Hayward OmniHub Bedienungsanleitung

Hayward Pool Products

620 Division Street, Elizabeth NJ 07207

Phone (908)-355-7995

www.hayward.com

OmniHub

Pool Automation Control

Installation Manual

Contents

Before you Begin.....................3

Mounting...............................8

Plumbing..............................10

Wiring...................................11

Startup................................23

Conguration........................24

092711 RevA

HLOMNIHUB

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

Changes or modiﬁcations not expressly approved by Hayward could void the user’s authority to

operate this equipment.

NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that interference

will not occur in a particular installation. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the equipment off and on, the user is

encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

-- Consult the dealer or an experienced radio / TV technician for help.

Industry Canada Statement

This Class B digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

The term “IC” before the certiﬁcation / registration number only signiﬁes that the Industry Canada

technical speciﬁcations were met.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Table of Contents

Before you Begin.......................................................................................................3

Overview..................................................................................................................4

Mounting

Wiring Hub.......................................................................................................8

Control Pad......................................................................................................8

Smart Relay......................................................................................................9

Temperature Sensors........................................................................................10

Plumbing................................................................................................................10

Electrical Wiring

High Voltage...................................................................................................12

Low Voltage....................................................................................................18

System Startup.........................................................................................................23

Conﬁguration

Pre-Programmed Conﬁguration........................................................................26

Typical Conﬁguration.......................................................................................27

Advanced Conﬁguration..................................................................................29

Quick Edit..............................................................................................................47

Control Pad Mounting Template.................................................................................57

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Before you Begin

What’s Included

Check that the following components have been included in your package:

• Wiring Hub

• Control Pad

• Smart Relay

• 2 Temperature Sensors

• 15 ft, 2 conductor (red and black) cable for low voltage connection to Wiring Hub from a vari-

able speed pump (VSP) or Heater

• 2 Wiring Whips - 6 ft ﬂexible conduit containing three 12AWG conductors (red, black and

green) for ﬁlter pump and Smart Relay installation. A length of white 12 AWG conductor is

included to replace red for 115 VAC pump and Smart Relay applications

• Input Power Wiring harness and miscellaneous installation hardware

Note that your OmniHub may have been packaged with additional equipment and may contain spe-

ciﬁc installation information on a separate Quick Start guide.

What’s NOT Included

Some of the additional items that you may need to complete an installation include:

Wire

• Wire/conduit for incoming power

• Wire for remote variable speed pump control and other low voltage devices

• Ethernet cable (if not using wiﬁ)

Miscellaneous

• Valve actuator to automate pool functions

• Flow switch for optional pump protection/ﬂow monitoring. A ﬂow switch is required if using

Sense and Dispense accessories

• Mounting hardware for mounting Wiring Hub, Control Pad and Smart Relay

• Cable/cord connectors to provide knockout strain relief

• Wire nut connectors

• USB thumbstick (to update ﬁrmware)

Tools Needed

Phillips and ﬂat screwdrivers Wire cutters and strippers Knife to cut conduit

Drill and drill bits (including 3/8") Pliers Level

Accessory Products - Order Separately

HLH485RELAY Smart Relay used for controlling additional pool equipment

GLX-FLO Flow Switch used to detect water ﬂow

GVA-24 Valve Actuator

2PC Temperature Sensor for 3rd input

USE ONLY HAYWARD GENUINE REPLACEMENT PARTSUSE ONLY HAYWARD GENUINE REPLACEMENT PARTS

HL-CHEM ORP & pH Sensing Kit for monitoring and controlling pool chemistry (requires

GLX-FLO ﬂow switch)

HL-CHEM4-ACID Liquid acid feeder (requires GLX-FLO ﬂow switch)

HL-CHEM4-CHLOR Liquid chlorine feeder (requires GLX-FLO ﬂow switch)

CL200 Chlorine tablet feeder

HLAQR940 Aqua Rite chlorine generator

AQR940/AQR925 Aqua Rite chlorine generator (requires HLAQRPCB)

Overview

The Hayward OmniHub is a web enabled pool automation control with a convenient touchscreen

interface. Automatically and remotely control the pumps, a heaters, valve actuators, pool and yard

lighting, pool chemistry equipment and more. The OmniHub offers the next generation of technology

to manage pool/spa equipment, allowing communication to web connected computers and mobile

devices. You can now conveniently monitor your pool/spa and change settings anytime, and from

anywhere.

Please read this manual thoroughly before attempting to install, conﬁgure or operate this unit. A

Quick Start guide may have also been included to offer concise information speciﬁc to your equip-

ment.

Features

The standard Hayward OmniHub offers the following functionality:

• controls up to 3 variable speed pumps* (VSPs) for pool/spa ﬁltration and water features

• controls up to 3 Smart Relays to turn on/off single speed pumps, pool lights, yard lights, water

features, chemical dispensers and more

• controls up to two valve actuators allowing you to manage two bodies of water (both pool and

spa) or can be used for water features, cleaners, solar heating, etc.

• controls one conventional heater (electric heat pump or gas) and optional solar heater (for single

body of water applications only)

• inputs for up to 3 temperature sensors or external input devices

• built-in wireless to connect to the home’s router/access point (Ethernet port provided for optional

wired connection)

• optional ﬂow switch used to protect pool equipment by detecting water ﬂow

• controls an optional Sense and Dispense module (HL-CHEM) which monitors the pool's pH and

ORP and can dispense acid for pH control and chlorine for ORP control (requires additional equip-

ment)

• controls an optional Hayward Aqua Rite salt chlorinator. If controlled by the OmniHub, the Aqua

Rite must have a HLAQRPCB communication board installed

Optional accessories (page 3) can expand the functionality of the OmniHub. Determine your needs

and select the necessary accessories before you begin the installation.

* If a non-Hayward brand VSP or an older non-supported Hayward VSP will be used, the pump can only operate at one speed.

The pump must be locally programmed to run 24 hrs/day at a ﬁxed speed and the OmniHub will turn it on and off based

on the desired programmed time. Follow instructions to install and function like a single speed pump, using a Smart Relay.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Equipment

Wiring Hub

All incoming/outgoing wiring will be connected to the Wiring Hub. The OmniHub can be powered

by either 230 VAC or 115 VAC. Input power should be constant, not from a timer. If a timer must be

used, set the timer to power the Wiring Hub continuously. For convenience, 6 ft Wiring Whips with

red, white, black and green colored 12AWG wires are included with the OmniHub.

The remaining connections to the Wiring Hub, including the Control Pad, are all low voltage. De-

pending on your installation, these connections could be to a variable speed pump, Smart Relays,

temperature sensors, actuator and a ﬂow switch.

Control Pad

The Control Pad is weather resistant and comes with a 15 ft cord. Its resistive touch screen with ﬂip

down cover is designed to function year round directly in the elements. Because it plugs into the Wir-

ing Hub, it should be mounted close by, but in a location that is convenient for the user to periodically

view and change pool/spa settings. Lastly, the Control Pad contains the Wiﬁ radio and its location

should be considered if planning to use a wireless connection to the home router or access point. A

wireless mobile device (phone, tablet, etc.) could be used to test the signal strength at the intended

mounting location. The Control Pad features a USB connector for ﬁrmware updates and an Ethernet

connector for an optional direct wire connection to your router (if wiﬁ won't be used).

Smart Relay

Smart Relays have a 15 ft communication cable that connects to the Wiring Hub and are used to

control high voltage pool equipment like lights, water features, pumps and more. 115 VAC or 230

VAC power to the intended load must be supplied separately and run through the Smart Relay. Smart

Relays are rated for up to 20 amps at 230 volts.

Temperature Sensors

Depending on your installation, up to 3 temperature sensors may be used. The OmniHub requires

a water temperature sensor for heater operation. If freeze protection is desired, an air temperature

sensor is also required. For solar heating systems, a solar sensor is necessary. Even if your instal-

lation doesn't require the use of temperature sensors, installing water and air sensors provides a

convenience to the user, especially during remote use.

Flow Switch (not included)

An optional ﬂow switch can be used to detect leaks or clogs in the pool/spa plumbing. A ﬂow switch

is required if using chemistry Sense and Dispense accessories.

Overview

Before attempting to install the OmniHub, familiarize yourself with the installation steps on the fol-

lowing pages. Also refer to the sample overview diagrams on page 6. Diagram 1 shows wiring

to a single speed pump and a conventional gas heater. Single speed (and two speed) pumps are

controlled by Smart Relays. In this example the high voltage for the conventional gas heater is wired

in parallel with the Wiring Hub. A Wiring Whip is used for this connection. A separate remote control

connection is made from the Wiring Hub to the heater.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Pump Input Power or

Existing Timeclock

Wiring Hub

(Optional)

Smart Relay 2

Single Speed

Pump

Filter

Valve

Actuator

POOL

FROM

POOL

Comm. to Smart

Relay 1 (15’)

Heater

Remote

Control

Comm. to

Valve

Actuator

To Solar

REMOTE

RELAY

OFFLINE:

ON/OFF

Smart Relay 1

Comm. to Smart

Relay 2 (15’)

Control Pad

To Feature,

Accessory,

Lights, etc.

Wireless

Connection

Ethernet to

Router

Comm. to

Controller (15’)

Sensor 1

(Water Temp.)

Sensor 2

(Air Temp.)

Sensor 3 (Solar OR

External Input)

(Optional)

Flow Switch

REMOTE

RELAY

OFFLINE:

ON/OFF

Wiring Whip from Hub

(gas heaters only)

Heater

Power

from

Smart

Relay

refer to additional information in this

manual if using a two speed or

variable speed ﬁlter pump

Input

Power

Input Power

for Hub and

Heater

(Gas models)

Input Power or

Existing Timeclock

Wiring Hub (Optional)

Smart Relay 2

To Feature,

Accessory,

Lights, etc.

Variable

Speed Pump

Filter

Valve

Actuator

Heater

POOL

FROM

POOL

Power

to VSP

if same

voltage

as Hub

Input Power to

Smart Relay 1

Comm. to Smart

Relay 1 (15’)

Heater

Remote

Control

Comm. to

Valve Actuator

Comm.

to VSP

To Solar

REMOTE

RELAY

OFFLINE:

ON/OFF

Smart Relay 1

Input

Power

Comm. to Smart

Relay 2 (15’)

Control Pad

To Feature,

Accessory,

Lights, etc.

Wireless

Connection

Ethernet to

Router

Comm. to

Controller (15’)

Sensor 1

(Water Temp.)

Sensor 2

(Air Temp.)

Sensor 3 (Solar OR

External Input)

(Optional)

Flow Switch

REMOTE

RELAY

OFFLINE:

ON/OFF

Wiring Whip

Heat pumps require

input power directly

from electrical panel

Diagram 2 shows wiring to a supported VSP and electric heat pump heater. Variable speed pumps

must have constant input power and require a communication connection to the Wiring Hub. In this

example, the high voltage VSP is wired in parallel with the Wiring Hub. Heat pumps, which require a

separate circuit from the electrical panel, only have a remote control connection to the Wiring Hub.

Diagram 1

Diagram 2

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

These Overview diagrams are offered as a guide and it's likely that your installation will require

you to use some combination of two conﬁgurations. Refer to the following pages for speciﬁc wiring

information and note the required voltage for each piece of equipment. Keep in mind that the Wir-

ing Hub can be powered by either 115 VAC or 230 VAC when wiring equipment in parallel. Lastly,

be aware of each circuit breaker's rating and don't exceed their rated load.

Installation

Installation Steps

DANGER of Death, Injury or Property Damage if procedure not followed. Power wiring must

be shut off before attempting to install the OmniHub.

The OmniHub is designed to be mounted outdoors at the pool pad. Both the Wiring Hub and the

Control Pad are water resistant and can be left out for the winter. Details on each installation step

are shown below:

1. Mounting the equipment (page 8)

Wiring Hub

Control Pad

Smart Relay

Temperature sensors

Valve actuators (if applicable)

2. Plumbing (page 10)

General Pool Equipment

Flow Switch

3. Electrical Wiring (page 11)

Wiring Hub power

Grounding

Wiring (Pool Pump Communication, Heater, Smart Relays,Temperature Sensors, Flow Switch,

etc.)

5. System Startup and Firmware Upgrade (page 23)

Your OmniHub may have been packaged with additional equipment and may contain speciﬁc instal-

lation information on a separate Quick Start guide. If so, refer to both this document and your Quick

Start guide for installation instructions.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Mounting the

Equipment

Wiring Hub

The Wiring Hub is contained in a raintight enclosure

that is suitable for outdoor mounting. It must be

mounted a minimum of 6 ft (2 meters) horizontal

distance from the pool/spa (or more, if local codes

require). The Wiring Hub is designed to mount verti-

cally with the knockouts facing downward. Do not

mount the Wiring Hub inside a panel or tightly en-

closed area.

When selecting a location, note that the standard

cables supplied with the optional ﬂow switch, tem-

perature sensors, and actuators are all 15 ft (5m)

long. Additional low voltage connections will have

to be made to the heater and VSP, if used. 230 VAC or 115 VAC input power must also be run to

the Wiring Hub. Try to mount the Wiring Hub in a location where incoming/outgoing wiring will be

easily accessible.

Mount the Wiring Hub on a wall or ﬂat surface. Select mounting hardware that is appropriate for the

mounting surface and material. The Wiring Hub has two keyhole type mounting tabs on the top and

bottom of the enclosure requiring a total of 4 fasteners.

Control Pad

The Control Pad comes with a 15 ft cord and plugs into the Wiring Hub. It should be mounted in a

location that is convenient for the user to view and change pool/spa settings. When considering the

mounting location, make sure there is enough clearance above the enclosure so that the ﬂip door

will be able to be opened fully. Also be sure to allow enough clearance below the Control Pad to

access the USB and Ethernet connectors. For best viewing results, position the Control Pad where it

won't be subjected to direct sunlight.

The Control Pad has two keyhole cutouts on the back of its enclosure. To mount, screw the two

provided fasteners into the mounting surface at the desired location using the template found on

page 57. Tighten until the bottom of the screw heads are 1/8" off the mounting surface. Position the

Control Pad cutouts over the screw and slide the unit downward. You may have to tighten or loosen

the screws slightly to fully engage the screw heads to get a snug ﬁt.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Smart Relay

The Smart Relay is packaged with a single gang electrical box but can also be used with any existing

comparable standard electrical box with a minimum volume of 16.2 in3. If using 115 VAC, make

sure that there is a Neutral line inside the box before installation. If not, you must run a separate

Neutral wire to power the Smart Relay. This is not a concern if using 230 VAC. Note that conduit and

connections to the included plastic box must be non-metallic.

Find a location within 15 ft of the Wiring Hub with convenient access to the pool equipment that

you intend to control with the Smart Relay. Three threaded 1/2" NPT knockouts are provided for

high voltage power coming into the relay and for power out to the pool equipment. A Wiring Whip

is included to aid installation.

The Smart Relay has a manual On/Off button that can be used if communication is lost with the

Wiring Hub. Although this button is not functional during normal operation, mount the Smart Relay in

an accessible location to use this feature in case of communication loss. Refer to page 17 for Smart

Relay LED information.

Mount the Smart Relay to a wall or other ﬂat surface using the mounting holes which are designed

to accommodate #8 screws.

USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Andere Handbücher für OmniHub

Inhaltsverzeichnis

Andere Hayward Beleuchtungsausrüstung Handbücher

Hayward

Hayward Control Station Bedienungsanleitung

Hayward

Hayward 3478 PLDBL3 Bedienungsanleitung

Hayward

Hayward Vistapool Handbuch

Hayward

Hayward GOLDLINE Aqua Rite Pro LS Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Salt & Swim Bedienungsanleitung

Hayward

Hayward AquaRite AQR15 Bedienungsanleitung

Hayward

Hayward SwimPure Plus Technisches Datenblatt

Hayward

Hayward Stainless Steel Niches Bedienungsanleitung

Hayward

Hayward SwimPure Bedienungsanleitung

Hayward

Hayward Goldline Controls Sense and Dispense Total Pool Chemistry... Bedienungsanleitung

Hayward

Hayward OnCommand Bedienungsanleitung

Hayward

Hayward Pro-Grid DE2420EURO Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Hayward

Hayward Sense and Dispense AQL-CHEM Bedienungsanleitung

Hayward

Hayward HL32950VVSP Bedienungsanleitung

Hayward

Hayward Turbo Cell Bedienungsanleitung

Hayward

Hayward OmniPL HLBPRO4SW Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward VR1000 Bedienungsanleitung

Hayward

Hayward EasyClear C550 Bedienungsanleitung

Hayward

Hayward AQL-CHEM Bedienungsanleitung

Hayward

Hayward Pro Logic Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung