME

Note: You have ten rounds

of Ammo after each

reload. When you ﬁre one

round, one of the lights on

your Ammo Indicator will

blink. When you ﬁre the

second, the blinking light

will go out.

.com

The PHOENIX LTX™* Tagger is compatible with all LAZER TAG

Team Ops gear from TIGER ELECTRONICS™* and HASBRO®*.

See for more details.

Get other manuals https://www.bkmanuals.com

When your shield is active, you

cannot be tagged, but you also can’t

tag anyone.

1. To activate your Shields, press and

hold the Shield Activation Button.

2. The shield will stay on for up to

10 seconds. You will hear it power

up and hum. While your shield is

up, you cannot tag or be tagged.

3. After you release the Shield

Activation Button, you will hear

your shield power down. You are

now vulnerable to tags, and can

tag other players.

4. You must wait 2 seconds before

activating your shields again.

5. You only have a few seconds of

shield charge per game, so use

them wisely!

USING THE SHIELDS

You get 15

seconds of

Shields during

a 10 Strength

game.

You get 30

seconds of

Shields during

a 25 Strength

game.

Get other manuals https://www.bkmanuals.com

1. Slide the PINPOINT SIGHT onto the accessory rail

on the top of your Tagger until it locks into place.

2. Look into the PINPOINT SIGHT. If it is properly

attached, you will see a green dot reﬂected on the

crosshairs.

3. Line up the green dot in the center of the

crosshairs with your target for pinpoint accuracy!

USING THE SHOT BLAST™* WEAPON ACCESSORY

Note: Tags ﬁred by the

SHOT BLAST accessory

have a shorter range than

regular tags, but affect a

wider area. If you catch

several opponents standing

close to one another, you

can actually hit all of them

at once!

USING THE PINPOINT SIGHT

1. Slide the SHOT BLAST accessory onto the

front of the Tagger until it snaps into place.

2. To arm the SHOT BLAST, slide the Rack

toward you, and then forward again.

3. When you pull the trigger, your Tagger will ﬁre

an extra-powerful blast. Depending on how

accurate your shot is, you could take as many

as three points off your target’s Strength

Gauge.

4. You will need to Rack the SHOT BLAST again

before you can ﬁre it.

5. If you pull the Trigger without using the Rack,

you will ﬁre a single, regular Tagger shot.

6. To remove the SHOT BLAST, slide the

Release Button down and pull it off

the Tagger.

Get other manuals https://www.bkmanuals.com

Slide the Video Game Module onto the

accessory rail on the front of your Tagger,

until it locks into place.

To remove it, slide the Release Button

down and pull the Module off the Tagger.

USING THE VIDEO GAME MODULE

Plug it in, and experience intense, single-player Lazer Tag action on your television!

REQUIREMENTS

TV with AV input OR VCR or DVD player with AV input attached to your TV.

• RF Adapter (not included) required if your TV does not have an AV input.

• STANDARD, CRT TV ONLY. NOT FOR USE WITH PROJECTION, LCD, HIGH-DEFINITION, OR PLASMA TV.

• You cannot play this game through a cable box or satellite hookup. Game must be

connected directly to the TV, VCR, or DVD player.

• If the game malfunctions or freezes, you can reset it by turning your Tagger off

and then on again.

Note: Do not use the PINPOINT SIGHT with

the Video Game Module.

ASSEMBLY

Get other manuals https://www.bkmanuals.com

Connecting to a TV:

1. Insert the cable’s white plug into the white audio-in jack

on the TV.

2. Insert the cable’s yellow plug into the yellow video-in jack

on the TV.

Connecting to a VCR or DVD player:

1. Make sure the VCR or DVD player is properly connected

to the TV.

2. Insert the cable’s white plug into the white audio-in

jack on the VCR or DVD player.

3. Insert the cable’s yellow plug into the yellow video-in

jack on the VCR or DVD player.

4. Turn on your TV and VCR or DVD player.

5. Set your TV, VCR or DVD player to the channel/video input

mode directed by your TV, VCR or DVD player owner’s manual.

SETUP

Insert the cable plugs into the AV inputs on your TV, VCR or DVD player.

POWER

STEREO

TIMER/

STAND BY

- CHANNEL +

- VOLUME +

TV/VIDEO

DEMO

VIDEO

VIDEO 2 INPUT

L AUDIO R

Note: these jacks are normally found on the front of

the TV near the adjustment controls, or on the back

of the TV near the antenna and cable connections

3. Turn on your TV, and set it to the channel/video input mode

directed by your TV owner’s manual.

Get other manuals https://www.bkmanuals.com

Inhaltsverzeichnis

Andere Hasbro Spielzeug Handbücher

Hasbro

Hasbro PLAYSKOOL Boohbah Get Up & Dance Jumbah Bedienungsanleitung

Hasbro

Hasbro 3116 Bedienungsanleitung

Hasbro

Hasbro G.I. Joe Cobra Ice Cutter Bedienungsanleitung

Hasbro

Hasbro Transformers Prime Energon Driller with Knock... Bedienungsanleitung

Hasbro

Hasbro UglyDolls E4521 Bedienungsanleitung

Hasbro

Hasbro Disney Start Wars The Black Series Bedienungsanleitung

Hasbro

Hasbro Transformers Bumblebee Cyberverse Adventures... Bedienungsanleitung

Hasbro

Hasbro PeepingPup Bedienungsanleitung

Hasbro

Hasbro TRANSFORMERS CYBERVERSE MEGATRON Bedienungsanleitung

Hasbro

Hasbro Beyblade Metal Driger 82656 Bedienungsanleitung

Hasbro

Hasbro My Little Pony Celebration Castle 60070 Bedienungsanleitung

Hasbro

Hasbro Transformers 80260 Bedienungsanleitung

Hasbro

Hasbro Baby Alive Bouncin' Babbles Bedienungsanleitung

Hasbro

Hasbro Fur Real Friends Daisy Plays-with-me kitty Bedienungsanleitung

Hasbro

Hasbro Deep Desert Brawl Decepticon 81058 Bedienungsanleitung

Hasbro

Hasbro FurReal Friends Butterscotch Pony 76471 Bedienungsanleitung

Hasbro

Hasbro Spiderman 3 Sandman's Sand Rider 69225/69129 Bedienungsanleitung

Hasbro

Hasbro Minecraft Ender Dragon NERF Bedienungsanleitung

Hasbro

Hasbro G.I.Joe Tiger Shark Bedienungsanleitung

Hasbro

Hasbro Disney STAR WARS THE BLACK Series Bedienungsanleitung

Hasbro

Hasbro Transformers Cybertron Dark Crumplezone... Bedienungsanleitung

Hasbro

Hasbro Cinderella Musical Castle 10119 Bedienungsanleitung

Hasbro

Hasbro Star Wars The Force Unleashed Lightsaber... Bedienungsanleitung

Hasbro

Hasbro Smokescreen Transport with Beachhead... Bedienungsanleitung

Beliebte Spielzeug Handbücher anderer Marken

marklin

marklin 37321 Bedienungsanleitung

Canon

Canon PAPER CRAFT Bedienungsanleitung

GREAT PLANES

GREAT PLANES Pitts M-12S Bedienungsanleitung

NOCH

NOCH 14261 Bedienungsanleitung

Hausler

Hausler 450 SE V2 Bedienungsanleitung

Dynaflite

Dynaflite Daydream Bedienungsanleitung

Kenner

Kenner Batman 63651 Bedienungsanleitung

LEGO

LEGO 8527 Bedienungsanleitung

Multiplex

Multiplex EasyStar II Bedienungsanleitung

iKarus

iKarus ECO 8 Bedienungsanleitung

Walkera

Walkera 38 Bedienungsanleitung

MD MXION SWD Bedienungsanleitung

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Bedienungsanleitung

marklin

marklin 39671 Bedienungsanleitung

LEGO

LEGO TECHNIC 8735 Bedienungsanleitung

Mattel

Mattel HOTWHEELS DWL04 Bedienungsanleitung

REVELL

REVELL Bristol Beaufighter TF.X Bedienungsanleitung

Ravensburger

Ravensburger 3D Puzzle La Tour Eiffel Bedienungsanleitung