Hayward SwimPro SWP120551 Bedienungsanleitung

CENTRIFUGAL PUMPS

SwimPro®

OWNER’S MANUAL

SAVE THIS OWNER’S MANUAL

WARNING: Electrical Hazard. Failure to follow

instructions can result in serious injury or death.

FOR USE WITH SWIMMING POOLS

WARNING –Disconnect the pump from the main power supply completely before servicing the pump or filter.

WARNING –All electrical connections must be done by a qualified electrician according to local electrical regulations

and AS/NZS 3000 Wiring Rules .

WARNING –This Product should be installed and serviced only by a qualified professional.

WARNING –Read and follow all instructions in this owner’s manual and on the equipment. Failure to follow

instructions can cause serious injury or death.

This document should be given to the owner of the swimming pool and must be kept by the owner in a safe place.

WARNING –Be certain the pump is only plugged into a 230 V ± 10% outlet that is supplied through a Residual Current

Device (RCD or Safety Switch) with a residual operating current not exceeding 30mA or supplied by an isolating transformer.

WARNING –Use a motor bonding lug to connect motor with other bonded parts using the appropriate size conductor

as required by electrical codes.

WARNING –If the supply cord is damaged it must be replaced by the manufacturer, service agent, or similarly qualified

persons in order to avoid a hazard.

WARNING –Do not operate the swimming pool pump if the power cord or the housing of the motor connection box is

damaged. This can cause an electric shock. A damaged power cord or motor connection box must be replaced by a service

agent or a similarly qualified person immediately in order to avoid a hazard.

WARNING –The appliance is not intended for use by persons (including children) with reduced physical,

sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction

concerning use of the appliance in a safe way and understand the hazards involved.

WARNING

objects away from openings and moving parts.

WARNING –Cleaning and user maintenance shall not be made by childrenwithout supervision.

WARNING –The pump is intended for continuous operation at Maximum Water temperature 35°C.

WARNING –Use Only Genuine Hayward Replacement Parts.

WARNING –This pump is equipped with Automatic Thermal Overload Protection. The motor will automatically shut-

off under normal conditions, before heat damage build-up, due to improper operating condition, can occur. The motor

will automatically restart when a safe heat level is reached.

WARNING –This pool motor is NOT equipped with a Safety Vacuum Release System (SVRS). SVRS helps prevent

drowning due to body entrapment on underwater drains. In some pool configuration, if a person’s body covers the drain, the

person can be trapped by suction. Depending on your pool configuration, a SVRS may be required to meet local requirements.

Zone 1 or 2 ok

ZONE 0

GENERAL

Install the pump at a convenient distance from the edge of the pool to minimize the distance between the suction point and

the pump so as to avoid pointless and excessive load losses in the hydraulic circuit.

This pump can be mount in swimming pool zone 1 or further away as per the conditions of AS/NZS 3000 Wiring Rules.

Install the pump in a ventilated, dry and well drained area that will not flood when it rains. The motor requires air to flow freely

around it to provide natural ventilation for cooling. If installed within an outer enclose or beneath the skirt of a hot tub or spa,

adequate ventilation and free circulation of air must be provided to prevent overheating of the motor.

The pump has to be installed, so that the plug and the wall socket outlet is easily visible and accessible.

The pump must be permanently mounted to a concrete base using lag screws suitable for concrete where pilot holes have

been drilled. Locking washers must be supplied to prevent loosening of the mounting lag screws over time. If the pump is

to be mounted to a wooden deck then lag screws suitable for wood must be used - with lock washers to prevent loosening

over time.

The acoustic level of the Hayward pumps is lower than 70 dB (A).

ELECTRICAL CONNECTION

Make sure that the power supply voltage required by the motor corresponds to that of the distribution network and that the

power supply cables matches the power and current of the pump as in accordance with AS/NZS 3000 Wiring Rules.

Any changes to or installation of power outlets must be done by a qualified electrical contractor.

The supply power is to be supplied by an isolating transformer or supplied through a residual current device (RCD)

having a rated residual operating current not exceeding 30 mA.

The single phase motors fitted to our pumps are provided with thermal protection. This protection operates on an overload

or in the event of abnormal heating of the motor coil and is reset automatically when the winding temperature drops which

allows the pump to automatically restart without warning.

STARTING AND PRIMING INSTRUCTIONS

Fill strainer housing with water to suction pipe level. Never operate the pump without water. Water acts as a coolant and

lubricant for the mechanical shaft seal.

Open all suction and discharge valves, as well as air bleed (if available) on filter. (The air that is to be displaced from the

suction line must have someplace to go).

Turn on power and allow a reasonable time for priming. Five minutes is not unreasonable. (Priming time depends on suction

lift and horizontal length of suction piping). If pump will not start, or will not prime, see TROUBLE SHOOTING GUIDE.

MAINTENANCE

1. Clean strainer basket regularly. Do not strike basket to clean. Inspect strainer cover gasket regularly and replace as

necessary.

2. Hayward pumps have self-lubricating motor bearings and shaft seals. No lubrication is necessary

3. Keep motor clean. Insure air vents are free from obstruction.

4. Occasionally, shaft seals become damaged or worn and must be replaced.

5. Except for cleaning activities, any repairing, servicing and maintenance has to be performed by a Hayward authorized

service agent or a similarly qualified person.

STORAGE

1. Drain pump by removing drain plug(s) and store in strainer basket.

2. Disconnect electrical wires and pipe connections, and store pump in a dry, well-ventilated room. Or, as a minimum

precaution: Disconnect electrical wires. Remove four bolts holding bracket and motor assembly to Strainer/Housing

and store assembly in a dry, well-ventilated room. Protect remaining Strainer/Housing assembly from the elements by

covering.

NOTE: Before Re-Activating pump, thoroughly clean and remove scale, dirt, etc.

A) Motor won’t start - Check for:

TROUBLE SHOOTING GUIDE

1. Power cord is plugged into power outlet, open switches or relays, blown circuit breakers or fuses.

2. Manually check rotation of motor shaft for free movement and lack of obstruction.

B) Motor cuts out - Check for: (Recommend contacting service agent or similarly qualified person)

1. Damaged power cord, plug, or power outlet.

2. Low voltage at motor (frequently caused by undersized wiring).

3. Binding and overload. (Amperage reading.).

NOTE Your pump motor is equipped with Automatic Thermal Overload Protection. The motor will automatically shut-off,

under conditions before heat damage build-up, due to an improper operating condition, can occur. The motor will auto-

restart when safe heat level is reached.

C) Motor hums, but does not start - Check for:

1. Open capacitor or debris jammed in the impeller (Contact service agent or similarly qualified person).

D) Pump won’t prime:

1. Make sure pump strainer/housing is filled with water, and that cover gasket is clean and properly seated. Tighten hand

nuts.

2. Make sure all suction and discharge valves are open and unobstructed, and that pool water level is above all suction

openings.

3. Block off suction as close to pump as possible and determine if pump will develop a vacuum.

a) If pump does not develop vacuum, and pump has sufficient “priming water”:

1. Tighten all bolts and fittings on suction side.

2. Check voltage to make sure pump is up to speed.

3. Open pump and check for clogging or obstruction.

4. Remove and replace shaft seal.

b) If pump develops a vacuum, check for blocked suction line or strainer, or air leak in suction piping.

E) Low flow - Generally, Check for:

1. Clogged or restricted strainer or suction line; undersized pool piping.

2. Plugged or restricted discharge line of filter (high discharge gauge reading).

3. Air leak in suction (bubbles issuing from return fittings).

4. Pump operating under speed (low voltage).

5. Plugged or restricted impeller.

F) Noisy pump - Check for

1. Air leak in suction causing rumbling in pump.

2. Cavitation due to restricted or undersized suction line and unrestricted discharge lines.

Correct suction condition or throttle discharge lines, if practical.

3. Vibration due to improper mounting, etc.

4. Foreign matter in pump housing.

5. Motor bearings made unserviceable by wear, rust, or continual overheating.

Specification Table

Pump

Reference motor

Nominal power

Voltage

Frequency

Phase

Amperage

Capacitor

Maximum Total

Head

SWP120551

610 W

230 V

50 Hz

1 Phase

2,6 A

18 µF, 450 V

14,1 M

SWP120751

790 W

230 V

50 Hz

1 Phase

3,4 A

18 µF, 450 V

14,6 M

SWP121051

920 W

230 V

50 Hz

1 Phase

4,0 A

18 µF, 450 V

15,7 M

SWP121551

1110 W

230 V

50 Hz

1 Phase

4,8 A

30 µF, 450 V

16,8 M

1 2 14

3 17

4 13

9 10

N°

SP81002WAU

SP81003WAU

SP81004WAU

SP81005WAU

SP81006WAU

SP81007WAU

SPX8100LDS

SPX8100S

SPX8100M

SPX8100AA

SPX1700FG

GMX600F

SPX8100R

SPX8100B

SPX8118T

SPX8125T

SPX8137T

SPX8155T

SPX8175T

SPX81110T

SPX1600Z2

SPX8100E

6060XZ1

SPX81018Z1CAU

SPX81025Z1CAU

SPX81037Z1CAU

SPX81055Z1CAU

SPX81075Z1CAU

SPX81110Z1CAU

SPX8100Z1

SPX8100UNBPAK

SPX8100UNSAUPAK

SPX8100UNO

HOUSING BOLT TORQUE PATTERN

50 - 60 INCH LBS

5.6 - 6.8 N m

Hayward and Powerline by Hayward are registered

trademarks of Hayward Industries, Inc.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Wasserpumpe Handbücher

Hayward

Hayward LifeStar Series Bedienungsanleitung

Hayward

Hayward PowerFlo Matrix Bedienungsanleitung

Hayward

Hayward SP32950VSP Bedienungsanleitung

Hayward

Hayward VL Series Bedienungsanleitung

Hayward

Hayward ISVL1285 Bedienungsanleitung

Hayward

Hayward OmniLogic Bedienungsanleitung

Hayward

Hayward SP1580 Bedienungsanleitung

Hayward

Hayward MaxFlo SP2806W Bedienungsanleitung

Hayward

Hayward HL2350020VSP Bedienungsanleitung

Hayward

Hayward Super II Beilage

Hayward

Hayward SwimPro Series Bedienungsanleitung

Hayward

Hayward HCP3000 Series Bedienungsanleitung

Hayward

Hayward HCP3020VSP Bedienungsanleitung

Hayward

Hayward WG1031HF2PAK2 Bedienungsanleitung

Hayward

Hayward Max-Flo™ Bedienungsanleitung

Hayward

Hayward Pro-Grid Bedienungsanleitung

Hayward

Hayward HL32900VSP Bedienungsanleitung

Hayward

Hayward EcoStar Produktinformationsblatt

Hayward

Hayward SP26115VSP Bedienungsanleitung

Hayward

Hayward LifeStar VS Bedienungsanleitung

Hayward

Hayward Super II SP3000 ECO Series Bedienungsanleitung

Hayward

Hayward Super II Bedienungsanleitung

Hayward

Hayward Turbo Flo II Bedienungsanleitung

Hayward

Hayward Maxflo VS SP2303VSP Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung