Havis DS-PAN-214 Bedienungsanleitung

Installation Instructions

Havis Weatherproof Docking Station

For Panasonic CF-19 Toughbook

DS-PAN-214_OMN_10-11

www.havis.com

1-800-524-9900

Supplement to Owner’s Manual

DS-PAN-214 & DS-PAN-214-2

Havis, Inc.

75 Jacksonville Road, PO Box 2099

Warminster, PA 18974

47801 Anchor Court

Plymouth, MI 48170

www.havis.com 1-800-524-9900

www.havis.com • 1-800-524-9900

1 6

1). Taking care to remove any excess moisture which may be present, remove

Docking Connector Cover by unscrewing the two thumb screws. Use the

Tether Loop if desired to attach Docking Connector Cover to a xed object.

(Tether not included) If Tether option is not used, store Docking Connector

Cover in a safe, dry location.

2). Follow Docking and Undocking instructions in the Owner’s Manual (Pages 7-8),

making sure to apply downward pressure to the computer while latching in

order to suﬃciently compress the Gasket surrounding the Docking Connector.

3). Taking care once again to remove any excess moisture from the computer

and Docking Station, Undock the computer according to the Owner’s Manual

(Page 8) and lower the Docking Connector Cover on the Docking Station.

Hand tighten the two thumb screws.

DS-PAN-214 DS-PAN-214-2

Before Beginning Docking & Undocking

(Original Instructions)

• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.

• DO NOT MATE COMPUTER TO DOCKING STATION UNLESS COMPUTER’S DOCKING

CONNECTOR ACCESS DOOR IS FULLY OPEN OR DAMAGE MAY RESULT.

• ALWAYS USE DOCKING CONNECTOR COVER WHEN DOCKING STATION IS NOT IN USE.

• TO MAXIMIZE THE LIFE OF YOUR PRODUCT, IT MAY BE NECESSARY TO ROUTINELY

REMOVE EXCESS MOISTURE OR CONTAMINANTS FROM THE DOCKING STATION

EXTERNAL SURFACES, ESPECIALLY THE LOCK AND REGIONS SURROUNDING THE

DOCKING CONNECTOR AND CABLE CONNECTORS.

This document is a supplement to the supplied Owner’s Manual,

and applies only to installation and use of the IP65 compliant

DS-PAN-214 & DS-PAN-214-2 Docking Stations for the Panasonic

CF-19 laptop computer.

For questions regarding the set-up of your DS-PAN-214 or

DS-PAN-214-2 Docking Station, please contact Havis at

1-800-524-9900 or visit www.havis.com for additional

product support and information.

This Supplement applies to the following Part Numbers:

Tether Loop

Thumb Screws

www.havis.com • 1-800-524-9900

5 2

5). Lower Cable Cover into place on Docking Station, making sure all six cable

exits have a Grommet with cable inserted, or a Grommet with Grommet Plug

inserted. Fasten #8-32 Pan Head Phillips Screws in 6 places as shown.

Torque all six #8-32 Pan Head Phillips Screws to 20 ± 10% in-lbs.

6). Insert Zip Ties into strain relief holes on the Cable Cover in order to secure

exiting cables. Cut oﬀ excess from connected Zip Ties. Ensure that Zip Tie

is routed beneath cable for adequate strain relief.

If you are routing Antenna cable(s) (Part # DS-PAN-214-2), use Push Pin Zip Ties

supplied with the Docking Station Hardware Kit to secure the cable(s) to the Strain

Relief Holes at the back of the Docking Station. Then route the cables to the cable

bundle and secure as specied in the Owner’s Manual (Page 6, Step 5).

Parts Included

Installation & Cable Management (continued)

Port Replication

Lock

Latch Handle

Docking Connector

Gasket

Front Hooks

Docking Station

Additional Parts

1. Mounting Bracket (1)

2. Cable Cover (1)

3. Docking Connector Cover (1)

with Thumb Screws

4. #8-32 Pan Head Phillips Screws (7)

5. Grommets (7)

6. Grommet Plugs (7)

7. Zip Ties (7)

8. Foam Tape

9. DS-PAN-210 Series Owner’s

Manual & Hardware Kit

(not shown)

Includes: Zip Ties (4), Keys (2),

1/4”-20 Screws (3), M5 Screws (4)

Antenna Strain

Relief Holes (4)

Strain Relief Hole

Forward Facing Connectivity

Rearward Facing Connectivity

(Part # DS-PAN-214-2 only)

NOTE: A maximum of six (6)

connections can be made on

DS-PAN-214 & DS-PAN-214-2

Docking Stations

Ethernet

(RJ45)

Serial

(x2)

VGA

Power

Input USB 2.0

(x3)

Antenna B Antenna A

Speaker / Headphone

Microphone

www.havis.com • 1-800-524-9900

3 4

1). Place Docking Station top side down on a stable surface and connect

all necessary cables needed for operation.

NOTE: Do not exceed a cable diameter of 0.315” (8.00 mm)

2). With all cables connected, determine the optimal routing of cables to

the Cable Cover exits, taking care to avoid cable obstructions. For all

cables with a diameter less than 0.25” (6.0 mm), cut small strips of

supplied Foam Tape to wrap around cables to enlarge the diameter to

the optimal 0.25”. Ensure the Foam Tape is positioned at the determined

exit point from Cable Cover.

3). For each exiting cable, use a sharp knive or scissors to cut through the center

of a rubber Grommet in order to insert the cable into Grommet hole. (Fig. A)

DO NOT CUT GROMMETS FOR CABLE COVER EXITS WITHOUT EXITING CABLES.

Instead, add a Grommet Plug and insert Grommet into the Cable Cover

in the orientation shown. (Fig. B)

4). Secure the cut Grommet around cable or Foam Tape in the position identied

in Step 2. Insert Grommets with cables intact into the appropriate cable

exits in the Cable Cover, taking care to not pinch cables. Use a Grommet

with Grommet Plug for all exits not occupied with a Grommet and cable.

The following instructions are meant to take the place of the ‘Installation’

and ‘Cable Management’ sections of the Owner’s Manual (Pages 4-6).

Please read all included instructions thoroughly before beginning installation.

NOTE: Only six (6) total cables can

be routed through the Cable Cover.

Foam Tape

Cable

0.25”

Cross section view of Cable

wrapped in Foam Tape

Installation & Cable Management (continued)

Installation & Cable Management

Fig. A:

Cut Grommet to accept cable

Fig. B:

Plug un-cut Grommet

Foam Tape

Cable

CAUTION

Use care operating scissors or

knives while cutting objects

CAUTION

Use care operating scissors or

knives while cutting objects

www.havis.com • 1-800-524-9900

3 4

1). Place Docking Station top side down on a stable surface and connect

all necessary cables needed for operation.

NOTE: Do not exceed a cable diameter of 0.315” (8.00 mm)

2). With all cables connected, determine the optimal routing of cables to

the Cable Cover exits, taking care to avoid cable obstructions. For all

cables with a diameter less than 0.25” (6.0 mm), cut small strips of

supplied Foam Tape to wrap around cables to enlarge the diameter to

the optimal 0.25”. Ensure the Foam Tape is positioned at the determined

exit point from Cable Cover.

3). For each exiting cable, use a sharp knive or scissors to cut through the center

of a rubber Grommet in order to insert the cable into Grommet hole. (Fig. A)

DO NOT CUT GROMMETS FOR CABLE COVER EXITS WITHOUT EXITING CABLES.

Instead, add a Grommet Plug and insert Grommet into the Cable Cover

in the orientation shown. (Fig. B)

4). Secure the cut Grommet around cable or Foam Tape in the position identied

in Step 2. Insert Grommets with cables intact into the appropriate cable

exits in the Cable Cover, taking care to not pinch cables. Use a Grommet

with Grommet Plug for all exits not occupied with a Grommet and cable.

The following instructions are meant to take the place of the ‘Installation’

and ‘Cable Management’ sections of the Owner’s Manual (Pages 4-6).

Please read all included instructions thoroughly before beginning installation.

NOTE: Only six (6) total cables can

be routed through the Cable Cover.

Foam Tape

Cable

0.25”

Cross section view of Cable

wrapped in Foam Tape

Installation & Cable Management (continued)

Installation & Cable Management

Fig. A:

Cut Grommet to accept cable

Fig. B:

Plug un-cut Grommet

Foam Tape

Cable

CAUTION

Use care operating scissors or

knives while cutting objects

CAUTION

Use care operating scissors or

knives while cutting objects

www.havis.com • 1-800-524-9900

5 2

5). Lower Cable Cover into place on Docking Station, making sure all six cable

exits have a Grommet with cable inserted, or a Grommet with Grommet Plug

inserted. Fasten #8-32 Pan Head Phillips Screws in 6 places as shown.

Torque all six #8-32 Pan Head Phillips Screws to 20 ± 10% in-lbs.

6). Insert Zip Ties into strain relief holes on the Cable Cover in order to secure

exiting cables. Cut oﬀ excess from connected Zip Ties. Ensure that Zip Tie

is routed beneath cable for adequate strain relief.

If you are routing Antenna cable(s) (Part # DS-PAN-214-2), use Push Pin Zip Ties

supplied with the Docking Station Hardware Kit to secure the cable(s) to the Strain

Relief Holes at the back of the Docking Station. Then route the cables to the cable

bundle and secure as specied in the Owner’s Manual (Page 6, Step 5).

Parts Included

Installation & Cable Management (continued)

Port Replication

Lock

Latch Handle

Docking Connector

Gasket

Front Hooks

Docking Station

Additional Parts

1. Mounting Bracket (1)

2. Cable Cover (1)

3. Docking Connector Cover (1)

with Thumb Screws

4. #8-32 Pan Head Phillips Screws (7)

5. Grommets (7)

6. Grommet Plugs (7)

7. Zip Ties (7)

8. Foam Tape

9. DS-PAN-210 Series Owner’s

Manual & Hardware Kit

(not shown)

Includes: Zip Ties (4), Keys (2),

1/4”-20 Screws (3), M5 Screws (4)

Antenna Strain

Relief Holes (4)

Strain Relief Hole

Forward Facing Connectivity

Rearward Facing Connectivity

(Part # DS-PAN-214-2 only)

NOTE: A maximum of six (6)

connections can be made on

DS-PAN-214 & DS-PAN-214-2

Docking Stations

Ethernet

(RJ45)

Serial

(x2)

VGA

Power

Input USB 2.0

(x3)

Antenna B Antenna A

Speaker / Headphone

Microphone

www.havis.com • 1-800-524-9900

1 6

1). Taking care to remove any excess moisture which may be present, remove

Docking Connector Cover by unscrewing the two thumb screws. Use the

Tether Loop if desired to attach Docking Connector Cover to a xed object.

(Tether not included) If Tether option is not used, store Docking Connector

Cover in a safe, dry location.

2). Follow Docking and Undocking instructions in the Owner’s Manual (Pages 7-8),

making sure to apply downward pressure to the computer while latching in

order to suﬃciently compress the Gasket surrounding the Docking Connector.

3). Taking care once again to remove any excess moisture from the computer

and Docking Station, Undock the computer according to the Owner’s Manual

(Page 8) and lower the Docking Connector Cover on the Docking Station.

Hand tighten the two thumb screws.

DS-PAN-214 DS-PAN-214-2

Before Beginning Docking & Undocking

(Original Instructions)

• READ ALL INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION.

• DO NOT MATE COMPUTER TO DOCKING STATION UNLESS COMPUTER’S DOCKING

CONNECTOR ACCESS DOOR IS FULLY OPEN OR DAMAGE MAY RESULT.

• ALWAYS USE DOCKING CONNECTOR COVER WHEN DOCKING STATION IS NOT IN USE.

• TO MAXIMIZE THE LIFE OF YOUR PRODUCT, IT MAY BE NECESSARY TO ROUTINELY

REMOVE EXCESS MOISTURE OR CONTAMINANTS FROM THE DOCKING STATION

EXTERNAL SURFACES, ESPECIALLY THE LOCK AND REGIONS SURROUNDING THE

DOCKING CONNECTOR AND CABLE CONNECTORS.

This document is a supplement to the supplied Owner’s Manual,

and applies only to installation and use of the IP65 compliant

DS-PAN-214 & DS-PAN-214-2 Docking Stations for the Panasonic

CF-19 laptop computer.

For questions regarding the set-up of your DS-PAN-214 or

DS-PAN-214-2 Docking Station, please contact Havis at

1-800-524-9900 or visit www.havis.com for additional

product support and information.

This Supplement applies to the following Part Numbers:

Tether Loop

Thumb Screws

Installation Instructions

Havis Weatherproof Docking Station

For Panasonic CF-19 Toughbook

DS-PAN-214_OMN_10-11

www.havis.com

1-800-524-9900

Supplement to Owner’s Manual

DS-PAN-214 & DS-PAN-214-2

Havis, Inc.

75 Jacksonville Road, PO Box 2099

Warminster, PA 18974

47801 Anchor Court

Plymouth, MI 48170

www.havis.com 1-800-524-9900

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Havis Dockingstation Handbücher

Havis

Havis DS-PAN-1110 Series Bedienungsanleitung

Havis

Havis DS-PAN-421 Bedienungsanleitung

Havis

Havis DS-ZEB-100 Series Bedienungsanleitung

Havis

Havis DS-DELL-410 Series Bedienungsanleitung

Havis

Havis DS-GTC-900 Series Bedienungsanleitung

Havis

Havis DS-PAN-1500 Series Bedienungsanleitung

Havis

Havis DS-PAN-110 Series Bedienungsanleitung

Havis

Havis DS-GTC-502 Bedienungsanleitung

Havis

Havis DS-PAN-701 Bedienungsanleitung

Havis

Havis DS-APP-100 Series Bedienungsanleitung

Havis

Havis DS-PAN-1014 Bedienungsanleitung

Havis

Havis DS-PAN-100 Series Montageanleitung

Havis

Havis DS-GTC-701 Bedienungsanleitung

Havis

Havis DS-GTC-7X0 Series Bedienungsanleitung

Havis

Havis DS-DELL-904 Bedienungsanleitung

Havis

Havis TC-106 Bedienungsanleitung

Havis

Havis DS-GTC-511 Bedienungsanleitung

Havis

Havis Ledco Installations- und Betriebshandbuch

Havis

Havis DS-DELL-101 Bedienungsanleitung

Havis

Havis DS-PAN-724 Bedienungsanleitung

Havis

Havis DS-PAN-1400 Series Bedienungsanleitung

Havis

Havis DS-PAN-900 Series Bedienungsanleitung

Havis

Havis DS-PAN-801 Bedienungsanleitung

Havis

Havis DS-DELL-420 Series Bedienungsanleitung

Beliebte Dockingstation Handbücher anderer Marken

Sony

Sony Dream Machine XDR-DS12iP Bedienungsanleitung

Acer

Acer USB Type-C Dock II Bedienungsanleitung

ATEN

ATEN UC-2000 Bedienungsanleitung

Xcellon

Xcellon HDD-202 Bedienungsanleitung

Dok

Dok CR09 Bedienungsanleitung

Philips

Philips BTM630/12 Bedienungsanleitung

IOGear

IOGear Travel Pro GUD3C09 Bedienungsanleitung

RKI

RKI SDM-E2 Bedienungsanleitung

iHome

iHome iP15 Bedienungsanleitung

VITURE ONE

VITURE ONE MOBILE DOCK Bedienungsanleitung

Lindy

Lindy 42984 Bedienungsanleitung

CipherLab

CipherLab 8001 Bedienungsanleitung

Pyle

Pyle PIPDSP2 Bedienungsanleitung

Avol

Avol AS2350 Bedienungsanleitung

Datalogic

Datalogic JoyaTouch Bedienungsanleitung

Philips

Philips DC190/79 Bedienungsanleitung

Targus

Targus DOCK315EUZ Bedienungsanleitung

Akasa

Akasa DuoDockX3 AK-DK08U3-BK Bedienungsanleitung