Hayward AquaRite+ AU Master Handbuch

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

Hayward Pool Products (Australia) Pty Ltd.

Melbourne-Sydney-Brisbane-Perth

Email: [email protected] | Website: www.hayward-pool.com.au

PO Box 4384 | Dandenong South VIC 3164

ABN 66 083 413 414

Sales Contact Ph: 1300POOLS1 Fax: 1300POOLS2

PLEASE KEEP THIS MANUAL FOR FUTURE REFERENCE

AquaRite™+ AU Master and Slave Installation and Setup

To prevent potential injury and to avoid unnecessary service

calls, read this manual carefully and completely.

Addional Resource Manual

For Pools over 150,000 L in Cool Climates and 110,000 L for Tropical Climates

30-LITINSD012RB

Master Slave

Page 2

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

WARNING: Electrical hazard.

Failure to comply with these instructions can result in

serious injuries or death.

THE EQUIPMENT IS INTENDED TO BE USED ONLY ON

PERMANENTLY CONSTRUCTED POOLS AND SPAS

WARNING – Disconnect/isolate the equipment from the electricity supply before any

installation/service/repair.

WARNING – All electrical wiring must be performed by a qualified and licensed electrical

contractor in accordance with all Local/State/Federal Government electrical regulations and

the latest edition of the AS/NZS 3000 Wiring Rules.

WARNING – Ensure that the device is plugged into a power outlet that is protected against

short-circuits. The device must also be powered via an isolating transformer or through a

residual current device (RCD) with a fixed residual operating current not exceeding 30 mA.

WARNING – Check that the supply voltage required by the product corresponds to the

voltage of the distribution network.

WARNING – To reduce the risk of electric shock, do not use an extension cord to connect the

device to the mains. Use a suitably rated GPO as per the standard AS/NZS 3000.

WARNING – Chemicals can cause internal and external burns. To avoid death, serious injury

and/or damage to equipment, wear personal protective equipment (gloves, goggles, mask,

etc.) when servicing or maintaining this device. This device must be installed in an adequately

ventilated place when equipped with the chemical feed options.

WARNING – Carefully read the instructions that appear in this manual and on the device.

Failure to comply with the instructions can cause injuries. This document must be given to the

pool owner who should keep it in a safe place.

WARNING – The appliance can be used by children aged from 8 years and above and

persons with reduced physical, sensory or mental capabilities, or lack of experience and

knowledge, if they have been given supervision or instruction concerning use of the appliance

in a safe way and understand the hazards involved.

WARNING – Use only genuine Hayward replacement parts.

WARNING –If the power supply cord is damaged the device must not be used. The power

supply cord must be replaced by the manufacturer or similarly qualified persons to avoid any

danger.

Page 3

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

INTRODUCTION

The use of a Master and Slave AquaRite+ AU setup allows the system to better meet the chlorine demand requirements

of the pool. It is ideal in pools that exceed 150,000 litres in cool climates and 110,000 litres in tropical climates. By

controlling one AquaRite+ AU unit with another, the first unit acts as the Master unit and is installed with the pH and ORP

Upgrade Kits, while the second unit acts as the Slave unit and will produce chlorine when instructed to by the Master unit.

In instances where the Master unit cannot keep up with the chlorine demand of the pool, it will signal for the Slave

chlorinatior to be turned on once the ORP level falls to 2% below the ORP/Redox set point. The Slave unit will then begin

to produce chlorine until the ORP/Redox set point has been reached.

NOTE: Before installing this product as part of a salt water puriﬁcation system in a pool or spa using natural stone for coping or for immediately

adjacent patios/decking, a qualiﬁed stone installation specialist should be consulted regarding the appropriate type, installation, sealant (if any) and

maintenance of stone used around a saline pool with an electronic chlorine generator in your particular location and circumstances.

NOTE: The use of dry acid (sodium bisulfate) to adjust pool pH is discouraged especially in arid regions where pool water is subject to excessive

evaporation and is not commonly diluted with fresh water. Dry acid can cause a buildup of by-products that can damage your chlorinator cell.

COMPONENTS

Master Unit Slave Unit

Page 4

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

INSTALLATION

Master Unit

The Master unit is to be installed with the pH and ORP Upgrade Kits.

The Slave unit is to be installed next to the Master unit.

When installing a Master and Slave set up, both units must be installed on the same body of water.

They can have separate filtration systems or share a common filter with a singular filtration pump.

Each unit must have its own Flow Switch installed as per the diagrams on pages 5 and 7.

pH Probe

ORP Probe

Master Unit

Master Unit Slave Unit

Page 5

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

SHARED FILTER INSTALLATION (HORIZONTAL)

SHARED FILTER INSTALLATION (VERTICAL)

Pool

Spa

Master Cell

Slave Cell

Master

Flow Switch

Slave

Flow Switch

From the Filter

and Heater

Chemical

Injection Tee

From the Filter

and Heater

Master

Flow Switch

Master Cell

Slave

Flow Switch

Slave Cell

Spa

Pool

Chemical

Injection Tee

IMPORTANT: There must be at least 30 cm of straight pipe run before (upstream) the Flow Switch. If mounted

before the Flow Switch, the T-Cell can count as the 30 cm of straight pipe.

Page 6

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

Removing the Dead Front Panel

To access the internal circuity of the AquaRite+ AU, the Dead Front Panel needs to be carefully removed. Follow the

instructions below to avoid damaging the device and/or its casing.

Caution - Risk of Electric Shock.

Ensure that the unit has been disconnected from all power supplies before removing the Display and Dead

Front Panel. Only a suitably qualified person should remove the Dead Front Panel in accordance with Local/

State/Federal Government regulations and the latest edition of the AS/NZS 3000 Wiring Rules.

Lift Out Interactive Display Module:

Remove display module from its compartment. Use the grooves on either side to pry it out by hand. Take care to

not use excessive force as the module is still wired to the PCB at this stage.

Detach Interactive Display Module:

Turn over the display module and remove the wired plug from the port on the back of the unit. Store the Display

Module where it will not get damaged until it is re-installed.

Unscrew Dead Front Panel:

Remove the six (6) screws fastening the panel to the unit. Once all loose, lift the panel off the unit to access the

PCB.

Lift Lift

Display Module

Pull

Unscrew Unscrew

PCB

Page 7

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

Electrical Installaon and Wiring

Wiring Schematic Only

7 8

Flow Switch

12+

Master Unit

Slave Unit

1 2 3 4 67 108 9

FL1 FL1

12+

Master Unit Slave Unit

NOTE - Ensure that only 0.5 mm² to 0.75 mm² double insulated cable is used to bridge between the Master

and Slave units. The Slave unit flow switch cable is to be connected/joined to the bridging cable and

terminals inside the Slave Control unit.

The above diagram is a schematic only, and the flow switch wire is not to be pulled apart into to seperate

single insulated conductors further than what is required to make the joins/connections inside the Slave

unit housing.

Page 8

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

Cable Gland Installaon

In order to ensure watertight wire connections to the PCB through the AquaRite+ AU enclosure, wire cables are to be

secured with the black cable glands supplied. The two (2) cable glands supplied with the chlorinator are for the Cell Flow

Switch and any Light connections or Master/Slave requirements.

Tighten the gland with a spanner

whilst still holding the nut to secure

the gland in place.

Pull the cord through the gland

until the intended input point can be

reached. Secure and seal the cord in

place by fastening the domed cap with

a spanner until firm.

Insert the cable into the domed end of

the gland and pull it through.

Hold the nut against the hole on the

inside of the mounting frame. Push

the cable and gland into the hole

whilst simultaneously rotating to

screw the nut on to the thread.

Cable

Nut

Mounting

Frame

Gland

Tighten

Note: Use the gland location holes in the bottom of the unit before the sides to ensure all cables are pointing downward.

The AquaRite+ AU is to be connected to a GPO with a permanent power supply only.

CAUTION - This circuit must be protected by a residual current device (RCD) with a fixed residual

_________operating current not exceeding 30 mA.

Power Supply

Page 9

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

SPA

Pol 1

Low

22gr/h

electrolysis

measures

man

off

man

off

12:30 25º

13 4

7.4

700

Sal

g/l

15/01/16

3.2 25°C

7.5

FL1

650

3.2

25°C

15/01/16

man

aut

smt

7.5

ON/OFF

AL3

Pol 1

Flow

LOW

---

Pol 2

SPA

650

FL1

7.0

man aut

Pol 1

SPA

Pol 1 Low

22gr/h

electrolysis

measures

man

off

man

off

12:30 25º

13 4

Sal

g/l

15/01/16

3.2 25°C

3.2

25°C

15/01/16

man

aut

smt

Pol 1

Flow

LOW

---

Pol 2

SPA

man aut

Time

Chlorine production rate in gr/h

Displays manual

salt level measurement

Filtration relay state

Manual

Automatic

Smart

Communication

Red = Communication fault

Current water temperature at T-Cell

Polarity 1 Polarity 2

Production automatically reduced

to % selected (20% by default)

Wait time

Insufcient salt / cell scaled up or the

water temperature is very low (<15°C)

Filtration stopped or insufcient ow

Lighting relay state

Manual Automatic

State of auxiliary relays

(On/Off)

Date of the last salinity measurement

Salt concentration

Water temperature (when measurement taken)

Enter Main Menu/

Select & Save

BUTTONS KEY

Go Back

Navigate

Up & Down

Through Lists

Make Adjustments/

Scroll Through

Opons

Current water temperature at T-Cell

Production automatically reduced

to % selected (20% by default)

Polarity 1 Polarity 2

Wait time

Insufcient salt / cell scaled up or the

water temperature is very low (<15°C)

Filtration stopped or insufcient ow

Lighting relay state

Date of the last salinity measurement

Manual Automatic

Salt concentration

Water temperature (when measurement taken)

Time

State of auxiliary relays

(On/Off)

Chlorine production rate in gr/h

Displays manual

salt level measurement

Filtration relay state

Manual

Automatic

Smart

Communication

Red = Communication fault

pH set point

Peristaltic pump operation

Max. injection time reached

Insufcient ow

ORP/Redox set point

If the Master unit does not want the Slave unit to produce chlorine, the slave unit will display “FLOW” alert on the

display until it is called into action at which point it will display Pol 1 or Pol 2.

OPERATION

Home Screen Display MASTER

SLAVE

Page 10

USE ONLY HAYWARD®GENUINE REPLACEMENT PARTS

OPERATION CONTINUED

Conguring Master Unit

Relay config.

Filter pump

Extra settings

Reset counters





2WKHUSXPSV



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



S+SULPDU\



5HGR[

S+

$X[

Filtraon Sengs for Master and Slave Units

NOTE:

-It is recommended that the salinity level for each unit is calibrated to read the same value to limit confusion.

-The temperature reading on each unit should be calibrated to read the same value to limit confusion. If the

Master unit is controlling a heater, ensure that the heater is not running when calibrating the two temperature

readings to be the same. When the heater will be running there will be a differential reading between the two

units due to the different points of measurement in the plumbing.

Relay config.

Filter pump

Extra settings

Reset counters





2WKHUSXPSV



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



S+SULPDU\



5HGR[

S+

$X[

Relay config.

Filter pump

Extra settings

Reset counters





2WKHUSXPSV



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



S+SULPDU\



5HGR[

S+

$X[

Relay config.

Filter pump

Extra settings

Reset counters





2WKHUSXPSV



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



S+SULPDU\



5HGR[

S+

$X[

Relay config.

Filter pump

Extra settings

Reset counters





2WKHUSXPSV



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



S+SULPDU\



5HGR[

S+

$X[

1. Enter System settings from the Main Menu.

2. Enter the Service menu from the System Settings.

3. Enter the Password:

4. Select the Relay config. tab.

5. Scroll down to Redox and select Aux 3.

6. Exit the Relay config. menu and select the Dos. pumps tab in the

Service menu.

7. Select Other pumps.

8. Change the “Pump On” time to 999 minutes and the “Pump Off” time

to 2 seconds.

OK OK OK OK

1246

1 2

Master

1. Enter Filtration from the Main Menu.

2. Either select the Auto or Smart Mode if the Master unit is not

controlling a heater and if it is, then Heating or Intelligent Modes can

be selected.

3. Set he desired daily run times and schedules for all modes apart

from Intelligent mode that is based on a 24 hour schedule.

Slave

1. Enter Filtration from the Main Menu.

2. Set the Slave unit to run in Auto Mode ONLY.

3. If the Master unit is set to operate in Auto, Smart, or Heating

modes, set the time schedules on the Slave unit to mirror those of

the Master unit.

4. If the Master unit is set to operate in Intelligent mode, set the time

schedule of the Slave unit to turn on at 00:01 and off at 23:59

(In this scenario the Slave unit will run a filter pump if connected,

for 24 hours per day). The reason to have the Slave unit standing by

ready to chlorinate for 24 hours, is because the Intelligent Mode that

the Master unit is running, is based on automatic on and off times

and depending on the water temperature, the run times will vary.

Relay config.

Filter pump

Extra settings

Reset counters



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



Relay config.

Filter pump

Extra settings

Reset counters



2WKHUSXPSV



3XPSRQ

3XPSRII



VHFV

PLQV



Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward ColorLogic WFBCUS1100 Bedienungsanleitung

Hayward

Hayward Control Station Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Goldline Controls Aqua Logic AQL-P-4 Bedienungsanleitung

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Bedienungsanleitung

Hayward

Hayward CL100 Bedienungsanleitung

Hayward

Hayward Turbo Cell Bedienungsanleitung

Hayward

Hayward Sheer 500 Bedienungsanleitung

Hayward

Hayward AquaRite series Bedienungsanleitung

Hayward

Hayward AQL-CHEM Bedienungsanleitung

Hayward

Hayward S311SX Bedienungsanleitung

Hayward

Hayward OnCommand Bedienungsanleitung

Hayward

Hayward Salt & Swim Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Sense and Dispense Bedienungsanleitung

Hayward

Hayward WFL100 ColorLogic Bedienungsanleitung

Hayward

Hayward Paramount MDX-R3 Programmierhandbuch

Hayward

Hayward ProLogic Bedienungsanleitung

Hayward

Hayward Pool pH Bedienungsanleitung

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Hayward

Hayward XStream CC1000 Bedienungsanleitung

Hayward

Hayward OmniHub Bedienungsanleitung

Hayward

Hayward EasyClear C550 Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung

Silvair

Silvair MESH-CEDRP Bedienungsanleitung

S&P

S&P PCRL80 Bedienungsanleitung