Hayward AquaRite 100 Bedienungsanleitung

AquaRite 100®

Troubleshooting Guide

Safety Precautions

Warning

High Voltage Electrocution Hazard

Hazardous voltage can shock, burn, cause serious injury

and or death. To reduce the risk of electrocution and or

electric shock hazards:

•Only qualified technicians should remove the panel

•Replace damaged wiring immediately

•Insure panel is properly grounded and bonded

Table of Contents

How AquaRite 100® works, main display layout, water

chemistry Requirements

Pg.

4-7

How To:

Pg.

8-12

1. Input Voltage Configuration

2. Adjust Daily Chlorine Output

3. Clean Electrolytic Cell

11-12

Troubleshooting:

Pg.

13-36

1. Inadequate Water Flow LED

2. Problem Detected with MIN LED or LED #2

3. Problem Detected with LED # 3 or LED #4

4. Problem Detected with LED # 5,6,7, or 9

5. Problem Detected with LED # 8 or MAX LED

14-16

17-23

24-27

28-31

32-36

Additional Information:

Pg.

37-41

Salt Addition Table 38

Salt Dilution Formula

Replacement Parts List

Reading Serial Numbers 41

AquaRite: How It Works

•The AquaRite 100 Salt Chlorine Generator is

designed to convert 99% pure salt into chlorine

gas (HOCl).

•The conversion occurs in the Electrolytic Cell,

also known as the Cell (used throughout this

guide).

•Power is sent from the AquaRite 100 Control

Center to the Cell when chlorine production is

scheduled (based on time percentage).

•When power is applied to the Cell, conductive

plates produce a field; which in-turn establishes

an electrochemical reaction between Chloride

ions & the water to create Hypochlorous Acid.

AquaRite 100: Display Layout

Inadequate Water Flow LED

Cell Life Low LED

Problem Detected LED

Standing By LED

Generating Chlorine LED

Super Chlorinating LED

Minimum Chlorine Output LED (10%)

DAILY CHLORINE OUTPUT LED’s

Chlorine Output Adjustment Buttons

Super Chlorinate Button

Maximum Chlorine Output LED (100%)

AquaRite 100: Display Function

Illuminates when there is no flow or low

flow

through the Cell

Illuminates when Cell has reached the end

of its expected life

Illuminates if there is a problem with the

unit

Illuminates when unit is waiting for the

filter pump to turn on or is in

-between

generating cycles

Illuminates

when unit is actively generating

chlorine

Illuminates when unit is SUPER

CHLORINATING

The Minimum DAILY CHLORINE OUTPUT

amount of chlorine being generated

Indicates DAILY CHLORINE OUTPUT

settings

Press ( + ) and ( - ) to increase or decrease

the chlorine generation

Boosts DAILY CHLORINE OUTPUT to 100%

for 24 hours

The Maximum

DAILY CHLORINE OUTPUT

amount of chlorine being generated

AquaRite 100: Chemistry Requirements

•Pools 15k gal and below: 1500 – 2700 ppm

•Pools up to 30k gal: 2800 – 4500 ppm (Ideal level 3200 ppm)

Salt Levels

•1.0 – 3.0 ppm

Free Chlorine

•7.2 – 7.8 ppm

•80 – 120 ppm

Alkalinity

•200 – 400 ppm

Calcium Hardness

•Outdoor Pools: 30 – 50 ppm

•Indoor Pools: 0 ppm

Cyanuric Acid (Stabilizer)

•0 ppm

Metals

•-.2 to .2 (0 is best)

Saturation Index

•Less than 200 ppb

Phosphates

•As close to 0 ppb as possible

Nitrates

AquaRite 100®

How To:

How To: Input Voltage Configuration

The AquaRite 100 can be powered by 120 VAC or 240 VAC. Use a multi-

meter to verify voltage in order to determine wire configuration.

120 VAC Wire Colors

Line 1 Black & Violet

Line 2 N/A

Neutral Red & White

Ground Green

240 VAC Wire Colors

Line 1 Black

Line 2 Red

Neutral White & Violet

Ground Green

* Power must be turned off at the circuit breaker before performing any wiring. Follow ALL Local and

NEC electrical codes. To provide safe operation, the AQR100 should be installed by a qualified service

professional and must be properly grounded AND bonded.

NOTE: If the chlorine level does not increase within 24 hours after increasing output, test water using an

independent test kit to determine the current salt, stabilizer, phosphate, and nitrate levels.

NOTE: Output is scaled back to 20% or lower (depending on where the dial is set) at 60°F and chlorine

production stops altogether at 50°F.

How To: Adjust Chlorine Output

The “Daily Chlorine Output” buttons set the level of production during the generating cycle. Generating cycles

occur in 60 minute increments. Each led illuminated (from Min to MAX) represents 10%, or six(6) minutes

of chlorine production time.

Example: The first 4 LED’s being on implies the Cell is producing chlorine 40% of the pump run time; so the

Cell should produce chlorine for the first 24 minutes of each hour before repeating.

Press to decrease

output setting

Press to increase

output setting

Press to Super

Chlorinate

(Temporarily increases

chlorine output to 100%

for 24 hours. Pump must

be on during this time)

Andere Handbücher für AquaRite 100

Inhaltsverzeichnis

Andere Hayward Wasserpumpe Handbücher

Hayward

Hayward XE Series Bedienungsanleitung

Hayward

Hayward NorthStar Bedienungsanleitung

Hayward

Hayward Super II Economy VS SP3011DIVS Bedienungsanleitung

Hayward

Hayward BP100 Bedienungsanleitung

Hayward

Hayward SP1580 Bedienungsanleitung

Hayward

Hayward Super Pump 700 Series Bedienungsanleitung

Hayward

Hayward HL32900VSP Bedienungsanleitung

Hayward

Hayward Booster Pump Bedienungsanleitung

Hayward

Hayward EcoStar SP3400VSP Bedienungsanleitung

Hayward

Hayward TriStar VS 950 Bedienungsanleitung

Hayward

Hayward TriStar VS SP3215VS Bedienungsanleitung

Hayward

Hayward LifeStar VS Bedienungsanleitung

Hayward

Hayward EcoStar Bedienungsanleitung

Hayward

Hayward TriStar SP3200 Series Bedienungsanleitung

Hayward

Hayward EcoStar SP3400VSP Bedienungsanleitung

Hayward

Hayward LifeStar Series Bedienungsanleitung

Hayward

Hayward Super II Bedienungsanleitung

Hayward

Hayward Super Pump Series Bedienungsanleitung

Hayward

Hayward POWER-FLO II Series Bedienungsanleitung

Hayward

Hayward TriStar HCP3205C Bedienungsanleitung

Hayward

Hayward SUPERPOOL POWPSCP05 Bedienungsanleitung

Hayward

Hayward HCP3020VSP Bedienungsanleitung

Hayward

Hayward IS3206VSP3 Bedienungsanleitung

Hayward

Hayward WG1031HF2PAK2 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung