Hayward TriStar VS 900 Omni Bedienungsanleitung

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Hayward Pool Products

620 Division Street, Elizabeth NJ 07207

Phone (908)-355-7995

www.hayward.com

Operation Manual

092693 RevC

Contents

Introduction............................................2

Favorites................................................17

Themes.................................................22

Cong...................................................24

Upgrade................................................27

Simple Mode........................................30

WebEnabledControl..............................33

Warranty................................................34

VS Omni

Pool Automation Control

HL32950VSP HL32900VSP

HL2350020VSP HL2670020VSP

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

IMPORTANT SAFETY INSTRUCTIONS

When using this electrical equipment, basic safety precautions should always be followed, includ-

ing the following:

• READ AND FOLLOW ALL INSTRUCTIONS

• WARNING: Disconnect all AC power during installation.

• WARNING: Water in excess of 100 degrees Fahrenheit may be hazardous to your health.

• WARNING: To reduce the risk of injury, do not permit children to use this product unless they

are closely supervised at all times.

• WARNING: Do not use the VS Omni to control ﬁre pits or related equipment.

• A green colored terminal marked “Grounding” is located inside the wiring compartment. To

reduce the risk of electric shock, this terminal must be connected to the grounding means

provided in the electric supply service panel with a continuous copper wire equivalent in size

to the circuit conductors supplying the equipment.

• One bonding lug for US models (two for Canadian models) is provided on the external

surface. To reduce the risk of electric shock, connect the local common bonding grid in the

area of the swimming pool, spa, or hot tub to these terminals with an insulated or bare copper

conductor not smaller than 8 AWG US / 6 AWG Canada.

• All ﬁeld installed metal components such as rails, ladders, drains, or other similar hardware

within 3 meters of the pool, spa or hot tub shall be bonded to the equipment grounding bus

with copper conductors not smaller than 8 AWG US / 6 AWG Canada.

SAVE THESE INSTRUCTIONS

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Introduction

This manual assumes that the VS Omni has been installed and conﬁgured according to the Installa-

tion Manual. The VS Omni can now be programmed with user desired settings such as schedules,

themes, and favorites. This manual will also explain how to manually turn pool equipment on/off,

program settings for speciﬁc equipment, view pool equipment status and conditions, and more.

Now that the initial conﬁguration has been completed, the VS Omni will automatically go to the

Home Screen or Idle Screen. All settings and operation functions can be accessed from the Home

Screen. Note that if the VS Omni Control Pad is not touched for more than two minutes, the Idle

Screen will be displayed.

Using the Control Pad

The VS Omni uses the Control Pad touchscreen as the main interface with the device. Once

conﬁgured, the VS Omni can be controlled remotely by internet enabled devices such as comput-

ers, tablets, and phones. The Control Pad must be used to access the Conﬁguration Wizard. The

Conﬁguration Wizard is used for initial conﬁguration (completed during the installation process) and

for any changes to existing conﬁguration.

Idle Screen

The Control Pad will display the idle screen after two minutes of user inactivity. When the ﬁlter

pump is on, the Idle Screen will display the current temperature of the pool on the left side of the

screen. On the right side of the screen, the time will be displayed and the air temperature will

toggle with the date as well as other information.

ºF

82 9:13 PM

FRIDAY

jul 13

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Home Screen

When the Idle Screen is touched, the VS Omni will display the Home Screen. This screen will give

the user access to all functions, settings, and conﬁguration options.

Power Button

The power button is displayed at all times when the VS Omni is not idle. When touched, it offers

the following 4 functions:

Shut Down - When Shut Down is selected, the VS Omni will turn off all pool equipment and report

when it is safe to remove power. When this message is displayed, you can either power off the unit

or restart the VS Omni by touching the large power button displayed on the left side of the screen.

Service Mode - Service Mode will turn off all pool equipment and disable all networked devices.

Service Mode is useful to prevent scheduled operation and disable remote operation while servic-

ing the pool. After selecting Service Mode, there are two options:

Service Mode (Standard): The VS Omni will remain in Service Mode until you manually exit.

To exit Service Mode, touch the power button and select the Service Mode button again.

Service Mode Timed: Before entering Service Mode, you will select a Service Mode timeout.

This is the amount of time that the VS Omni will stay in Service Mode before automatically

exiting. The timeout can be set between 1-96 hours. There is no need to exit Service Mode

manually.

daylight

features lights

air

71º F

alarm

daylight

features lights

ºF

air

71º F

alarm

shut down

service

mode

simple

mode

features

o

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Features Off - Features Off offers a quick way to turn off all equipment (except the ﬁlter pump and

ColorLogic lights if running because of a schedule) with a single touch of a button.

Simple Mode - Simple Mode is a customizable screen that can be set up for quick access to your

Favorites (page 17). You can set up only the Favorites that you want shown while in Simple Mode.

Because it’s customizable, Simple Mode can provide a convenient way to access the most common

functions for owners as well as a handy solution to limit access to other users. For information on

how to create and delete Simple Mode functions, refer to the “Favorites” section in this manual.

The MSP ID number (page 27) is needed when entering and exiting Simple Mode.

Selecting a Body of Water - Left Side of Home Screen

The left side of the Home Screen allows you to select and control a Body of Water. If more than one

Body of Water is used (typically a pool and a spa), pressing the left and right arrows shown below

toggle between the Bodies of Water. If just a pool is conﬁgured, there will be no arrows shown.

Controlling a Body of Water

When the desired Body of Water is displayed, touch the left side of the screen to advance to the Body

of Water Features Screens. The items shown on the Features Screen relate to that Body of Water

ONLY. To control a different Body of Water, select the desired Body of Water at the Home Screen ﬁrst,

then go to the Features Screens.

daylight

favorites

alarm

lights

ºF

air

71º F

Use arrow buttons on left side of screen to change Body of Water.

daylight

favorites

alarm

lights

ºF

air

71º F

SPA

102

daylight

favorites

alarm

lights

ºF

air

71º F

SPA

102

uclights chlorinator

alarm light hung

1 / 2

vsp pH

heater cleaner

POOL

features

When the desired Body of Water is displayed, touch left side of screen

to enter Control Screens.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Features (left side of the Home Screen)

After selecting the desired Body of Water (if applicable), touch the left side of the screen to advance

to the Features Screen. The various buttons shown in the Features Screen are related to initial

conﬁguration. For example, if you conﬁgured a heat pump to heat the pool, then the heater set-

tings for the heat pump will be displayed.

Favorites - Right Side of Home Screen

The right side of the Home Screen is Favorites. These buttons offer universal control for all Bodies

of Water and Backyard equipment. Up to four Favorite buttons will be shown on the Home screen.

To access more Favorites, touch the arrows on the left or right of the Favorite buttons.

Note that some default buttons will appear on the Favorites Screen. These buttons are related

to your initial conﬁguration settings and are automatically created. In addition, custom “Favorite”

buttons can also be added. The VS Omni supports up to 50 Favorites for quick, easy access to

commonly used functions.

Navigation

The VS Omni has been designed to be intuitive, allowing most users the ability to navigate with

little instruction. Following is a list of commonly used buttons. As you navigate through the various

screens, these buttons will likely be displayed. Some sections of this manual may refer to buttons

that are speciﬁc to certain types of pool equipment. You’ll ﬁnd more information about those but-

tons under their corresponding section. If your installation does not include that particular equip-

ment, those sections can be skipped.

daylight

features lights

ºF

air

71º F

alarm

uclights

vsp

heater cleaner

POOL

features

schedule

daylight

features lights

ºF

air

71º F

alarm favorites

heating themes

ºF

air

71º F

cong

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Save - Touch this button to save your selection.

Cancel - Touch this button to cancel your selection.

Advance - Touch this button to advance to the next screen.

Back - Touch this button to return to the previous screen.

Add - Touch this button to add an item.

Delete - Touch this button to delete a highlighted item.

Turn On or Enable - This button will either manually turn on pool equipment or enable a

function.

Turn Off or Disable - This button will either manually turn off pool equipment or disable

a function.

Schedule - Touch this button to schedule a function.

Countdown Timer - Touch this button to set a countdown timer.

Back - Touch this button to return to a previous screen.

Features and Control Screens

As previously stated, the Features Screen allows you to control functions and equipment. The

contents of the Features Screen is a result of how the VS Omni was conﬁgured using the Conﬁgu-

ration Wizard. If equipment is missing or does not belong in the Features Screen, you may have to

go back to the Conﬁguration Wizard and correct the conﬁguration of that equipment.

An example of a Features Screen is shown below. In this example, we are looking at the Pool

(shown in the lower left of the screen) conﬁgured with a pump, a heater, a cleaner, and UCL lights.

Depending on the equipment in your system, your screens will likely be different. The purpose of

this section is to explain how Features and Control Screens work as well as show some common

equipment examples which will help familiarize you with the interface. Even though some of your

equipment may be different, you should see similarities in the following examples that will help you

create and change settings for all the equipment in your Features Screens.

OFF

uclights

vsp

heater cleaner

POOL

features

schedule

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Note that the following examples will be shown for the Pool only. All of the equipment shown in

the Features Screens will have been initially conﬁgured in the Conﬁguration Wizard to operate with

a Pool body of water. You may have conﬁgured the VS Omni to share equipment with the Spa in

which case the equipment will be shown in the Features Screen for both the Pool and Spa.

Control Screens

After an item has been selected in the Features Screen, you’ll be brought to a control screen.

Control Screens are used to make changes to the pool’s equipment settings. To change a setting,

you’ll ﬁrst touch the left side of the Home Screen to enter the Features Screen, then select the

equipment you’d like to set.

Filter Pump

In the example below, a variable speed pump which was named “vsp” has been conﬁgured to be

used with the Pool in the Conﬁguration Wizard. Touching the “vsp” button in the Features Screen

will bring you to a pump Control Screen which will let you manually turn on/off the pump, view

the status, set a schedule, set a speed, start a countdown timer, or view the pump’s diagnostics.

Single speed and two speed pumps will have a similar Control Screen.

POOL

vsp pump

MED HIGH CUSTOMLOW

Change Speed - Manually

select the desired speed. This

will not be shown for single

speed pumps. Low, Med, and

High are ﬁxed speeds. The

Custom button will bring you

to a screen that allows you to

select a speed based on per-

centage or RPM (determined

during conﬁguration).

Turn On / Turn Off - Slide

this switch manually to turn

on/off the pump. This will

override any schedules or timer

settings.

Status of Equipment - This is an indicator

only. When lit up and in motion (shown be-

low), the equipment is active. When grayed

out and stationary, the equipment is off.

Set Schedule - Touch

this button to add/delete a

schedule for the ﬁlter pump

or to enable/disable an

existing schedule.

Countdown Timer - Touch

this button to set a count-

down timer for the ﬁlter

pump.

Diagnostics - Touch this

button to view the ﬁlter

pump’s diagnostics. This

option only appears for vari-

able speed pumps.

uclights

vsp

heater cleaner

POOL

features

schedule

POOL

vsp pump

MED HIGH CUSTOMLOW

Pool Features Screen Pump Control Screen

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Add a Schedule

If the “Set Schedule” button is touched, you’ll be brought to the pump schedule screen below.

Here you can add, delete, edit, enable, and disable schedules. Because there have been no sched-

ules set up, the screen is blank. Touch the Add button (+) to add a schedule for the pool pump.

Set Schedule Time

Refer to the screen below to set the start and end times. When ﬁnished, touch “repeat”.

Set Schedule Frequency

Refer to the screen below to select how often you’d like the schedule to run. If “custom” is

selected, you’ll be asked which day(s) of the week you would like the pump to run. Touch “speed”

when ﬁnished.

POOL

vsp pump

Please press + button to add schedule items.

ON/OFF

end 7:00 pm

POOL

vsp pump

start 10:00 am

start / end

repeat

speed

end 7:00 pm

POOL

vsp pump

start 10:00 am

start / end

repeat

speed

Set Start Time - Select this

button to edit the start time.

The pump will start at the time

shown.

Edit Time - Select the Hours,

Minutes, or AM/PM ﬁelds to

change the desired time.

Set End Time - Select this button to edit the

end time. The pump cycle will end at the

time shown.

Set Schedule Frequency -

Select how often you’d like the

schedule to run (weekdays,

weekends, all week, custom).

Set Pump Speed - Select this

button to change the pump

speed for the schedule. This

option only appears for variable

speed and two speed pumps.

POOL

vsp pump

start / end

repeat

speed

weekdays all weekweekends

custom

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Set Pump Speed

Refer to the screen below to select the pump speed during the schedule. If custom is selected,

you’ll be asked to set the % pump speed or RPM depending on the setting. When ﬁnished, touch

the Save button to save the schedule. NOTE: the speed setting only appears if the pump is a vari-

able speed or a two speed pump.

NOTE: if you intend to run the pump at different speeds throughout the day, create additional

schedules. You can start a new schedule on the same minute that the previous one ends. If

schedules overlap, the newest schedule’s start time will take priority by ending the previous sched-

ule early. You can create up to 100 total schedules on the system.

Edit a Schedule

To edit a schedule, touch the schedule as shown below. You’ll be brought back to the screen which

will allow you to set times, speed and frequency.

POOL

vsp pump

start / end

repeat

speed

low highmed

custom

POOL

vsp pump

01 10:00 am / 7:00 pm med all week

POOL

vsp pump

01 10:00 am / 7:00 pm med all week ON

end 7:00 pm

POOL

vsp pump

start 10:00 am

start / end

repeat

speed

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward SwimPure Plus Technisches Datenblatt

Hayward

Hayward Paramount MDX-R3 Programmierhandbuch

Hayward

Hayward Sense and Dispense Bedienungsanleitung

Hayward

Hayward WFL100 ColorLogic Bedienungsanleitung

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Pool pH Bedienungsanleitung

Hayward

Hayward AquaRite+ AU Master Handbuch

Hayward

Hayward HL32950VVSP Bedienungsanleitung

Hayward

Hayward WFBRNDBRS Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Aqua Rite® Pro Bedienungsanleitung

Hayward

Hayward Goldline Controls Aqua Logic AQL-P-4 Bedienungsanleitung

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Hayward

Hayward OmniHub Bedienungsanleitung

Hayward

Hayward AQL-CHEM Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward Control Station Bedienungsanleitung

Hayward

Hayward AQL-CHEM4-ACID Bedienungsanleitung

Hayward

Hayward SP1091LX Bedienungsanleitung

Hayward

Hayward S311SX Bedienungsanleitung

Hayward

Hayward Jiffy Niche Bedienungsanleitung

Hayward

Hayward ProLogic Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung