Hayward EcoStar SP3400VSP Bedienungsanleitung

EcoStar®&

EcoStar SVRS®

Technical &

Installation Guide

SP3400VSP

SP3400VSPVR

Drive r1.13

Interface r3.0.8 residential

Interface r3.0.8C commercial

Table of Contents

Safety Precautions Page 1

Installation Page 2-14

Programming Page 15-29

Operation Page 30-31

Programming Scenarios Page 32

Disassembly/Assembly Page 33-38

Password/Commercial Page 39-40

Diagnostic Menu Page 41

•Read and follow all instructions in the owner’s manual and on the equipment.

Failure to follow instructions can cause severe injury and/or death.

•This product should be installed and serviced only by a qualified professional.

•All electrical wiring MUST be in conformance with all applicable local codes,

regulations, and the National Electric Code (NEC). Hazardous voltage can shock,

burn, and cause death or serious property damage. To reduce the risk of electric

shock, do NOT use an extension cord to connect unit to electric supply. Provide a

properly located electrical receptacle. Before working on drive or motor, turn off

power supply to the drive.

•Failure to bond drive to pool structure will increase risk for electrocution and

could result in injury or death. To reduce the risk of electric shock, see installation

instructions and consult a professional electrician on how to bond drive. Also,

contact a licensed electrician for information on local electrical codes for bonding

requirements.

Page 1

Safety Precautions

Installation - Plumbing

New Pools: When installing the EcoStar on a new pool, care should

be taken to ensure proper pipe and equipment sizing to

handle the maximum flow required (fig 1).

Existing Pools: When installing the EcoStar on existing pools, care should

be taken to insure the maximum flow does not exceed the

capacity of the pipe and equipment*(fig 1).

MAXIMUM RECOMMENDED SYSTEM FLOW RATE BY PIPE SIZE

1.5”

51gpm 8fps

38gpm 6fps

2”

84gpm 8fps

63gpm 6fps

2.5”

120gpm 8fps

89gpm 6fps

3”

184gpm 8fps

138gpm 6fps

* Refer to equipment manuals for flow rates. Figure 1

Page 2

Note: length of pipe (L) between pump suction port and

first elbow or fitting should be at least 5 times pipe size.

Installation - Electrical

Remove the electrical cover plate as shown below

(fig 2, 3 & 4)

Figure 2 Figure 3 Figure 4

Page 3

Note: If power is removed from the pump, all settings will be protected for at least 5 years.

Installation –Electrical

Internal wiring locations

Figure 5

Page 4

Wiring plug for

wall mounted

interface

Wiring connection

for incoming motor

wires

Wiring plug for relay

connected controls &

stop switch

Wiring plug for data link with

Hayward/Goldline compatible

software controls

Wire connection

for incoming line

voltage (230v)

Channel for

running low

voltage data cable

Installation –Electrical/High Voltage

High Voltage Wiring terminals (L1 & L2)

1. Voltage: 230 VAC, 60Hz, Single Phase.

2. Breaker, wire size would be determined

by the NEC and local code requirements.

Ground Wire

Terminal.

It is below high

voltage wires

and should be

connected first.

Conduit

Connections

There are two on

the pump. One

for high voltage

and the other for

the low voltage

data cable.

Make sure the unit is both bonded and grounded!

Figure 6

Page 5

Note: When connecting high

voltage for an EcoStar that is

data connected to a Hayward/

Goldline control, voltage

needs to come directly from a

breaker in the control, or in

the case of an OnCommand,

directly from the main or sub-

panel and not from the filter

pump relay.

Bonding Lug

Installation–Interface removal/positioning

1. Remove the two screws as

shown (fig 7).

2. Remove the interface assembly

as shown (fig 8).

3. Reposition interface assembly

as shown (fig 7, 9, 10 & 11) and

re-secure with the two screws

(fig 7).

The interface assembly on the

EcoStar can be configured in

four different positions.

Page 6

Figure 11

Figure 7

Figure 9 Figure 10

Figure 8

Installation–Interface /Wall mount

1. Wall mount kit is included with the EcoStar and includes blank cover, mounting bracket and new terminal

block for connecting to the interface assembly. Maximum 500’ for data cable used for wall mount or control

connection.

2. After removal of the interface assembly (Page 7) remove the plug connecting the drive to the interface (fig 12).

3. Plug is permanently attached (fig 13), install the blank cover over the plug (fig 14).

Figure 14Figure 13

Figure 12

Page 7

Installation–Interface /Wall Mount

4. The data cable needs to be routed through the second (low voltage) conduit opening (fig 15).

5. Remove the wall mounting data plug from the electrical compartment as shown (fig 16).

6. You will need to procure a six wire data cable, as short as possible, and attach the wires to the data

plug as shown (fig 17) taking care to note the color and corresponding number next to the data plug (fig

15).

Figure 15

Figure 16 Figure 17

Page 8

Data cable is

routed separate of

high voltage and

in it’s own

channel within the

motor electrical

compartment

Data Plug

Andere Handbücher für EcoStar SP3400VSP

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Wasserpumpe Handbücher

Hayward

Hayward Max-Flo II Series Leitfaden

Hayward

Hayward SP1580 Bedienungsanleitung

Hayward

Hayward Turbo Flo II Bedienungsanleitung

Hayward

Hayward SUPERPOOL POWPSCP05 Bedienungsanleitung

Hayward

Hayward Max-Flo™ Bedienungsanleitung

Hayward

Hayward TriStar SP3207EE Bedienungsanleitung

Hayward

Hayward PowerFlo VS 300 Bedienungsanleitung

Hayward

Hayward LifeStar Series Bedienungsanleitung

Hayward

Hayward AquaRite 100 Bedienungsanleitung

Hayward

Hayward MaxFlo SP2806W Bedienungsanleitung

Hayward

Hayward 3200 Series Bedienungsanleitung

Hayward

Hayward TriStar VS 950 Omni Bedienungsanleitung

Hayward

Hayward VS Omni Administratorhandbuch

Hayward

Hayward TriStar VS 950 Bedienungsanleitung

Hayward

Hayward XE Series Bedienungsanleitung

Hayward

Hayward PowerFlo Matrix Bedienungsanleitung

Hayward

Hayward SP2616VS Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward LifeStar MV Series Handbuch

Hayward

Hayward Pro-Grid Bedienungsanleitung

Hayward

Hayward TriStar VS 900 Bedienungsanleitung

Hayward

Hayward IS3206VSP3 Bedienungsanleitung

Hayward

Hayward Booster Pump Bedienungsanleitung

Hayward

Hayward SP32950VSP Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung