HBM T10F Bedienungsanleitung

Mounting Instructions

English

T10F

Hottinger Baldwin Messtechnik GmbH

Im Tiefen See 45

D-64239 Darmstadt

Tel. +49 6151 803-0

Fax +49 6151 803-9100

[email protected]

www.hbm.com

Mat.: 7-2001.1510

DVS: A0608-14.0 HBM: public

02.2015

EHottinger Baldwin Messtechnik GmbH.

Subject to modifications.

All product descriptions are for general information only.

They are not to be understood as a guarantee of quality or

durability.

T10F A0608-14.0 HBM: public 3

English

1 Safety instructions 6........................................

2 Markings used 11............................................

2.1 The markings used in this document 11..........................

2.2 Symbols on the product 12.....................................

3 Torque flange versions 13....................................

4 Application 14...............................................

5 Structure and mode of operation 15...........................

6 Mechanical installation 17....................................

6.1 Conditions on site 19..........................................

6.2 Installation orientation 19......................................

6.3 Installation options 20.........................................

6.3.1 Installation without dismantling the antenna ring 21................

6.3.2 Installation with subsequent stator mounting 22...................

6.3.3 Installation example with couplings 23...........................

6.3.4 Installation example with joint shaft 23...........................

6.4 Mounting the rotor 24..........................................

6.5 Mounting the stator 28.........................................

6.6 Installing the clamp fixture 31...................................

6.7 Fitting the slotted disc (speed measuring system) 33..............

6.8 Aligning the stator (speed measuring system) 34..................

7 Electrical connection 37......................................

7.1 General information 37........................................

7.1.1 FCC and IC compliant installation for US and

Canada installation only 38.....................................

7.2 Shielding design 39...........................................

7.3 Option 2, code KF1 41........................................

7.3.1 Adaptation to the cable length 41...............................

4A0608-14.0 HBM: public T10F

7.4 Option 2, code SF1/SU2 43....................................

7.5 Supply voltage 46.............................................

8 Calibration 48...............................................

8.1 Calibration option 2, code KF1 49...............................

8.2 Calibration option 2, code SF1/SU2 49...........................

9 Settings 50..................................................

9.1 Torque output signal, code KF1 51..............................

9.2 Torque output signal, code SF1/SU2 51.........................

9.3 Setting up the zero point 51....................................

9.4 Functional testing 52..........................................

9.4.1 Power transmission 52........................................

9.4.2 Aligning the speed module 53..................................

9.5 Setting the pulse count 55.....................................

9.6 Vibration suppression (hysteresis) 56............................

9.7 Form of speed output signal 56.................................

9.8 Type of speed output signal 58.................................

10 Loading capacity 59.........................................

10.1 Measuring dynamic torque 59..................................

11 Maintenance 61..............................................

11.1 Speed module maintenance 61.................................

12 Dimensions 62..............................................

12.1 Rotor dimensions 62..........................................

12.2 Stator dimensions 64..........................................

12.3 Mounting dimensions 66.......................................

T10F A0608-14.0 HBM: public 5

13 Order numbers, accessories 68...............................

14 Specifications 70............................................

15 Supplementary technical information 78......................

15.1 Output signals 78.............................................

15.1.1 Output MD torque (connector 1) 78..............................

15.1.2 Output N: Speed (connector 2) 79...............................

15.1.3 Connector 2, double frequency, stat. direction of rotation signal 80..

15.2 Axial and radial run‐out tolerances 81............................

15.3 Additional mechanical data 82..................................

Safety instructions

6A0608-14.0 HBM: public T10F

1 Safety instructions

FCC Compliance & Advisory Statement

Important

Any changes or modification not expressly approved by

the party responsible for compliance could void the user's

authority to operate the device. Where specified addi

tional components or accessories elsewhere defined to

be used with the installation of the product, they must be

used in order to ensure compliance with FCC regulations.

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

this device may not cause harmful interference, and (2)

this device must accept any interference received, includ

ing interference that may cause undesired operation.

The FCC identifier or the unique identifier, as appropri

ate, must be displayed on the device.

Model Measuring range FCC ID IC

T10S2TO6

50 Nm, 100 Nm, 200 Nm

2ADAT-T10S2TOS6 12438A-T10S2TOS6

500 Nm, 1 kNm

2 kNm, 3 kNm

5 kNm

10 kNm

The FCC ID number in dependence of measuring range.

Safety instructions

T10F A0608-14.0 HBM: public 7

Fig. 1.1 Location of the label on the stator of the device

The preferred position of the FCC label is on the type

plate. If this is not possible for reasons of space, the

label can be found on the rear of the stator housing.

Model: 2ADAT-T10S2TOS6

FCC ID: 2ADAT-T10S2TOS6

IC: 12438AT10S2TOS6

This device complies with part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause unde

sired operation.

Fig. 1.2 Label example with FCC ID and IC number

Industry Canada IC

This device complies with Industry Canada standard

RSS210.

This device complies with Industry Canada license-ex

empt RSS standard(s). Operation is subject to the follow

ing two conditions: (1) this device may not cause interfer

ence, and (2) this device must accept any interference,

including interference that may cause undesired opera

tion of the device.

Safety instructions

8A0608-14.0 HBM: public T10F

Cet appareil est conforme aux normes d'exemption de

licence RSS d'Industry Canada. Son fonctionnement est

soumis aux deux conditions suivantes : (1) cet appareil

ne doit pas causer d'interférence et (2) cet appareil doit

accepter toute interférence, notamment les interférences

qui peuvent affecter son fonctionnement.

Important

Usage/Installation in the USA and Canada requires an

EMI suppressor. Please refer to chapter 7.1.1, page 38.

Designated use

The T10F torque flange is used exclusively for torque

and rotation speed measurement tasks, and directly

associated control and regulatory tasks. Use for any

additional purpose shall be deemed to be not as

intended.

In the interests of safety, the transducer should only be

operated as described in the Operating Manual. It is also

essential to comply with the legal and safety

requirements for the application concerned during use.

The same applies to the use of accessories.

The transducer is not a safety element within the

meaning of its designated use. Proper and safe operation

of this transducer requires proper transportation, correct

storage, assembly and mounting, and careful operation.

General dangers of failing to follow the safety

instructions

The transducer corresponds to the state of the art and is

failsafe. The transducer can give rise to remaining

dangers if it is inappropriately installed and operated by

untrained personnel.

Safety instructions

T10F A0608-14.0 HBM: public 9

Everyone involved with mounting, starting up,

maintaining, or repairing the transducer must have read

and understood the Operating Manual and in particular

the technical safety instructions.

Residual dangers

The scope of supply and performance of the transducer

covers only a small area of torque measurement

technology. In addition, equipment planners, installers

and operators should plan, implement and respond to the

safety engineering considerations of torque

measurement technology in such a way as to minimize

remaining dangers. On‐site regulations must be complied

with at all times. Reference must be made to remaining

dangers connected with torque measurement

technology.

Conversions and modifications

The transducer must not be modified from the design or

safety engineering point of view except with our express

agreement. Any modification shall exclude all liability on

our part for any damage resulting therefrom.

Qualified personnel

The transducer must only be installed and used by

qualified personnel, strictly in accordance with the

specifications and with safety requirements and

regulations. It is also essential to comply with the legal

and safety requirements for the application concerned

during use. The same applies to the use of accessories.

Qualified personnel means persons entrusted with siting,

mounting, starting up and operating the product who

possess the appropriate qualifications for their function.

Safety instructions

10 A0608-14.0 HBM: public T10F

Accident prevention

According to the prevailing accident prevention

regulations, once the torque flange has been mounted, a

covering agent or cladding has to be fitted as follows:

SThe cover or cladding must not be free to rotate.

SThe cover or cladding should avoid squeezing or

shearing and provide protection against parts that

might come loose.

SCovers and cladding must be positioned at a suitable

distance or be arranged so that there is no access to

any moving parts within.

SCovers and cladding must also be attached if the

moving parts of the torque flange are installed outside

peoples' movement and operating range.

The only permitted exceptions to the above requirements

are if the various parts and assemblies of the machine

are already fully protected by the design of the machine

or by existing safety precautions.

Warranty

In the case of complaints, a warranty can only be given if

the torque flange is returned in the original packaging.

Inhaltsverzeichnis

Andere HBM Messgerät Handbücher

Beliebte Messgerät Handbücher anderer Marken

Suaoki

Suaoki D40 Bedienungsanleitung

Elster

Elster BK-G1.6 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Deltabar FMD71 Handbuch

Duratool

Duratool D03128 Bedienungsanleitung

Vega

Vega VEGAPULS 65 Bedienungsanleitung

Tonghui

Tonghui TH2618B Bedienungsanleitung

Tenmars

Tenmars TM-801 Bedienungsanleitung

MSR

MSR 145 Bedienungsanleitung

TPS

TPS WP-82 Bedienungsanleitung

ELMETRON

ELMETRON CP-511 Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 003C30 Bedienungsanleitung

Tenma

Tenma 72-10465 Bedienungsanleitung

Endress+Hauser

Endress+Hauser Proline Promag 50 Technische Daten

Siemens

Siemens SITRANS F Coriolis FCT030 Stücklistenhandbuch

KLINGER

KLINGER CMF V Series Bedienungsanleitung

EXFO

EXFO FTB-2 Bedienungs- und Wartungshandbuch

Keysight

Keysight M8290A Bedienungsanleitung

ADTEK

ADTEK MW-5 Bedienungsanleitung