Hayward SwimPro Series Bedienungsanleitung

SW1275, SW1275X,

SW1275X5

IMPORTANT SAFETY INSTRUCTIONS

When installing and using this electrical equipment, basic safety precautions should always be followed,

including the following: Failure to follow instructions may result in injury.

READ AND FOLLOW ALL INSTRUCTIONS

WARNING - To reduce risk of injury, do not permit children to use this product unless they are closely supervised at all times.

CAUTION - This pump is U.L. listed for permanently installed pools and may also be used with hot tubs and spas if so marked.

It is not U.L. listed for storable pools. A permanently installed pool is constructed in or on the ground and cannot be readily

disassembled for storage. A storable pool is constructed so that it may be readily disassembled for storage and reassembled to

its original integrity.

If installed within an outer enclosure or beneath the skirt of a hot tub or spa, adequate ventilation and free circulation of air must

be provided to prevent overheating of the motor.

Use motor bonding lug to connect the motor with other bonding parts using a #8 AWG conductor as required by electrical codes.

NOTE: If your pump is equipped with a 3 ft. (1 m) cord and twist lock plug, items 5 through 8 apply.

WARNING - Risk of Electric Shock. Connect only to a grounding-type receptacle protected by a ground fault circuit interrupter

(GFCI). Contact a qualified electrician if you cannot verify that the receptacle is protected by a GFCI.

Do not bury cord. Locate cord to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

WARNING - To reduce the risk of electric shock, replace damaged cord immediately.

WARNING - To reduce the risk of electric shock, do not use extension cord to connect unit to electric supply; provide a properly

located outlet.

SAVE THESE INSTRUCTIONS

Forbestpump performance, locate thesystembelow the pool water line and as

close to the pool as practical. If you own an above-ground pool, NOTE:

ANSI/NSPI-4 Article V, standard for above-ground and

on-ground pools, advises that components such as the filtration

system, pumps and heater be positioned so as to prevent their

being used as means of access to the pool by young children.

Makesure suction joints are tight. Suction pipe should be aslarge or larger than

discharge pipe.

Damp,non-ventilatedlocationsshouldbeavoided.Motorsrequirefreecirculation

of air to aid in cooling.

Ensurethattheelectricalsupplyavailableagreeswiththemotor’s voltage,phase

and cycle, and that wire size is adequate for the HP (KW) rating and distance

from power source. Motor must always be properly grounded. If cord connected,

use only a properly grounded outlet.

Fill strainer housing with water to suction pipe level. Never operate the pump

withoutwater. Wateracts as a coolant and lubricant for the mechanical shaft seal.

CAUTION: All suction and discharge valves must be open when

starting the system. Failure to do so could cause severe personal

injury and/or property damage.

Turn on power and allow a reasonable time forpriming. Priming time depends on

suctionliftandhorizontal lengthof suctionpiping.Ifthepumpwillnotstart,orwill

not prime, see TROUBLE SHOOTING GUIDE on back page.

NOTE: Electrical circuits must be protected by proper size ground

fault circuit interrupter (GFCI) as required by applicable electrical

codes. All electrical wiring must be performed by qualified

personnel, and must conform to local codes and regulations.

ISSW1275-99

DWG.

NO. DESCRIPTION

PART NUMBER

NO.

REQ’D. MODEL

SW1275

MODEL

SW1275X, SW1275X5

(With Strainer)

---

Bolt, No. 10-24 Hex. Head

Housing Cover*

Housing Gasket

Impeller

Seal Assembly

Pump Housing

Nut, No. 10-24 Hex.

Motor

Strainer Housing

O-Ring

Basket

Strainer Cover O-Ring--For Clear Lexan Cover

Strainer Cover, Clear Lexan®

Drain Plug w/Gasket

Strainer Shim Ring (Horizontal Outlet Pumps Only)

SPX1500N2

SPX1500B

SPX1500H

SPX1500F

SPX1500KA

SPX1500AA

SPX1500Y2

SPX1510Z1E

SPX1500CA

SPX1500W

SPX1500LX

SPX1500P

SPX1500D2

SPX1700FG

SPX1500X1

SPX1500N2

SPX1500B

SPX1500H

SPX1500F

SPX1500KA

SPX1500AA

SPX1500Y2

SPX1510Z1XE (SW1275X)

SPX1515Z1E (SW1275X5)

SPX1500CA

SPX1500W

SPX1500LX

SPX1500P

SPX1500D2

SPX1700FG

SPX1500

*For Housing Cover with integral drain plug, order SP1500B1.

1. Clean strainer basket regularly. Do not strike basket to clean. Inspect

strainer cover gasket regularly and replace as necessary.

2. SwimPro pumps have self-lubricating motor bearings and shaft seals.

No lubrication is necessary.

3. Keep motor clean. Ensure air vents are free from obstruction.

4. Occasionally, shaft seals must be replaced, due to wear or damage.

See instructions.

GENERAL

Exercise extreme care in handling and installing the new

seal and ceramic seat assembly.

The lapped and polished surfaces may easily be damaged

by dirt or scratching.

For safety, all service must be performed with all power shut off.

Remove pump and motor assembly from piping system.

Remove pump housing cover (with strainer attached) by removing

the seven (7) housing bolts and nuts which fasten housing cover

to pump housing. The impeller is now exposed.

To remove impeller, insert screwdriver in slot at end of motor.*

Hold screwdriver so as to keep shaft from turning, and rotate the

impeller in a counterclockwise direction. The spring portion of the

seal assembly is now exposed.

Note carefully the position of the spring seal and pull it off the

impeller.

To remove the stationary (ceramic seat) part of the seal assembly:

a. Loosen the four (4) motor securing bolts and

disengage the motor from the pump housing.

b. With motor removed, press the clear plastic and

ceramic seat assembly out of the pump housing

recess. If tight, tap lightly from the “motor” side.

Clean and lubricate the impeller hub shaft and pump housing seal

recess with a dilute solution of non-granulated liquid-type soap.

Gently wipe the polished face of the new ceramic seat with a soft,

dry cotton cloth.

Press the new spring portion of the assembly onto the impeller,

black polished surface facing away from the impeller.

Carefully press ceramic seat, with O-ring, into clear plastic seat

retainer--polished surface facing out. Be sure O-ring is in place on cut

ridge of clear plastic retainer. Press plastic retainer, with ceramic seat

inside, into recess of pump housing--O-ring end first. Replace the

assembly firmly and evenly.

Carefully insert the motor shaft through the seat assembly and

secure motor to pump housing with four (4) motor securing bolts.

(Be sure motor base is positioned properly.)

Screw the impeller, with spring seal, onto the motor shaft, hand

tight, by turning clockwise.

Clean rubber gasket (replace if necessary) and fasten housing cover

to pump housing with seven (7) bolts and nuts. Tighten bolts and

nuts alternately and evenly.

Reconnect pump to piping system. Be sure to fill stainer with water

before restarting.

A separate electrical circuit, utilizing a rating as above, is recommended.

*For A.O. Smith Canopy Motors: Remove motor end cover and carefully apply wrench to flat on motor shaft to hold shaft from turning.

10.

11.

12.

Consult your local SwimPro dealer. No pumps or motors may be returned

directly to the factory without expressed written authorization from

Hayward Pool Products.

ELECTRICAL GUIDE - 60 CYCLE MOTORS - SINGLE PHASE

MOTOR

HP KW VOLTS CIRCUIT BREAKER

RATINGS—AMPS BRANCH FUSETRON

RATINGS—AMPS

RECOMMENDED WIRE SIZE

0-50’

1/2

3/4

1-1/2

.37

.55

.75

1.10

115

Pump and motor must be protected from freezing. Shut off all electric

power. Disconnect cord/electrical connections and plumbing connections.

Drain thoroughly and clean out any debris. Store pump and motor in a

dry, well-ventilated room.

No.

TROUBLE SHOOTING GUIDE

MOTOR WON’T START

MOTOR CUTS OUT

MOTOR HUMS, BUT DOES NOT START

PUMP WON’T PRIME

LOW FLOW

NOISY PUMP

1. Check for improper or loose connections, open switches or relays, blown circuit breakers or fuses.

2. Manually check rotation of motor shaft for free movement and lack of obstruction.

1. Wiring, loose connections, etc.

2. Low voltage at motor (frequently caused by undersized wiring).

3. Binding and overload (Amperage reading).

Note: Your SwimPro pump motor is equipped with Automatic Thermal Overload Protection. The motor

will automatically shut-off, under normal conditions, due to an improper operating condition,

before heat damage build-up can occur. The motor will auto-restart when safe heat level is

reached.

1. Centrifugal switch stuck in open position.

2. Binding of motor shaft.

1. Make sure strainer cover is locked firmly in position.

2. Make sure all suction and discharge lines and valves are open and unobstructed, and that pool water

level is above all suction openings.

3. Block off suction as close to pump as possible and determine if pump will develop a vacuum.

a. If pump develops a vacuum, check for blocked suction line or strainer, or air leak in suction piping.

b. If pump does not develop a vacuum and pump has sufficient “priming water”:

(1) Tighten all bolts and fittings.

(2) Check voltage to make sure pump is up to speed.

(3) Open pump and check for clogging or obstruction.

(4) Remove and replace shaft seal.

1. Clogged or restricted strainer or suction line; undersized pool piping.

2. Plugged or restricted discharge line of filter (high discharge gauge reading).

3. Air leak in suction (bubbles issuing from return fittings).

4. Pump operating underspeed (low voltage).

5. Plugged or restricted impeller.

1. Air leak in suction causing rumbling in pump.

2. Cavitation due to restricted or undersized suction line and unrestricted discharge lines. Correct suction

condition or throttle discharge lines, if practical.

3. Vibration due to improper mounting, etc.

4. Foreign matter in pump housing.

5. Motor bearings made unserviceable by wear, rust or continual overheating.

SwimPro by Hayward, Elizabeth, NJ 07207 Printed on recycled paper

Rev. 1/99

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Hayward Wasserpumpe Handbücher

Hayward

Hayward Turbo Flo II Bedienungsanleitung

Hayward

Hayward AquaRite 100 Bedienungsanleitung

Hayward

Hayward Max-Flo II Series Leitfaden

Hayward

Hayward SP32950VSP Bedienungsanleitung

Hayward

Hayward NorthStar Bedienungsanleitung

Hayward

Hayward Super Pump Series Bedienungsanleitung

Hayward

Hayward Super II SP3000 ECO Series Bedienungsanleitung

Hayward

Hayward BP100 Bedienungsanleitung

Hayward

Hayward XE Series Bedienungsanleitung

Hayward

Hayward VS Omni Administratorhandbuch

Hayward

Hayward IS3206VSP3 Bedienungsanleitung

Hayward

Hayward TriStar VS 950 Omni Bedienungsanleitung

Hayward

Hayward LifeStar Series Bedienungsanleitung

Hayward

Hayward XE Series Bedienungsanleitung

Hayward

Hayward Super Pump 700 Series Bedienungsanleitung

Hayward

Hayward Super II Bedienungsanleitung

Hayward

Hayward EcoStar SP3400VSP Bedienungsanleitung

Hayward

Hayward Maxflo VS SP2303VSP Bedienungsanleitung

Hayward

Hayward ISVL1285 Bedienungsanleitung

Hayward

Hayward XE Series Bedienungsanleitung

Hayward

Hayward HCP3000 Series Bedienungsanleitung

Hayward

Hayward WG1031HF2PAK2 Bedienungsanleitung

Hayward

Hayward TriStar HCP3205C Bedienungsanleitung

Hayward

Hayward LifeStar VS Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung